2005 HUMMER H2 clock

2. Remove the two
screws from the rear
lamp assembly
and remove the rear
lamp assembly.
3. Turn the bulb socket counterclockwise to remove it
from the taillamp housing.4. Pull the bulb straight
out from the socket.
5. Press a new bulb into the socket, insert it into the
taillamp housing and turn the socket
counterclockwise until it is locked in place.
6. Reinstall the rear lamp assembly and tighten
the screws.
Your vehicle may have a taillamp in the bumper. To
replace it, do the following:
5-51

1. Locate the affected
taillamp which is
behind and under
the bumper.
2. Turn the bulb socket counterclockwise and remove
it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Put the new bulb into the bulb socket.
5. Put the bulb socket into the lamp housing and turn
it clockwise to lock it.Replacement Bulbs
Exterior Lamp Bulb Number
Back-up Lamp 3156
Daytime Running Lamp (DRL) 4114K
Front Turn Signal and
Parking Lamp4157K or 3157KX
Low-Beam and High-Beam
Headlamps9007
Rear Taillamp and Stoplamp 3057
Rear Taillamp in Bumper 3057
Rear Turn Signal Lamp 3156
Roof Marker Lamp 168
For replacement bulbs not listed here, please consult
your dealer.
5-52

When you have a at tire, use the following example as
a guide to assist you in the placement of wheel blocks.
The following steps will tell you next how to use the jack
and change a tire.Removing the Spare Tire and Tools
Removing the Tools
SUV
The equipment you’ll need is behind and to the side of
the driver’s side second row seat. To remove the
equipment, do the following:
1. Fold the driver’s side second row seat down.
See60/40 Split Bench Seat on page 1-7for
more information.
2. Turn the wingnut (A)
counterclockwise to
release the jack.
3. Turn the wingnut (B), which holds the jack tool kit,
counterclockwise to release it.
5-71

Removing the Inside-Mounted
Spare Tire
The spare tire and wheel blocks are stored in the rear
cargo area. You will need to remove the tire cover to get
to them.
A. Spare or Flat Tire
B. Receiver Extension (If Equipped) Not used for tire
changing procedure. See “Receiver Extension” under
If You Are Stuck: In Sand, Mud, Ice or Snow on
page 4-52.
C. Tire Retainer Plate
D. Nut
E. Wheel Blocks1. Remove the wheel blocks from the tire retainer
plate by turning the wingnut counterclockwise.
2. Place the at end of the wheel wrench through the
hole in the spanner wrench.
5-75

3. Place the end of the
spanner wrench on the
nut and then turn
the wheel wrench
counterclockwise to
loosen the nut
holding the tire to
the carrier.
4. Pull off the tire retainer plate and set it aside.
Remove the spare tire from the wheel carrier.
5. Put the spare tire near the at tire.The tools you’ll be using to nish changing a at tire are
the following:
A. Jack
B. Wheel Blocks
C. Jack HandleD. Jack Handle
Extension
E. Wheel Wrench
F. Ratchet
Before proceeding, be sure to set the wheel blocks at
the appropriate tires as shown previously.
5-76

5. Turn the ratchet counterclockwise to loosen the
wheel nuts.
6. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
7. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.The tools you’ll be using to nish changing a at tire
include the following:
A. Jack
B. Wheel Blocks
C. Jack HandleD. Jack Handle
Extension
E. Wheel Wrench
F. Ratchet
Before proceeding, be sure to set the wheel blocks at
the appropriate tires as shown previously.
5-78

Removing the Flat Tire and
Installing the Spare Tire
1. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and gently pry the
center cap out.
2. Slide the ratchet onto the wheel wrench with the
DOWN mark facing you.
3. Turn the ratchet counterclockwise to loosen the
wheel nuts. Don’t remove them yet.
You will now need to jack the vehicle up using the
instructions following.
5-79

5. Turn the ratchet clockwise to raise the jack head to
the lifting point.
Front Flat Tire:Position
the jack under the vehicle
on the frame behind
the at tire where the
frame sections overlap.
See the graphic following
for an approximate
measurement of the jack
location on the frame.
Front Flat Tire
X = 28.5 inches (72.0 cm)
5-81