2005 HYUNDAI GX350 L ECO mode

1
FEATURES OF YOUR HYUNDAI
3
KEY
BREAKING IN YOUR NEW HYUNDAI
B010E01A-AATGasolines for Cleaner AirTo help contribute to cleaner air, Hyundai rec-
ommends that you use gasolines treated with
detergent additives, which help prevent deposit
formation in the engine. These gasolines will
help the engine run cleaner and enhance per-
formance of the Emission Control System.B010F01A-AATOperation in Foreign CountriesIf you are going to drive your Hyundai in another
country, be sure to:
o Observe all regulations regarding registra-
tion and insurance.
o Determine that acceptable fuel is available.
B020A01S-AATDuring the First 1,200 Miles (2,000 Km)No formal "break-in" procedure is required with
your new Hyundai. However, you can contrib-
ute to the economical operation and durability of
your Hyundai by observing the following recom-
mendations during the first 1,200 miles (2,000
km).
o Don't drive faster than 55 MPH (88 km/h).
o While driving, keep your engine speed (rpm,
or revolutions per minute) between 2,000
rpm and 4,000 rpm.
o Use moderate acceleration. Don't start
quickly or depress the accelerator pedal
fully.
o For the first 200 miles (300 km), try to avoid
hard stops.
o Don't lug the engine (in other words, don't
drive so slowly in too high a gear that the
engine "bucks"-shift to a lower gear).
o Whether going fast or slow, vary your speed
from time to time.
o Don't let the engine idle longer than 3 minutes
at one time.
o Don't tow a trailer during the first 1,200 miles
(2,000 km) of operation.
B030A01Y-AATKEYSFor greater convenience, your Hyundai has
two master keys and a sub key. The master
keys will open all locks on your vehicle. The sub
key will only function in the ignition and the door
locks.
Leaving your sub key with a parking attendant
will ensure that your vehicle's trunk, trunk lid
release, glovebox compartment and rear trunk
access may not be unlocked in your absence.NOTE:Before leaving your sub key with a parking
attendant, make sure that the lock levers of
the rear seat back lock and the trunk lid lock
are switched to the "LOCK" position.
HXG116
Master key
Sub key
xgflhma-1.p656/16/04, 3:02 PM 3
ProCarManuals.com

1
FEATURES OF YOUR HYUNDAI
15
Reverse Parking Aid FunctionWhen the "AUTO" button is "ON" and the
vehicle is moving backward, the outside rear-
view mirror(s) will move downward to aid re-
verse parking safely. According to the position
of the outside rearview mirror switch knob, the
outside rearview mirror(s) will operate as fol-
lows.
L: When the remote control outside rearview
mirror switch knob is selected to the "L"
position, both of the outside rearview mir-
rors will move downward.
R: When the remote control outside rearview
mirror switch knob is selected to the "R"
position, only the passenger's outside rear-
view mirror will move downward.
Neutral: When the remote control outside rear-
view mirror switch knob is placed in
the middle position, the outside rear-
view mirrors will not operate while the
vehicle is moving backward.NOTE:When the ignition key is in the "LOCK"
position, the selector lever is moved to any
position except "R" position, or the remote
control outside rearview mirror switch knob
is placed in the middle position, the outside
rearview mirrors will automatically revert to
original position.
!
CAUTION:
In the following conditions, the I.M.S will
not operate.
1. When the "1" or "2" button is not pushed
within five seconds.
2. When the seat is being adjusted.
3. When the "STOP" button is pushed.
4. While the vehicle is moving.To activate the memorized positionWhen you push button "1" or "2", the driving
position will be automatically adjusted to the
position recorded for that button.To memorize driving position1. Turn the ignition key "ON".
2. Adjust the driver's seat and outside rearview
mirrors to the desired position.
3. Push the "M" button on the I.M.S until the
signal beeps.
4. Within five seconds, push button "1" or "2"
until the signal beeps twice. The beep sounds
mean that the positions are memorized in the
I.M.S.
"AUTO" button functionWhen the "AUTO" button is "ON", the system
will move the driver's seat forward or rearward
so you can comfortably enter and exit the
vehicle.
o It will move driver's seat rearward when the
ignition key is pulled out.
o It will move driver's seat forward when the
ignition key is inserted.Note:In order for the "AUTO" functions to work,
the parking brake must be applied.
CAUTION:
In the following conditions, the "AUTO"
mode will not operate.
1. When AUTO button is in "OFF".
2. When the seat is being adjusted.
3. When the shift lever is positioned in
other than "P" position.
!
xgflhma-1.p656/16/04, 3:02 PM 15
ProCarManuals.com

1
FEATURES OF YOUR HYUNDAI
21
the seat belt operates in the same way as the
driver's seat belt (Emergency Locking Retrac-
tor Type). It automatically adjusts to the proper
length only after the lap belt portion of the seat
belt is adjusted manually so that it fits snugly
around your hips. When the seat belt is fully
extended from the retractor to allow the instal-
lation of a child restraint system, the seat belt
operation changes to allow the belt to retract, but
not to extend. (Automatic Locking Retractor
Type). See page 1-27.NOTE:Although the combination retractor pro-
vides the same level of protection for seated
passengers in either emergency or auto-
matic locking modes, it is recommended
that seated passengers use the emergency
locking feature for improved convenience.
The automatic locking function is intended
to facilitate child restraint installation. To
convert from the automatic locking feature
to the emergency locking operation mode,
allow the unbuckled seat belt to fully re-
tract.
WARNING:
o For maximum restraint system protec-
tion, the seat belts must always be used
whenever the car is moving.
o Seat belts are most effective when
seatbacks are in the upright position.
o Children must always be seatbelted in
the rear seats. Never allow children to
ride in the front passenger seat.
o The shoulder belt should be positioned
midway over the shoulder nearest the
door for the most effective protection.
Never wear the seat belt under the arm
nearest the door. Wearing the belt under
the arm nearest the door could cause
serious or fatal injuries in an accident.
o Avoid wearing twisted seat belts. A
twisted belt can't do its job as well. In a
collision, it could even cut into you. Be
sure the belt webbing is straight and not
twisted.
o Be careful not to damage the belt web-
bing or hardware. If the belt webbing or
hardware is damaged, replace it.
!
Check to make sure that the belt is properly
locked and that the belt is not twisted.NOTE:Seat belt reminder light comes and stays on
until the seat belt is fastened when the
ignition key is turned "ON" or "START".
And, the warning chime will also sound for
about 6 seconds.B190A01Y-AATSEAT BELTS-Front Passenger and Rear
Seat 3-Point System with Combination
Locking Retractor:
To Fasten Your BeltCombination retractor type seat belts are in-
stalled in the rear seat positions to help accom-
modate the installation of child restraint sys-
tems. Hyundai strongly recommends that chil-
dren always be seated in the rear seat. NEVER
place any infant restraint system in the front
seat of the vehicle.
This type of seat belt combines the features of
both an emergency locking retractor seat belt
and an automatic locking retractor seat belt. To
fasten your seat belt, pull it out of the retractor
and insert the metal tab into the buckle. There
will be an audible "click" when the tab locks into
the buckle. When not securing a child restraint,
xgflhma-1.p656/16/04, 3:02 PM 21
ProCarManuals.com

1FEATURES OF YOUR HYUNDAI50
WINDSHIELD WIPER AND WASHER
SWITCH
Mist Wiper OperationIf a single wipe is desired in mist, push the MIST
operation switch at the end of the windshield
wiper and washer control lever.
B350B01Y-GATWindshield Washer OperationTo use the windshield washer, pull the wiper/
washer lever toward the steering wheel. When
the washer lever is operated, the wipers auto-
matically make two passes across the wind-
shield. The washer continues to operate until
the lever is released.NOTE:o Do not operate the washer more than 15
seconds at a time or when the fluid
reservoir is empty.
o In icy or freezing weather, be sure the
wiper blades are not frozen to the glass
prior to operating the wipers.
o In areas where water freezes in winter,
use windshield washer antifreeze.
B350B01LB350B02L
B350A01A-AATThe windshield wiper switch has three posi-
tions:
1. Intermittent wiper operation
2. Low-speed operation
3. High-speed operationNOTE:To prevent damage to the wiper system, do
not attempt to wipe away heavy accumula-
tions of snow or ice. Accumulated snow
and ice should be removed manually. If
there is only a light layer of snow or ice,
operate the heater in the defrost mode to
melt the snow or ice before using the wiper.
B350A01L1
2
3
xgflhma-1.p656/16/04, 3:03 PM 50
ProCarManuals.com

1
FEATURES OF YOUR HYUNDAI
51
!
B350B01B-GATAuto Wiper Operation
(If Installed)
B350B03L
When the windshield wiper switch is placed in
the "AUTO" position, the rain sensor located on
the upper end of windshield glass senses the
amount of rainfall and controls for the appropri-
ate length of the intervals between wipes appro-
priately.NOTE:If there is heavy accumulation of snow or
ice on the windshield glass, there will be a
10 minute waiting period prior to the opera-
tion of the windshield wipers.
Rain Sensor
WARNING:
When the ignition switch is on and the
windshield wiper switch is placed in the
"AUTO" mode, please use caution in the
following cases to avoid any hand injury:
As the wiper system may automatically
activate, the fingers or hand might be caught
in the wiper.
o Do not touch the upper end of the wind-
shield glass facing the rain sensor.
o Do not wipe the upper end of the wind-
shield glass with a cloth.
o Do not put pressure on the windshield
glass.
B350C01L-AATAdjustable Intermittent Wiper OperationTo use the intermittent wiper feature, place the
wiper switch in the "INT" position. With the
switch in this position, the interval between
wipes can be varied from approximately 1 to 18
seconds by turning the interval adjuster barrel.
This is also varied automatically depending on
your road speed.
B350C01L
xgflhma-1.p656/16/04, 3:03 PM 51
ProCarManuals.com

1FEATURES OF YOUR HYUNDAI54
INSTRUMENT PANEL LIGHT
CONTROLB410A01A-AAT(RHEOSTAT)
o DRIVING TIME - This mode indicates the
total time from the starting of the vehicle to the
ignition key "OFF" after resetting. When the
"RESET" switch is pushed, it will initialize to
0:00.RESETPushing "RESET" more than 1 second to initial-
ize the displayed information such as average
speed and driving time.
B400B06L-1
Driving time symbol
Driving time
B410A01L
o AVERAGE SPEED - This mode indicates
the average speed from the starting of the
vehicle to the ignition key "OFF". When the
ignition key is "OFF", it will initialize to 0 mph
(0 km/h).
B400B02L-A
Average speed symbol
Average speed
The instrument panel lights can be made brighter
or dimmer by turning the instrument panel light
control knob.
xgflhma-1.p656/16/04, 3:03 PM 54
ProCarManuals.com

1FEATURES OF YOUR HYUNDAI80
NOTE:o It should be noted that prolonged opera-
tion of the heating system in " " mode
will give rise to misting of the windshield
and side windows and the air within the
passenger compartment will become
stale. In addition prolonged use of the air
conditioning with the " " mode selected
may result in the air within the passenger
compartment becoming excessively dry.
o When the ignition switch is turned "ON",
the air intake control will change to " "
mode (regardless of switch position).
This is normal operation.
HEF030 B670D01L-AAT
Air Flow ControlThis is used to direct the flow of air. Air can be
directed to the floor, dashboard outlets, or
windshield. Five symbols are used to represent
Face, Bi-Level, Floor, Floor-Defrost and De-
frost air position.Face-Level
Selecting the "Face" mode will cause air to be
discharged through the face level vents.
B670D02L-1
xgflhma-1.p656/16/04, 3:04 PM 80
ProCarManuals.com

1
FEATURES OF YOUR HYUNDAI
87
B970C02L-AATAutomatic Operation
2. Push the "TEMP" button to set the desired
temperature.
The temperature will increase to the maxi-
mum 90°F(32°C) by pushing on the button.
Each push of the button will cause the tem-
perature to increase by 1°F (0.5°C).
The temperature will decrease to the mini-
mum 62°F(17°C) by pushing on the button.
Each push of the button will cause the tem-
perature to decrease by 1°F (0.5°C). The FATC (Full Automatic Temperature Con-
trol) system automatically controls heating and
cooling as follows:
1. Push the "AUTO" switch. The indicator light
will illuminate confirming that the Face, Floor
and/or Bi-Level modes as well as the blower
speed and, air conditioner will be controlled
automatically.
NOTE:If the battery has been discharged or dis-
connected, the temperature mode will reset
to centigrade degrees.
This is a normal condition and you can
change the temperature mode from centi-
grade to farenheit as follows;
Press the TEMP button down 3 seconds or
more with the AMB button held down. The
display shows that the unit of temperature
is adjusted to centigrade or fahrenheit.
(°C
→ →→ →
→ °F or °F
→ →→ →
→ °C)NOTE:Never place anything over the sensor which
is located on the instrument panel to en-
sure better control of the heating and cool-
ing system.
Photo sensor
B970C01LB970C02L
B970C03L
xgflhma-1.p656/16/04, 3:04 PM 87
ProCarManuals.com