2005 JAGUAR S TYPE ad blue

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.4
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationADAPTIVE DAMPING CONTROL MODULE CA11 16-WAY / BLUE LUGGAGE COMPARTMENT, REAR
CA12 16-WAY / GREY
DAMPER SOLENOID – LH FRONT FH117 2-WAY BLACK TOP OF LH FRONT DAMPER
DAMPER SOLENOID – LH REAR CA140 2-WAY BLACK TOP OF LH REAR DAMPER
DAMPER SOLENOID – RH FRONT FH118 2-WAY BLACK TOP OF RH FRONT DAMPER
DAMPER SOLENOID – RH REAR CA111 2-WAY BLACK TOP OF RH REAR DAMPER
DYNAMIC STABILITY CONTROL MODULE FH103 47-WAY / BLACK ENGINE COMPARTMENT, RH FRONT
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
LATERAL ACCELEROMETER FH70 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
VERTICAL ACCELEROMETER – FRONT FH63 3-WAY / BLACK REARWARD OF FRONT BUMPER, LH SIDE
VERTICAL ACCELEROMETER – REAR CA17 3-WAY / BLACK LUGGAGE COMPARTMENT, RH REARHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH2 16-WAY / GREY / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH6 16-WAY GREEN / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST, ADJACENT TO FEMGROUNDS
Ground LocationCA158 LUGGAGE COMPARTMENT, LH SIDE REAR CORNER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Adaptive Damping Control Module Pin Description and CharacteristicO CA11–1 RH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–2 RH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–3 LH REAR DAMPER SOLENOID DRIVE: PWM +
O CA11–4 LH REAR DAMPER SOLENOID DRIVE: PWM –
O CA11–5 LH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–6 LH FRONT DAMPER SOLENOID DRIVE: PWM +
O CA11–7 RH FRONT DAMPER SOLENOID DRIVE: PWM –
O CA11–8 RH FRONT DAMPER SOLENOID DRIVE: PWM +
SG CA11–9 SIGNAL GROUND (INTERNALLY CONNECTED TO PIN 10): GROUND
PG CA11–10 POWER GROUND: GROUND
B+ CA11–12 IGNITION SWITCHED POWER SUPPLY (II): B+
S CA11–13 SCP –
S CA11–14 SCP +
B+ CA11–16 BATTERY POWER SUPPLY: B+
SS CA12–9 SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I CA12–10 REAR VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–11 LATERAL ACCELEROMETER SIGNAL: SENSOR SIGNAL
I CA12–12 FRONT VERTICAL ACCELEROMETER SIGNAL: SENSOR SIGNALDynamic Stability Control ModulePin Description and CharacteristicC FH103–11 CAN +
C FH103–12 CAN +
C FH103–14 CAN –
C FH103–15 CAN –Instrument ClusterPin Description and CharacteristicC FC9–12 CAN +
C FC9–13 CAN –
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicS CA102–1 SCP +
S CA102–2 SCP –

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 05.5
NOTE: FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationFRONT LH TIRE PRESSURE SENSOR FRONT LH WHEEL
FRONT LH TPMS INITIATOR FH5 2-WAY / GREY FRONT LH WHEEL ARCH
FRONT RH TIRE PRESSURE SENSOR FRONT RH WHEEL
FRONT RH TPMS INITIATOR FH26 2-WAY / GREY FRONT RH WHEEL ARCH
REAR LH TIRE PRESSURE SENSOR REAR LH WHEEL
REAR LH TPMS INITIATOR RL4 2-WAY / GREY REAR LH WHEEL ARCH
REAR RH TIRE PRESSURE SENSOR REAR RH WHEEL
REAR RH TPMS INITIATOR RR4 2-WAY / GREY REAR RH WHEEL ARCH
SPARE TIRE PRESSURE SENSOR SPARE WHEEL
TIRE PRESSURE MONITORING SYSTEM MODULE CA146 16-WAY / BLUE LUGGAGE COMPARTMENT, RH REAR CA147 16-WAY / GREY
TIRE PRESSURE RECEIVER MODULE RF15 3-WAY / BLACK BELOW CENTER CONSOLEHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFH1 22-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS ADJACENT TO FRONT RH WHEEL ARCH
FH3 2-WAY GREY / LINK HARNESS ADJACENT TO FRONT LH WHEEL ARCH
RF34 16-WAY GREEN / ROOF HARNESS HEADLINER, CLOSE TO ROOF CONSOLE
RL2 8-WAY BLACK / LINK HARNESS ADJACENT TO REAR LH WHEEL ARCH
RR2 6-WAY GREY / LINK HARNESS ADJACENT TO REAR RH WHEEL ARCHGROUNDS
Ground LocationCA116 BEHIND REAR SEAT BACK, RH SIDE
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Tire Pressure Monitoring System Module
Pin Description and CharacteristicO CA146–5 REAR LH TPMS INITIATOR: RF 125kHz +
O CA146–6 REAR LH TPMS INITIATOR: RF 125kHz –
O CA146–7 REAR RH TPMS INITIATOR: RF 125kHz +
O CA146–8 REAR RH TPMS INITIATOR: RF 125kHz –
O CA146–13 FRONT LH TPMS INITIATOR: RF 125kHz +
O CA146–14 FRONT LH TPMS INITIATOR: RF 125kHz –
O CA146–15 FRONT RH TPMS INITIATOR: RF 125kHz +
O CA146–16 FRONT RH TPMS INITIATOR: RF 125kHz –
I CA147–4 TIRE PR ESSURE DATA:
B+ CA147–8 IGNITION SWITCHED POWER SUPPLY (II): B+
C CA147–10 CAN –
C CA147–11 CAN +
PG CA147–12 POWER GROUND: GROUND
B+ CA147–16 BATTERY POWER SUPPLY: B+Tire Pressure Receiver Module
Pin Description and CharacteristicO RF15–1 OUTPUT SIGNAL TO TPMS MODULE
PG RF15–2 POWER GROUND: GROUND
B+ RF15–3 BATTERY POWER SUPPLY: B+

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 07.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
ENGINE COOLANT LEVEL SENSOR CP3 2-WAY / BLACK ENGINE COMPARTMENT, COOLANT EXPANSION TANK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL LEVEL SENSOR – LH SIDE (DIESEL) FP14 2-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – LH SIDE (GASOLINE) FP3 4-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – RH SIDE (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (GASOLINE) FP4 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS N/A ONLY) FP8 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS SC ONLY) FP9 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LOW LEVEL SWITCH (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
OIL PRESSURE SWITCH (DIESEL) C29 1-WAY / BLACK ADJACENT TO OIL FILTER
OIL PRESSURE SWITCH (GASOLINE) PI46 1-WAY / BLACK ADJACENT TO OIL FILTER
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
WASHER FLUID LEVEL SWITCH FH37 2-WAY / BLACK WASHER FLUID CONTAINERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationCP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
CP7 4-WAY / BLACK / FRONT END HARNESS ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
FP6 2-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicI FH9–15 WASHER FLUID LEVEL SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
I FH59–9 ENGINE OIL PRESSURE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
PG FH59–12 POWER GROUND: GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
I FC8–3 SEAT BELT AUDIBLE WARNING REQUEST: AUDIBLE WARNING REQUEST ACTIVE = GROUND
B+ FC8–4 IGNITION SWITCHED POWER SUPPLY (I): B+
I FC8–5 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
I FC8–6 KEY-IN AUDIBLE WARNING (J-GATE): GROUND WHEN NOT-IN-PARK
B+ FC8–14 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
I FC8–19 LOW ENGINE COOLANT LEVEL WARNING: GROUND WHEN COOLANT LEVEL LOW
I FC8–23 AIR BAG WARNING: HARD-WIRED TO AIR BAG INDICATOR
B+ FC8–24 IGNITION SWITCHED POWER SUPPLY (II) (AIRBAG WARNING): B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–1 TRIP COMPUTER – MESSAGE CENTER SIGNALS: VARIABLE RESISTANCE
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
C FC9–12 CAN +
C FC9–13 CAN –
I FC9–17 TRIP CYCLE SWITCH – MESSAGE CENTER SIGNAL: VARIABLE RESISTANCE
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicB+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–15 GASOLINE, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA101–16 GASOLINE, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–17 LOW LEVEL SWITCH
I CA102–20 LOW LEVEL SWITCH
PG CA103–11 POWER GROUND: GROUND
PG CA103–12 POWER GROUND: GROUND
I CA103–17 DIESEL, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA103–18 DIESEL, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
SG CA103–23 FUEL LEVEL SENSORS SIGNAL GROUND: GROUND
PG CA103–25 POWER GROUND: GROUND
PG CA103–26 POWER GROUND: GROUND

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 09.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCOURTESY LAMP – DRIVER DOOR DD6 2-WAY BLACK DRIVER DOOR CASING
COURTESY LAMP – PASSENGER DOOR PD3 2-WAY BLACK PASSENGER DOOR CASING
DOOR LATCH ASSEMBLY – DRIVER DT5 10-WAY / BLACK DRIVER DOOR
DOOR LATCH ASSEMBLY – LH REAR CA81 10-WAY / BLACK LH REAR DOOR
DOOR LATCH ASSEMBLY – PASSENGER PT3 10-WAY / BLACK PASSENGER DOOR
DOOR LATCH ASSEMBLY – RH REAR CA90 10-WAY / BLACK RH REAR DOOR
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
FASCIA LAMP – LH FC44 2-WAY / WHITE INSTRUMENT PANEL, LH SIDE
FASCIA LAMP – RH FC51 2-WAY / WHITE INSTRUMENT PANEL, RH SIDE
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
GLOVE BOX LAMP GL1 2-WAY / BLACK GLOVE BOX
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL
FC9 32-WAY / BLACK
MAP LAMP – LH REAR RF20 3-WAY / BLACK LH REAR ASSIST HANDLE
MAP LAMP – RH REAR RF23 3-WAY / BLACK RH REAR ASSIST HANDLE
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
ROOF CONSOLE CA250 22-WAY / BLACK ROOF HEADLINER
SUN VISOR LAMP – LH RF12 2-WAY / BLACK LH SUN VISOR
SUN VISOR LAMP – RH RF24 2-WAY / BLACK RH SUN VISOR
TRUNK AJAR SWITCH CA26 2-WAY / BLACK LUGGAGE COMPARTMENT LID
TRUNK LAMP – LH CA96 2-WAY / BLACK LUGGAGE COMPARTMENT, LH SIDE
TRUNK LID LAMP CA167 2-WAY / BLACK LUGGAGE COMPARTMENT LIDHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
DT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC33 16-WAY / GREEN / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, RH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
PD4 10-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR HARNESS PASSENGER DOOR
PT1 14-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR TRIM HARNESS PASSENGER DOOR
RF34 16-WAY / GREEN / CABIN HARNESS TO DOOR HARNESS ‘D’ POST, UNDER PARCEL SHELFGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA116 BEHIND REAR SEAT BACK, RH SIDE
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
CA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Driver Door Module Pin Description and CharacteristicS CA85–3 SCP +
S CA85–4 SCP –
PG CA85–8 POWER GROUND: GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
I DT2–16 DRIVER DOOR ALARM SET / LOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I DT2–17 DRIVER DOOR ALARM RESET / UNLOCK SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUNDFront Electronic ModulePin Description and CharacteristicI CA24–15 PASSENGER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA31–8 DRIVER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
— CA31–12 INTERIOR LIGHTING ACTIVATE: TO ACTIVATE, FEM SWITCHES CIRCUIT TO GROUND (PWM)
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
PG FH60–11 POWER GROUND: GROUNDInstrument Cluster Pin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
SG FC8–8 ROOF CONSOLE COURTESY LAMP SWITCH GROUND: SWITCH OPEN = GROUND
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–32 SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –Rear Electronic ModulePin Description and CharacteristicO CA100–11 TRUNK LAMPS ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
B+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–17 LHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–14 TRUNK AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I CA103–16 LHD – LH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND RHD – RH REAR DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 09.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING CONTROL MODULE – PANEL FC27 26-WAY / GREY CENTER CONSOLE
FC28 22-WAY / GREY
AUDIO UNIT FC94 20-WAY / BLACK CENTER CONSOLE
FC96 ANTENNA CONNECTOR
FC108 FIBER OPTIC CONNECTOR
AUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
CENTER CONSOLE SWITCH PACK FC113 8-WAY / BLACK CENTER CONSOLE FC119 8-WAY / BLACK
CIGAR LIGHTER CA109 3-WAY / BLACK CENTER CONSOLE
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL FLAP / TRUNK RELEASE SWITCH PACK FC43 10-WAY / GREY INSTRUMENT PANEL
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL
FC9 32-WAY / BLACK
J-GATE MODULE CA245 16-WAY / BLACK J-GATE ASSEMBLY
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
POWER POINT CA237 3-WAY / BROWN ADJACENT TO CIGAR LIGHTER
PRIMARY JUNCTION FUSE BOX CA2 26-WAY / BLACK RH ‘A’ POST CA56 8-WAY / BLACK
FC37 26-WAY / BLACK
FH7 6-WAY / BLACK
FH53 10-WAY / BLACK
ROOF CONSOLE CA250 22-WAY / BLACK ROOF HEADLINER
STEERING WHEEL LIGHTING SQ1 4-WAY / BLACK STEERING WHEEL SQ3 4-WAY / BLACK
TELEMATICS DISPLAY FC92 22-WAY / BLACK CENTER CONSOLE
WINDOW SWITCH – LH REAR CA78 5-WAY / GREEN LH REAR DOOR ARM REST
WINDOW SWITCH – PASSENGER PD1 5-WAY / GREEN PASSENGER DOOR ARM REST
WINDOW SWITCH – RH REAR CA95 5-WAY / GREEN RH REAR DOOR ARM RESTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
FC23 10-WAY / GREY / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, LH SIDE
FC117 10-WAY / BLACK / STEERING WHEEL CASSETTE STEERING COLUMN
PD4 10-WAY / GREY / CABIN HARNESS TO PASSENGER DOOR HARNESS PASSENGER DOORGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA141 UNDER LH FRONT SEAT
CA154 UNDER RH FRONT SEAT
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Air Conditioning Control Module – Panel Pin Description and CharacteristicI FC28–15 PANEL ILLUMINATION (DIMMER-CONTROLLED): B+ (PWM)Audio UnitPin Description and CharacteristicI FC94–17 DIMMER-CONTROLLED ILLUMINATION: PWM, 80 Hz, GROUND = 0% DUTY CYCLE, B+ = 100% DUTY CYCLEFront Electronic ModulePin Description and CharacteristicB+ CA31–1 SWITCHED SYSTEM POWER SUPPLY: B+
O CA31–11 BACKLIGHTING ACTIVATE: B+ (PWM)
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
PG FH59–12 POWER GROUND: GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
SS FC8–11 DIMMER SUPPLY VOLTAGE: B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–2 MAIN LIGHTING SWITCH SIGNALS – OFF, SIDE, DIP, AUTOLAMP: VARIABLE RESISTANCE
I FC9–4 DIMMER SIGNAL: VARIABLE VOLTAGE
I FC9–5 MAIN LIGHTING SWITCH SIGNALS – EXIT DELAY: VARIABLE RESISTANCE
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 10.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationCOLUMN AND PEDAL ADJUST SWITCH FC45 8-WAY / BLACK STEERING COLUMN COWLING
DOOR LATCH ASSEMBLY – DRIVER DT5 10-WAY / BLACK DRIVER DOOR
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL
FC9 32-WAY / BLACK
PEDAL ADJUST MOTOR CA234 2-WAY / BLACK PEDAL MOUNTING BRACKET ASSEMBLY
CA235 3-WAY / BLACK
STEERING COLUMN MOTOR, SOLENOIDS AND POSITION SENSORS FC115 10-WAY / BLACK UPPER STEERING COLUMNHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
DT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDEGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Driver Door Module Pin Description and CharacteristicS CA85–3 SCP +
S CA85–4 SCP –
PG CA85–8 POWER GROUND: GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
O DD4–7 MEMORY SET INDICATOR: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
I DD4–10 MEMORY 1: GROUND WHEN SELECTED
I DD4–11 MEMORY 2: GROUND WHEN SELECTED
I DD4–25 MEMORY SET: GROUND WHEN SELECTEDFront Electronic ModulePin Description and CharacteristicI CA24–5 PEDAL ADJUST MOTOR POSITION SENSOR SIGNAL: VARIABLE VOLTAGE
O CA24–12 PEDAL ADJUST MOTOR DRIVE – IN: TO ACTIVATE, FEM SWITCHES CIRCUIT TO B+
SG CA24–18 PEDAL ADJUST MOTOR POSITION SENSOR SIGNAL GROUND: GROUND
O CA24–26 PEDAL ADJUST MOTOR DRIVE – OUT: TO ACTIVATE, FEM SWITCHES CIRCUIT TO B+
I CA31–8 DRIVER DOOR AJAR SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
SS CA31–16 PEDAL ADJUST MOTOR POSITION SENSOR SIGNAL SUPPLY VOLTAGE: NOMINAL 5 V
I FH9–8 PEDALS OUT REQUEST (NORMALLY OPEN): OPEN CIRCUIT / GROUND
I FH9–17 PEDALS IN REQUEST (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
S FH59–7 SCP +
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
PG FH60–11 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
O FC8–10 STEERING COLUMN POSITION FEEDBACK POTENTIOMETERS SUPPLY VOLTAGE: B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
O FC8–25 STEERING COLUMN IN / OUT FUNCTION SOLENOID DRIVE: B+ WHEN ACTIVATED
O FC8–26 STEERING COLUMN UP / DOWN FUNCTION SOLENOID DRIVE: B+ WHEN ACTIVATED
O FC8–27 STEERING COLUMN MOTOR DOWN / IN DRIVE: B+ WHEN ACTIVATED
B+ FC8–29 BATTERY POWER SUPPLY (COLUMN MOTOR)
O FC8–30 STEERING COLUMN MOTOR UP / OUT DRIVE: B+ WHEN ACTIVATED
SG FC8–32 SIGNAL GROUND: GROUND
SG FC9–11 STEERING COLUMN POSITION FEEDBACK POTENTIOMETERS SIGNAL GROUND: GROUND
I FC9–18 STEERING COLUMN MOVEMENT SWITCH SIGNAL: VARIABLE VOLTAGE
I FC9–20 STEERING COLUMN UP / DOWN POSITION FEEDBACK POTENTIOMETER SIGNAL: VARIABLE VOLTAGE
I FC9–21 STEERING COLUMN IN / OUT POSITION FEEDBACK POTENTIOMETER SIGNAL: VARIABLE VOLTAGE
I FC9–22 FUNCTION SELECT SIGNAL: VARIABLE RESISTANCE
SG FC9–23 STEERING COLUMN MOVEMENT / SELECT SIGNAL GROUND: GROUND
S FC9–25 SCP +
S FC9–26 SCP –

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 10.2
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAIR CONDITIONING CONTROL MODULE – PANEL FC27 26-WAY / GREY CENTER CONSOLE
FC28 22-WAY / GREY
AIR CONDITIONING CONTROL MODULE – REMOTE FC40 26-WAY / GREY BEHIND INSTRUMENT PANEL, RH SIDE (LHD), LH SIDE (RHD) FC41 22-WAY / GREY
DOOR MIRROR – DRIVER DT6 22-WAY / BLACK DRIVER DOOR
DOOR MIRROR – PASSENGER CA19 22-WAY / BLACK PASSENGER DOOR
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
HEATED REAR WINDOW CA20 2-WAY / GREY CONNECTOR LOCATED BELOW PARCEL SHELF, LH SIDE
HEATED REAR WINDOW RELAY — — REAR POWER DISTRIBUTION FUSE BOX – R1
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR
CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
REAR POWER DISTRIBUTION FUSE BOX — — LUGGAGE COMPARTMENTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
DT8 14-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOORGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA156 LUGGAGE COMPARTMENT, RH SIDE
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Air Conditioning Control Module – Panel Pin Description and CharacteristicC FC28–1 CAN –
C FC28–12 CANAir Conditioning Control Module – RemotePin Description and CharacteristicC FC41–1 CAN –
C FC41–12 CAN +Driver Door ModulePin Description and CharacteristicS CA85–3 SCP +
S CA85–4 SCP –
PG CA85–7 POWER GROUND: GROUND
PG CA85–8 POWER GROUND: GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
B+ CA85–12 SWITCHED SYSTEM POWER SUPPLY: B+
I DD4–3 MIRROR MOVEMENT UP: GROUND WHEN ACTIVATED
O DD4–7 MEMORY SET INDICATOR: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
I DD4–10 MEMORY 1: GROUND WHEN SELECTED
I DD4–11 MEMORY 2: GROUND WHEN SELECTED
I DD4–19 MIRROR MOVEMENT RIGHT: GROUND WHEN ACTIVATED
I DD4–20 MIRROR MOVEMENT DOWN: GROUND WHEN ACTIVATED
I DD4–21 MIRROR MOVEMENT LEFT: GROUND WHEN ACTIVATED
I DD4–23 LH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTED
I DD4–24 RH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTED
I DD4–25 MEMORY SET: GROUND WHEN SELECTED
O DT2–1 DRIVER DOOR MIRROR LEFT: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–2 DRIVER DOOR MIRROR RIGHT: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–3 DRIVER DOOR MIRROR UP: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O DT2–4 DRIVER DOOR MIRROR DOWN: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
SS DT2–5 DRIVER DOOR MIRROR POSITION SENSORS SIGNAL SUPPLY VOLTAGE: B+
I DT2–14 DRIVER DOOR MIRROR LEFT / RIGHT POSITION FEEDBACK SIGNAL: VARIABLE VOLTAGE
I DT2–15 DRIVER DOOR MIRROR UP / DOWN POSITION FEEDBACK SIGNAL: VARIABLE VOLTAGE
SG DT2–19 DRIVER DOOR MIRROR POSITION SENSORS SIGNAL GROUND: GROUNDFront Electronic ModulePin Description and CharacteristicI CA24–7 PASSENGER DOOR MIRROR LEFT / RIGHT POSITION FEEDBACK SIGNAL: VARIABLE VOLTAGE
SS CA24–8 PASSENGER DOOR MIRROR POSITION SENSORS SIGNAL SUPPLY VOLTAGE: B+
I CA24–11 PASSENGER DOOR MIRROR UP / DOWN POSITION FEEDBACK: VARIABLE VOLTAGE
O CA24–20 PASSENGER DOOR MIRROR UP: TO ACTIVATE, FEM SWITCHES CIRCUIT TO B+
O CA24–21 PASSENGER DOOR MIRROR DOWN: TO ACTIVATE, FEM SWITCHES CIRCUIT TO B+
SG CA24–22 PASSENGER DOOR MIRROR POSITION SENSORS SIGNAL GROUND: GROUND
O CA24–23 PASSENGER DOOR MIRROR LEFT: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA24–24 PASSENGER DOOR MIRROR RIGHT: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
S FH59–1 SCP –
S FH59–7 SCP +
B+ FH60–1 SWITCHED SYSTEM POWER SUPPLY: B+
PG FH60–11 POWER GROUND: GROUNDInstrument Cluster Pin Description and CharacteristicS FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicB+ CA101–3 BATTERY POWER SUPPLY: B+
S CA102–1 SCP +
S CA102–2 SCP –
O CA102–7 HEATED REAR WINDOW ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
PG CA102–12 POWER GROUND: GROUND
B+ CA103–13 SWITCHED SYSTEM POWER SUPPLY: B+

Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 10.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationDOOR MIRROR – DRIVER DT6 22-WAY / BLACK DRIVER DOOR
DOOR MIRROR – PASSENGER CA19 22-WAY / BLACK PASSENGER DOOR
DOOR SWITCH PACK – DRIVER DD2 26-WAY / YELLOW DRIVER DOOR ARM REST
DRIVER DOOR MODULE CA85 12-WAY / BLACK DRIVER DOOR
DD4 26-WAY / NATURAL
DT2 20-WAY / BLACK
ELECTROCHROMIC REAR VIEW MIRROR AND COMPASS RF5 6-WAY / BLACK WINDSHIELD, CENTER
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURALHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationDD8 16-WAY / BLUE / CABIN HARNESS TO DRIVER DOOR HARNESS DRIVER DOOR
DT10 10-WAY / GREY / CABIN HARNESS TO DRIVER DOOR TRIM HARNESS DRIVER DOOR
RF34 16-WAY / GREEN / CABIN HARNESS TO DOOR HARNESS ‘D’ POST, UNDER PARCEL SHELFGROUNDS
Ground LocationCA30 LH LOWER ‘A’ POST, ADJACENT TO THE GENERAL ELECTRONIC CONTROL MODULE (REARWARD OF FH77)
CA50 RH LOWER ‘A’ POST, BELOW PRIMARY JUNCTION FUSE BOX
CA116 BEHIND REAR SEAT BACK, RH SIDE
CA156 LUGGAGE COMPARTMENT, RH SIDE
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Driver Door ModulePin Description and CharacteristicO CA85–5 MIRROR FOLD FLAT DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
O CA85–6 MIRROR FOLD FLAT DRIVE: TO ACTIVATE, DDM SWITCHES CIRCUIT TO B+
PG CA85–7 POWER GROUND: GROUND
PG CA85–8 POWER GROUND: GROUND
B+ CA85–11 BATTERY POWER SUPPLY: B+
B+ CA85–12 SWITCHED SYSTEM POWER SUPPLY: B+
I DD4–20 MIRROR FOLD FLAT (MIRROR SELECT IN NEUTRAL POSITION): GROUND WHEN ACTIVATED
I DD4–23 LH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTED
I DD4–24 RH DOOR MIRROR MOVEMENT SELECT: GROUND WHEN SELECTEDRear Electronic ModulePin Description and CharacteristicB+ CA101–3 BATTERY POWER SUPPLY: B+
S CA102–1 SCP +
S CA102–2 SCP –
O CA102–7 HEATED REAR WINDOW ACTIVATE: TO ACTIVATE, REM SWITCHES CIRCUIT TO GROUND
PG CA102–12 POWER GROUND: GROUND
B+ CA103–13 SWITCHED SYSTEM POWER SUPPLY: B+