2005 DODGE DURANGO belt

SEATS
Front Seat Manual Seat Adjustment
The adjusting lever is at the front of the seat, near the
floor. Lift the lever and move the seat to the desired
position. Release the bar to lock the seat into position.
Using body pressure, move forward and rearward on the
seat to be sure the seat adjusters have latched.
WARNING!
Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
properly adjusted and you could be injured. Adjust
any seat only while the vehicle is parked.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Seats Manual Seat Recliners
The bucket seats are equipped with recliners. The reclin-
ing mechanism is operated by a lever located on the right
side of the passenger’s seat and the left side of the
driver’s seat. To recline, lean forward slightly before
lifting the lever, then push back to the desired position
and release the lever. Lean forward and lift the lever to
return the seatback to its normal position. Using body
pressure, lean forward and rearward on the seat to be
sure the seatback is locked.
WARNING!
Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt and
be seriously or even fatally injured. Use the recliner
only when the vehicle is parked.
Manual Lumbar Support Adjustment — If
Equipped
The manual lumbar support adjustment lever is located
on the right side of the driver’s seat and on the left side
of the passenger’s seat. Moving the lumbar control lever
fore and aft increases or decreases the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103
3

WARNING!
The 20% seatback contains the center shoulder belt.
A 20% seatback that is not fully latched in the
upright position will not protect you properly.
To Tumble the 40% seat, fully raise the lever on the side
of the seat to release the floor latches and tumble the seat.
NOTE:The seatback must be fully folded into the down
position to allow the lever to be raised enough to release
the floor latches.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:Before returning the second row 40% seats to
their upright position, always snap the third row seat
flipper panel(s) back to the third row seat first.
NOTE:The seat belt buckles are hinged to fold with the
seat back.
WARNING!
Do not sit in the third row seat unless the cushion
and back are properly engaged. Proper engagement
can be verified by pushing/pulling on the upright
seatback. The seatback will not move unless prop-
erly engaged.
Do not sit in the 3rd row seat with the second row
seatback(s) folded or tumbled. In a collision, you
could slide under the seat belt and be seriously or
even fatally injured.
Third Seat 50/50 Split Seat — If Equipped
To Fold The Seat(s)
Pull up the release handle(s) and move the seatback
forward. This can be performed from either the front or
rear of the third row seats. The seatback and seat cushion
move simultaneously into load floor position and rests
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3

on the floor behind the second row seats.The seat belt
buckles are hinged and fold with the seatbacks.
To Achieve Maximum Cargo Capacity
Pull the release handles and strap on the second row
seats and fold flat. After folding the third row seats,unsnap the flipper panels on the back of the third row
seatbacks and flip the panels onto the backs of the second
row seats.
NOTE:Before returning the second row 40% seats the
upright position, always reposition the flipper panel(s)
and snap onto the third row seat first.
NOTE:The seat belt buckles are hinged to fold with the
seat backs.
To Return The Seat(s) To An Upright Position
If required, unsnap the strap(s). Pull on the seatback from
the rear of the vehicle to reposition the seat(s) to an
upright position. Reposition strap onto the hook and loop
material on the seat back and snap strap(s).
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
Do not sit in the third row seat unless the cushion
and back are properly engaged. Proper engagement
can be verified by pushing/pulling on the upright
seatback. The seatback(s) will not move unless prop-
erly engaged.
Do not sit in the 3rd row seat(s) with the second row
seatback(s) folded or tumbled. In a collision, you
could slide under the seat belt and be seriously or
even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113
3

Memory Position Recall
NOTE:
•The driver’s seat belt must be unbuckled to recall
memory positions.
•The vehicle must be in Park to recall memory posi-
tions.
•Not all motors may be moved at one time. Please refer
to the 8-way power seat description.
To recall the memory settings for driver one, press
memory button number 1 on the driver’s door or the
Unlock button on the Remote Keyless Entry transmitter
linked to memory position 1.
To recall the memory setting for driver two, press
memory button number 2 on the driver’s door or the
Unlock button on the Remote Keyless Entry transmitter
linked to memory position 2.A recall can be cancelled by pressing any of the memory
buttons on the drivers door during a recall (S, 1, or 2), or
pressing any one of the power seat buttons, or pressing
the adjustable pedals button, or pressing either the LOCK
or UNLOCK button on the remote keyless entry trans-
mitter when not in the ignition switch. When a recall is
cancelled, the driver’s seat, and the pedals stop moving.
A delay of one second will occur before another recall can
be selected.
NOTE:A chime sound may be heard if Setting Memory
was inhibited for any reason.
To Disable A Transmitter Linked to Memory
1. Turn the ignition switch to the OFF position and
remove the key.
2. Press and release the memory SET (S) button located
on the driver’s door.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Adjustment
1. Position the driver seat so that you are at least 10
inches (254 mm) away from the airbag located in the
center of the steering wheel.
2. Fasten and adjust the seatbelts.
3. Move the adjustable pedal switch, located to the left of
the steering column near the parking brake release, up to
move the pedals toward the driver or down to move the
pedals away from the driver.
4. The pedalscannotbe adjusted when the vehicle is in
R (Reverse) or when the Speed Control is SET.
CAUTION!
Do not place any article under the adjustable pedals
or impede its ability to move as it may cause damage
to the pedal controls. Pedal travel may become
limited if movement is stopped by an obstruction in
the adjustable pedal’s path.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131
3