2005 DODGE MAGNUM open hood

▫Lumbar Support.......................85
▫Heated Seats—If Equipped...............85
▫Head Restraints.......................86
▫Folding Rear Seat......................87

Adjustable Pedals—If Equipped...........88

To Open And Close The Hood.............89

Lights...............................91
▫Overhead Console Map/Reading Lights......91
▫Interior Lights........................91
▫Headlight Switch......................92
▫Multi-Function Lever....................93
▫Headlights, Parking Lights, Instrument Panel
Lights..............................93
▫Daytime Running Lights (Canada Only)......94
▫Lights-On Reminder....................94
▫Headlight Time Delay...................94▫Fog Lights—If Equipped................94
▫Turn Signals..........................94
▫Highbeam/Lowbeam Select Switch..........95
▫Flash To Pass.........................95

Windshield Wipers And Washers...........95
▫Windshield Wiper Operation—Front ........95
▫Windshield Wiper Operation—Rear........96
▫Windshield Washers....................96
▫Adding Washer Fluid...................97

Tilt/Telescoping Steering Column...........98

Traction Control System (TCS)—If Equipped..98

Brake Assist System (BAS)—If Equipped....100

Electronic Stability Program (ESP)—If
Equipped
............................101
▫Synchronizing ESP....................103

Electronic Speed Control.................103
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Press the switch rearward to move the pedals rearward
(toward the driver).
•The pedals can be adjusted with the ignition OFF.
•The pedals can be adjusted while driving.
•The pedalscannotbe adjusted when the vehicle is in R
(Reverse) or when the Speed Control is ON.
CAUTION!
Do not place any article under the adjustable pedals
or impede its ability to move as it may cause damage
to the pedal controls. Pedal travel may become
limited if movement is stopped by an obstruction in
the adjustable pedal’s path.
TO OPEN AND CLOSE THE HOOD
Two latches must be released to open the hood. First, pull
the hood release lever located under the left side of the
instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89
3

Next, move to the outside of the vehicle and push the
safety catch to the left. The safety catch is located under
the center front edge of the hood.
Use the hood prop rod to secure the hood in the open
position.To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open approximately 6
inches (15 cm) and then drop it. This should secure both
latches. Never drive your vehicle unless the hood is fully
closed, with both latches engaged.
WARNING!
If the hood is not fully latched, it could fly up when
the vehicle is moving and block your forward vision.
You could have a collision. Be sure all hood latches
are fully latched before driving.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Cooling System
Inspection
WARNING!
•When working near the radiator cooling fan, turn
the ignition key to the OFF position. The fan is
temperature controlled and can start at any time
when the ignition key is in the ON position.
•You or others can be badly burned by hot coolant
or steam from your radiator. If you see or hear
steam coming from under the hood, don’t open
the hood until the radiator has had time to cool.
Never try to open a cooling system pressure cap
when the radiator is hot.
Coolant Checks
Coolant protection checks should be made every 12
months (prior to the onset of freezing weather, where
applicable). If coolant is dirty or rusty in appearance, the
system should be drained, flushed and refilled with fresh
coolant. Check the front of the A/C condenser for anyaccumulation of bugs, leaves, etc. If dirty, clean by gently
spraying water from a garden hose vertically down the
face of the condenser.
Check the cooling system hoses for brittle rubber, crack-
ing, tears, cuts and tightness of the connection at the
bottle and radiator. Inspect the entire system for leaks.
Cooling System—Drain, Flush and Refill
At the intervals shown in the appropriate maintenance
schedule, the system should be drained, flushed and
refilled.
If the solution is dirty or contains a considerable amount
of sediment, clean and flush with a reliable cooling
system cleaner. Follow with a thorough rinsing to remove
all deposits and chemicals. Properly dispose of old
antifreeze solution.
Selection Of Coolant
Use only the manufacturers recommended coolant, refer
to Recommended Fluids, Lubricants and Genuine Parts
for correct coolant type.
MAINTAINING YOUR VEHICLE 295
7

LIGHT BULBS—Exterior Bulb Number
Low Beam Headlamp.....................9006
High Beam Headlamp....................9005
Front Park/Turn Lamp...................3457A
Front Fog Lamp—If Equipped. . . 9145/H10 (Serviced at
Dealer)
Front Sidemarker........194NA (Serviced at Dealer)
Tail/Stop/Turn Lamp..............3157KP27/7W
Rear Sidemarker.................3757APY27/7W
Backup Lamp......................921/W16W
Center High Mount Stop Lamp (CHMSL)....... LED
License.............................. W5W
BULB REPLACEMENT
Low Beam Headlamp, High Beam Headlamp, and
Park/Turn Lamp
•
Open the hood.
•Twist the appropriate bulb socket assembly counter-
clockwise and pull out. Pull the bulb out of the socket
assembly.
NOTE:Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs on driver’s side head-
lamp assembly.
•Replace the bulb and push into socket assembly.
Reinstall the socket assembly, and turn clockwise.
314 MAINTAINING YOUR VEHICLE