CLIMATE CONTROL
DRIVER AND PASSENGER SIDE
TEMPERATURE
Set desired cabin
temperature with the
or blue and red
buttons. Press for
driver’s side, forpassenger’s side.Recommended settings
72°F (22°C) to 75°F (24°C).
DUAL CONTROL (IF EQUIPPED)Press DUAL to
engage/disengageseparate passenger sidetemperature control.
For controls without a
DUAL button, press
and hold AUTO toengage/disengageseparate passenger sidetemperature control.
AUTOMATIC OPERATIONSet desired cabin
temperature.
Press AUTO button for
full automatic operation.The system willautomatically adjust airflowtemperature, fan speed,airflow direction, A/C, andrecirculated air based onthe selected temperature toheat or cool the vehicle to
the desired temperature asquickly as possible.
MAX A/C OPERATIONAUTOMATIC OPERATION:Press AUTO button for
full automatic operation.
Do not override A/C or
recirculated air. Settemperature to 60°F
(15.5°C).
OVERRIDE OPERATION:Select air distribution.
Select A/C and
recirculated air. Use
recirculated air with A/C
to provide colder airflow.Set temperature setting
to 60°F (15.5°C).
Initially set to highest fan
speed , then adjust tomaintain comfort.
MANUAL OVERRIDE OPERATION Press to set desired
cabin temperature.
Adjust any of the following
for personal comfort
preferences: fan speed,
airflow direction, A/C,
and recirculated air.
Fan speed, A/C, and
recirculated air overrides
will not turn off the AUTOindicator light. Airflowdirection overrides will turn
off the AUTO indicator light.
ONE BUTTON AIRFLOW
DIRECTION CONTROL
(IF EQUIPPED)Press repeatedly to
select airflow direction.
DEFOGGING/DEMISTINGPress to distribute
outside air through thewindshield defroster ventsand demister vents.
To reduce humidity
buildup in the vehicle,do not drive with theClimate Control turned off. Also, do not drive withrecirculated air selected
unless A/C is operating.
HEATED SEATS (IF EQUIPPED)Press to cycle through
available settings of highheat (2 lights), low heat (1 light), and off (no lights).6
3
7
5
1
5
98
7
2
2
1
210
10
4141
DUAL ZONE AUTOMATIC CLIMATE CONTROL WITH HEATED SEATS (IF EQUIPPED)SPLIT FOLDING
REAR SEAT
One or both rear seat backs
can be folded down to provideadditional cargo space.
To lower the seat backs, pull
the strap located on theoutboard side of the seat backto release it, and then fold theseat back down.
Note: When raising the seat
back(s), make sure to firmlylock into place and tug
forward to assure that it is fully latched.
SEATING
14
10
3
789656
2
789
FRONT PASSENGER
FOLD FLAT SEAT BACK
(IF EQUIPPED)The front passenger seat
back can be folded down toa horizontal position to allowroom for a long load. Ensurethat the seat is in therearmost position and thehead restraint is fully down,prior to pulling the straplocated on the back of theseat back.
HEADLAMP CONTROLTurning the headlamp control
clockwise to the first positionturns on the parking lamps,instrument panel lamps,license plate lamps, and thetail lamps. Continuing to turnthe headlamp control to thesecond position turns on the
headlamps. To use theautolamp light sensitive,automatic on off control forthe headlamps, turn theheadlamp control
counterclockwise. To turnautolamps off, turn thecontrol clockwise to the OFF
position. To activate the highbeams, simply pull the turnsignal lever towards you tothe second detent. Pull thelever towards you again todeactivate high beams. Usethe same lever to activate the
“Flash to Pass” feature. Pullthe lever towards you to thefirst detent to activate and release it to deactivate.
1
PANEL DIMMERUse to adjust the brightness
of the instrument panel andall applicable switches in thevehicle during headlamp andparking lamp operation.Move the control to the fullupright position, past detent,to turn on the interior lamps.
2
FOGLAMP CONTROL(IF EQUIPPED)With the ignition on, the
foglamps can be turned onwhen the headlamp control is in the parking lamp,headlamp or autolampposition, and the high beamsare not on. Simply pull theheadlamp control toward youto turn on the foglamps. Thefoglamp indicator light willilluminate. The foglamps willnot operate when the highbeams are activated.
3
WINDSHIELD WIPER
WASHER
The multifunction lever
controls the windshield wipermodes, speeds, and the
windshield washer. Forintermittent operation, movethe control up one position.
You can then adjust the
rotary control to the desired
interval speed. For normal orlow wiper speed, move thecontrol up two positions from
OFF. For high speedoperation, move the control
up three positions from OFF.
For windshield washercontrol, pull the end of the
lever toward you. With aquick pull and hold, thewipers will swipe three times
with washer fluid. With a longpull and hold, the wipers willactivate washer fluid for up toten seconds.
4
