2005 DODGE RAM 1500 GAS open hood

Seats................................107
▫40-20-40 Front Seat....................108
▫Reclining Seats.......................109
▫Adjustable Head Restraints..............109
▫Manual Rotary Lumbar Support
Adjustment — If Equipped..............110
▫Power Seats — If Equipped..............111
▫Heated Seats — If Equipped.............112

To Open And Close The Hood.............113

Lights...............................115
▫Interior Lights.......................115
▫Battery Saver........................116
▫Headlamp Delay — If Equipped..........117▫Headlights, Parking Lights, Panel Lights.....117
▫Daytime Running Lights
(Canada And Fleet Vehicles Only)..........118
▫Lights-On Reminder...................118
▫Fog Lights — If Equipped...............118
▫Cargo Light.........................119

Multifunction Control Lever...............119
▫Turn Signals.........................119
▫Passing Light........................120
▫High Beam / Low Beam Select Switch......120
▫Windshield Wipers....................121
▫Windshield Washers...................122

Tilt Steering Column....................123
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Each heated seat switch has two settings (HI and LOW).
Press the switch once to obtain the desired heating
position and press a second time in the same direction to
turn the heated seats OFF. If you do not purposefully
turn the switch OFF, the heating element in the seat will
remain activated until the ignition is turned off. The
indicators on the switch will illuminate when the heated
seats are in the (HI or LOW) position. Flashing telltale
lights on the switch indicate that the Heated Seat system
needs servicing.TO OPEN AND CLOSE THE HOOD
To open the hood, two latches must be released. First pull
the hood release lever located below the steering wheel at
the base of the instrument panel. Once the hood is
released you must reach into the opening beneath the
center of the grille and push up the latch to release the
safety catch before raising the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
3

To set the variance: Turn the ignition ON and set the
display to “Compass/Temperature.” Press the RESET
button approximately five seconds. The last variance
zone number will be displayed. Press the STEP button to
select the new variance zone and press the RESET button
to resume normal operation.
Outside Temperature
Because the ambient temperature sensor is located un-
derhood, engine temperature can influence the displayed
temperature, therefore, temperature readings are slowly
updated when the vehicle speed is below 20 mph (30
km/h) or during stop and go driving.
GARAGE DOOR OPENER — IF EQUIPPED
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at the
push of a button. The Universal Transceiver operates off
your vehicle’s battery and charging system; no batteries
are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137
3

edges of the instrument panel. The demisters also pro-
vide extra air ducts for circulation. They are in operation
whenever the Floor, Mix or Defrost modes are in use.
NOTE:When you turn off the engine you may hear a
hissing sound from under the hood for a short period of
time. This is a normal condition that occurs if the air
conditioning system has been on. It is not an indication of
a problem with the air conditioning system.
Operating Tips
Fast Cooldown
For a fast cooldown, turn the blower fan rotary knob to
the extreme right position, turn the mode control to the
panel fresh position, press the snowflake button to turn
on the air conditioning, and drive with the windows
open for the first few minutes. Once the hot air has been
expelled, close the windows and press the Recirculation
pushbutton. When a comfortable condition has beenreached, choose a mode position and adjust the tempera-
ture control slide and blower speed as necessary to
maintain comfort. For high humidity conditions it may
be necessary to remain in the Recirculation mode to
maintain comfort.
Window Fogging
Windows will fog on the inside when the humidity inside
the vehicle is high. This often occurs in mild or cool
temperatures when it’s rainy or humid. In most cases
turning on the Air-conditioning (pressing the snowflake
button) will clear the fog. Adjust the temperature control,
air direction and blower speed to maintain comfort.
As the temperature gets colder it may be necessary to
direct air onto the windshield by using MIX Mode
position on the control. Adjust the temperature control
and blower speed to maintain comfort. Higher blower
UNDERSTANDING YOUR INSTRUMENT PANEL 219
4

If the engine has been flooded, it may start to run, but not
have enough power to continue running when the key is
released. If this occurs, continue cranking with the accel-
erator pedal pushed all the way to the floor. Release the
accelerator pedal and the key once the engine is running
smoothly.
If the engine shows no sign of starting after two 15
second periods of cranking with the accelerator pedal
held to the floor, the normal starting procedure should be
repeated.
WARNING!
Never pour fuel or other flammable liquids into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in a flash fire causing
serious personal injury.
Engine Block Heater— If Equipped
The engine block heater warms the engine coolant and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 volt AC electrical outlet with
grounded, three-wire extension cord.
The engine block heater cord is routed under the hood to
the right side of the vehicle and held to the body with
removable clips.
WARNING!
Remember to disconnect the cord before driving.
Damage to the 110-115 volt electrical cord could
cause electrocution.
STARTING AND OPERATING 231
5

WARNING!
The warning words “DO NOT OPEN HOT” on the
radiator pressure cap are a safety precaution. Heat
causes pressure to build up in the cooling system. To
prevent scalding or injury, do not remove the pres-
sure cap.
Hoses And Vacuum/Vapor Harnesses
Inspect surfaces of hoses and nylon tubing for evidence
of heat and mechanical damage. Hard or soft spots,
brittle rubber, cracking, tears, cuts, abrasions, and exces-
sive swelling indicate deterioration of the rubber.
Pay particular attention to those hoses nearest to high
heat sources such as the exhaust manifold. Inspect hose
routing to be sure hoses do not come in contact with any
heat source or moving component which may cause heat
damage or mechanical wear.Insure nylon tubing in these areas has not melted or
collapsed.
Inspect all hose connections such as clamps and cou-
plings to make sure they are secure and no leaks are
present.
Components should be replaced immediately if there is
any evidence of wear or damage that could cause failure.
Brake System
Power Disc Brakes (front and rear)
Disc brakes do not require periodic adjustment.
Brake Master Cylinder
The fluid level of the master cylinder should be checked
when performing under the hood service, or immedi-
ately if the brake system warning lamp indicates system
failure.
372 MAINTAINING YOUR VEHICLE

Transfer Case........................... 375
Fluid............................... 406
Transmission
Automatic........................232,377
Fluid............................... 406
Maintenance.......................376,377
Manual.....................229,238,239,376
Shifting..........................232,240
Transmitter, Garage Door Opener............ 137
Tread Wear Indicators.................... 275
Trip Computer.......................... 130
Trip Odometer.......................171,172
Turn Signals................... 119,166,391,395
Underhood Fuses........................ 389
Universal Transmitter..................... 137
Variance, Compass....................... 136
Vehicle Identification Number................ 6Vehicle Loading......................265,293
Vehicle Modifications/Alterations.............. 7
Vehicle Storage......................... 390
Voltmeter............................. 166
Warning Lights (Instrument Cluster Description) . 165
Warnings and Cautions..................... 5
Warranty Information..................... 430
Washers, Windshield..................122,366
Washing Vehicle......................... 385
Wheel Alignment and Balance............... 277
Wheel and Wheel Trim.................... 387
Wheel Changing........................ 326
Wheel Mounting........................ 327
Wheel Nut Torque....................332,336
Wind Buffeting.......................33,146
Window Airbag.......................... 54
Window Fogging........................ 219
Windows.............................. 31
450 INDEX