2005 INFINITI FX35 Key switch

SRS-24
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
7. If no malfunction is detected on “SELF-DIAG [CURRENT]”,
repair of SRS is completed. Go to step 8.
If any malfunction is detected on “SELF-DIAG [CURRENT]”, the
malfunctioning part is not repaired completely or another mal-
functioning part is detected. Go to SRS-19, "
DIAGNOSTIC
PROCEDURE 2" , and repair malfunctioning part completely.
8. Touch “ERASE”. NOTE:
Touch “ERASE” to clear the memory of the malfunction (“SELF-
DIAG [PAST]”).
If the memory of the malfunction in “SELF-DIAG [PAST]” is not
erased, the User mode shows the system malfunction by the
operation of the warning lamp even if the malfunction is repaired
completely.
9. Touch “BACK” key of CONSULT-II to “SELECT DIAG MODE” screen. Touch “SELF-DIAG [PAST]”.
10. Make sure no malfunction is detected on “SELF-DIAG [PAST]”.
11. Touch “BACK” key of CONSULT-II until “SELECT SYSTEM” appears in order to return to User mode from Diagnosis mode.
12. Turn ignition switch OFF then turn off and disconnect CON- SULT-II. Go to SRS-17, "
DIAGNOSTIC PROCEDURE 1" .
SRS701
SRS773
SRS697
SRS702

SRS-26
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
6. Touch “SELF-DIAG [PAST]”.
7. If diagnostic codes are displayed on “SELF-DIAG [PAST]”, go to
step 10.
If no malfunction is detected on “SELF-DIAG [PAST]”, touch
“BACK” and go back to “SELECT DIAG MODE”.
8. Touch “TROUBLE DIAG RECORD”. NOTE:
With “TROUBLE DIAG RECORD”, diagnosis results previously
erased by a reset operation can be displayed.
9. Diagnostic code is displayed on “TROUBLE DIAG RECORD”.
10. Touch “PRINT”.
11. Compare diagnostic codes to SRS-25, "
DIAGNOSTIC PROCE-
DURE 5" .
12. Touch “BACK” key of CONSULT-II until “SELECT SYSTEM” appears.
13. Turn ignition switch OFF, then turn off and disconnect CON- SULT-II, and both battery cables.
14. Repair the system as outlined by the “Repair order” in “Intermit- tent Malfunction Diagnostic Code Chart”, that corresponds to the
SRS697
SRS700
SRS702
SRS697
SHIA0182E

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G H
I
J
K L
M
SECTION WT
A
B
WT
Revision: 2005 July 2005 FX
ROAD WHEELS & TIRES
PREPARATION ........................................................... 2
Special Service Tools .......................................... ..... 2
Commercial Service Tools ................................... ..... 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ........................................... ..... 3
NVH Troubleshooting Chart ................................ ..... 3
ROAD WHEEL ....................................................... ..... 4
Inspection ............................................................ ..... 4
ALUMINUM WHEEL ........................................ ..... 4
STEEL WHEEL ................................................ ..... 4
ROAD WHEEL TIRE ASSEMBLY ......................... ..... 5
Balancing Wheels (Bonding Weight Type) .......... ..... 5
REMOVAL ........................................................ ..... 5
WHEEL BALANCE ADJUSTMENT ................. ..... 5
Tire Rotation ........................................................ ..... 6
LOW TIRE PRESSURE WARNING SYSTEM ....... ..... 7
System Components ........................................... ..... 7
System Description ............................................. ..... 7
TRANSMITTER ................................................ ..... 7
REMOTE KEYLESS ENTRY RECEIVER ........ ..... 7
BCM (BODY CONTROL MODULE) ................. ..... 8
LOW TIRE PRESSURE WARNING LAMP ...... ..... 8
DISPLAY UNIT ................................................. ..... 8
CAN COMMUNICATION ....................................... ..... 9
System Description ............................................. ..... 9
TROUBLE DIAGNOSES ....................................... ... 10
Schematic ........................................................... ... 10
Wiring Diagram ................................................... .... 11
Control Unit Input/Output Signal Standard .......... ... 14
ID Registration Procedure ................................... ... 16
ID REGISTRATION WITH ACTIVATION TOOL ... 16
ID REGISTRATION WITHOUT ACTIVATION
TOOL ............................................................... ... 17
Transmitter Wake Up Operation .......................... ... 18
WITH ACTIVATION TOOL ............................... ... 18
Self-Diagnosis ..................................................... ... 19
DESCRIPTION ................................................. ... 19
FUNCTION ....................................................... ... 19
LOW TIRE PRESSURE WARNING LAMP DIAG-
NOSTIC CHART .............................................. ... 19 CONSULT-II ......................................................
... 20
WORK SUPPORT MODE ................................ ... 21
SELF-DIAGNOSTIC RESULTS MODE ............ ... 21
DATA MONITOR MODE ................................... ... 22
ACTIVE TEST MODE ...................................... ... 22
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ................................................... ... 25
INTRODUCTION .............................................. ... 25
WORK FLOW ................................................... ... 25
Preliminary Check ............................................... ... 26
Malfunction Code/Symptom Chart ....................... ... 27
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ..................................................................... ... 28
Inspection 1: Transmitter or Control Unit (BCM) .. ... 28
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 28
Inspection 2: Transmitter - 1 ................................ ... 28
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................ ... 28
Inspection 3: Transmitter - 2 ................................ ... 29
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 29
Inspection 4: Vehicle Speed Signal ..................... ... 30
MALFUNCTION CODE NO. 52 ........................ ... 30
TROUBLE DIAGNOSIS FOR SYMPTOMS ........... ... 31
Inspection 1: Warning Lamp Does Not Come On
When Ignition Switch Is Turned On ..................... ... 31
Inspection 2: Warning Lamp Stays On When Ignition
Switch Is Turned On ............................................ ... 31
Inspection 3: Warning Lamp Blinks When Ignition
Switch Is Turned On ............................................ ... 33
Inspection 4: Turn Signal Lamp Blinks When Ignition
Switch Is Turned On ............................................ ... 34
Inspection 5: ID Registration Can Not Be Completed ... 34
REMOVAL AND INSTALLATION .......................... ... 35
Transmitter .......................................................... ... 35
REMOVAL ........................................................ ... 35
INSTALLATION ................................................ ... 35
SERVICE DATA ..................................................... ... 37
Road Wheel ......................................................... ... 37
Tire ...................................................................... ... 37
Tightening Torque ................................................ ... 37

WT-8
LOW TIRE PRESSURE WARNING SYSTEM
Revision: 2005 July 2005 FX
BCM (BODY CONTROL MODULE)
The BCM reads the air pressure signal received by the remote key-
less entry receiver, and controls the low tire pressure warning lamp
and the buzzer operations as shown below. It also has a judgement
function to detect a system malfunction.
LOW TIRE PRESSURE WARNING LAMP
The combination meter receives tire pressure status from the BCM
using CAN communication. When a low tire pressure condition is
sensed by the BCM, the combination meter low tire pressure warn-
ing lamp and buzzer are activated.
DISPLAY UNIT
Displays the air pressure of each tire.

After the ignition switch is turned ON, the pressure values are
not displayed until the data of each wheel stabilizes.
Condition Warning lamp Buzzer
Less than 178 kPa (1.78 kg/cm
2 , 26 psi)
[Flat tire] ON Sounds for 10 sec.
System malfunction ON OFF
SEIA0591E
SEIA0434E
SKIA5994E

WT-14
TROUBLE DIAGNOSES
Revision: 2005 July 2005 FX
Control Unit Input/Output Signal StandardAES000Z4
Standards using a circuit tester and oscilloscope
Terminal
Item Condition Voltage (V)
Approx. value
+–
15 (G)
Ground Tire pressure warning check
connector Always 5V
18 (B) Remote keyless entry receiver
(Ground) —0V
19 (R) Remote keyless entry receiver
(Power supply) Stand-by
Press any of the keyfob
switches
20 (Y) Remote keyless entry receiver
(Signal) Stand-by
Press any of the keyfob
switches
38 (W/L) Ignition switch Ignition switch ON or START Battery voltage (12V)
39 (L) Data line (CAN H) — —
40 (R) Data line (CAN L) — —
42 (L/R) Battery power supply (Fuse) Always Battery voltage (12V)
45 (G/W) Turn signal (left)

Ignition switch ON

Combination switch is turn
signal (left)
OCC3879D
OCC3882D
OCC3881D
OCC3880D
SKIA3009J

TROUBLE DIAGNOSES WT-27
C
D
F
G H
I
J
K L
M A
B
WT
Revision: 2005 July 2005 FX
Malfunction Code/Symptom ChartAES000ZA
Code/Symptom Malfunction part Reference
page
15
16
17
18 Front-left tire pressure drops to 178 kPa (1.78 kg/cm
2 , 26 psi) or
less.
Front-right tire pressure drops to 178 kPa (1.78 kg/cm
2 , 26 psi) or
less.
Rear-right tire pressure drops to 178 kPa (1.78 kg/cm
2 , 26 psi) or
less.
Rear-left tire pressure drops to 178 kPa (1.78 kg/cm
2 , 26 psi) or
less. —
21
22
23
24 Transmitter no data (front - left)
Transmitter no data (front - right)
Transmitter no data (rear - right)
Transmitter no data (rear - left) WT-28
31
32
33
34 Transmitter checksum error (front - left)
Transmitter checksum error (front - right)
Transmitter checksum error (rear - right)
Transmitter checksum error (rear - left) WT-28
35
36
37
38 Transmitter pressure data error (front - left)
Transmitter pressure data error (front - right)
Transmitter pressure data error (rear - right)
Transmitter pressure data error (rear - left) WT-29
41
42
43
44 Transmitter function code error (front - left)
Transmitter function code error (front - right)
Transmitter function code error (rear - right)
Transmitter function code error (rear - left) WT-28
45
46
47
48 Transmitter battery voltage low (front - left)
Transmitter battery voltage low (front - right)
Transmitter battery voltage low (rear - right)
Transmitter battery voltage low (rear - left) WT-28
52 Vehicle speed signal
WT-30
Warning lamp does not come on when
ignition switch is turned on. Fuse or combination meter
BCM connector or circuit
BCM WT-31
Warning lamp stays on when ignition
switch is turned on. Combination meter
BCM connector or circuit
BCM WT-31
Warning lamp blinks when ignition
switch is turned on. BCM connector or circuit
BCM
Transmitter's mode off
ID registration not yet WT-33
Turn signal lamp blinks when ignition
switch is turned on. BCM connector or circuit
BCM WT-34
ID registration can not be operated. Transmitter
Remote keyless entry receiver connector or circuit
Remote keyless entry receiver
BCM connector or circuit
BCM WT-34