CLIMATE CONTROL
Dual Zone Automatic Temperature Control (IF EQUIPPED)
Driver and Passenger Side TemperatureSet desired cabin temperature with the blue and red
buttons. Press to increase or decrease the temperatureon the driver or passenger side of the cabin.
Dual Control(IF EQUIPPED)Press DUAL to engage/disengage separate
passenger side temperature control. For controls
without a DUAL button, press and hold AUTO toengage/disengage separate passenger sidetemperature control.
Automatic Operation
Set desired cabin temperature. Then press AUTO for
full automatic operation. The system will automaticallyadjust airflow temperature, front fan speed, airflowdirection, A/C, and recirculated air based on theselected temperature to heat or cool the vehicle to thedesired temperature as soon as possible.
Defogging/DemistingPress Defrost to distribute outside air through the
windshield defroster vents and demister vents. Toreduce humidity build up in the vehicle, do not drivewith the Climate Control turned off. Also, do not drivewith recirculated air selected unless the A/C is operating.
One Button Air Flow Direction Control (if equipped)Press repeatedly to select desired airflow direction.
Heated Seats
Press to cycle through available settings of highheat (2 lights), low heat (1 light), and off (no lights).
Rear
Press to give rear passenger control of the auxiliaryclimate system. Press again to turn system off.
Rear Temperature Control
Press to increase or decrease temperature to therear of the vehicle.
Rear Fan Speed Control
Press to increase or decrease the rear fan speed.
22
21
20
19
18
17
16
15
1413
1
2
34
5
67
8
9
10
11
12
17
19
1918
20
21
2213
1416
15
Max A/C Operation
Automatic Operation: Press AUTO for fullautomatic operation. Do not override A/C or
recirculated air. Set the temperature to 60°F (15.5°C).
Override Operation: Select air distribution. Select
A/C and recirculated air. Use recirculated air with
A/C to provide colder airflow. Set temperature to
60°F (15.5°C). Set to highest front fan speed
initially, then adjust to maintain comfort.
Manual Override Operation
Set desired cabin temperature. Adjust any of
the following for personal comfort preferences:front fan speed, airflow direction, A/C, and
recirculated air. Front fan speed, A/C, and
recirculated air overrides will not turn off the AUTOindicator light. Airflow direction overrides will turn off
the AUTO indicator light.
ONE| HEADLAMP CONTROL
Turning the headlamp control clockwise to the first position turns on the parking lamps,
instrument panel lamps, license plate lamps, and the tail lamps. Continuing to turn the
headlamp control to the second position turns on the headlamps. To use the autolamplight sensitive, automatic on off control for the headlamps, turn the headlamp control
counterclockwise. To turn autolamps off, turn the control clockwise to the OFF position.
To activate the high beams, simply pull the turn signal lever towards you to the second detent. Pull the
lever towards you again to deactivate them. Use the same lever to activate the “Flash to Pass” feature.Pull the lever towards you to the first detent to activate and release it to deactivate.
TWO | FOGLAMP CONTROL (IF EQUIPPED)
With the ignition on, the foglamps can be turned on when the headlamp control is in the
parking lamp, headlamp, or autolamp position, and the high beams are not on. Simply pullthe headlamp control towards you to turn on the foglamps. The foglamp indicator light willilluminate. The foglamps will not operate when the high beams are activated.
THREE | PANEL DIMMER
Use to adjust the brightness of the instrument panel and all applicable switches in the
vehicle during headlamp and parking lamp operation. Move the control to the full uprightposition, past the detent, to turn on the interior lamps.
FOUR| HOOD RELEASE
To open the hood, pull the hood release handle under the bottom of the instrument panel,
near the steering column. Go to the front of the vehicle and release the auxiliary latchlocated under the front center of the hood. Use the prop rod to support the raised hood.
FIVE| SPEED CONTROL
For your speed control to work, you must press and release the ON button. Pressing and
releasing the OFF button, disengages the system and turns it off. To set a desired speed,accelerate to the desired speed, press and release the SET+ button, then take your foot off
the accelerator pedal. You can increase speed using speed control by pressing and
releasing the SET+ button until you reach the desired speed; increasing speed by 1 mph (1.6
km/h) with each tap. You can decrease speed in the same way using the SET button.
Pressing the RSM
INSTRUMENT PANEL AND INTERIOR FEATURES
