Page 272 of 462
Downloaded from www.Manualslib.com manuals search engine 266
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY - RHZ
Remove:
- The fixings of the pipe linking the power steering pump with the rotary valve.
- The clutch lower closing plate.
- Lock the engine flywheel, using tool [6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
- The accessories pulley (9), using tool [8].
- Tool [6].
- The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
- The bearing shell fitting (10).
- The nut (12).
- Screws (11).
- The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
- The intermediate timing cover.
- The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA - XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 266
Page 321 of 462
Downloaded from www.Manualslib.com manuals search engine 315
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFU - NFU - RFN - RFJ - RFK - 9HX - 9HY - 9HZ - RHR
NOTE:All the clutches are «push»type with hydraulic control.
NOTE:The DV6TED4and DW10BTED4engines are equipped with a double damping flywheel (DVA).
Description.
The declutch control has a declutch fork with a ball-joint on the axis.
(1)The ball-joint is screwed into the clutch casing
(2) Declutch fork
(3)Clutch casing
(4)Bearing
(5) Clutch plate
The clutch control slave cylinder(7)is fixed by two screws (6) into the exterior of the clutch casing.
B2BP047C
B2CP3FAC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 315
Page 322 of 462
Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFW - NFU - NFV - 6FZ - RFN - 8HX - 8HZ - 9HY - 9HZ - WJY - RHY - RHZ
NOTE:All the clutches are «push»type with hydraulic control.
Description.
The declutch control has a declutch fork mounted on a ball-joint.
(1)The ball-joint is screwed into the clutch casing
(2)Declutch fork
(3)Clutch casing
(4)Bearing
(5)Clutch plate
The clutch control slave cylinder (7)is fixed by two screws (6)onto the exterior of the clutch casing.
T
ightening torques (m.daN).
Fixing of clutch plate/engine flywheel: 2 ± 0,2.
Fixing of clutch control slave cylinder / clutch housing: 2 ± 0,25.
Fixing of engine flywheel/crankshaft
Pre-tightening: 1,75 ± 0,2.
Angular tightening: 75° ± 5°.
Checking torque: 6,3 ± 2,2.
B2BP047CB2BP05SC
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 316
Page 326 of 462
Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(6)Clutch bearing guide screw: 1 ± 0,1
(7)Bearing retaining clip screw: 1,8 ± 0,2
Intermediate plate fixing: 5 ± 0,5
Hydraulic clutch slave cylinder fixing: 3 ± 0,3
B2CP3ZJD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 320
Page 327 of 462
Downloaded from www.Manualslib.com manuals search engine 321
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(8)Gearbox support shaft nut: 6,5 ± 0,6
(9) Screws fixing gearbox support on body: 1,9 ± 0,1
(10)Gearbox support plate nut: 2,5 ± 0,2
(11)Nut fixing gearbox support on body: 1,9 ± 0,1
(12)Nut securing rubber bush: 3 ± 0,3
B2CP3ZKC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 321
Page 328 of 462
Downloaded from www.Manualslib.com manuals search engine 322
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX SPECIFICATIONS
Engines: KFW - NFU
Tightening torques (m.daN).
(23) Clutch bearing guide (3 fixing screws): 0,6 ± 0,15
(24)Intermediate plate
(11 fixing screws): 5 ± 0,5
(25)Rear cover
(3 fixing screws): 2,2 ± 0,2
(26)Bearing retaining clip
(4 fixing screws): 1,8 ± 0,2
(27)Secondary shaft nut
(1 nut): 14 ± 1
(28)Gearbox casing
(15 fixing screws): 1,8 ± 0,2
B2CP167P
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 322
Page 335 of 462
Downloaded from www.Manualslib.com manuals search engine 329
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: ML6 GEARBOX
Engine: RHR
Tightening torques (m.daN).
(5)Reverse gear switch: 2,5 ± 0,5
(6)Level plug: 3 ± 0,2
(7)Drain plug: 3 ± 0,3
(8)Differential bearing stop plate screw: 3 ± 0,3
(9)Screw fixing gearbox housing / clutch housing: 3 ± 0,3
(10) 6thgear housing fixing screw: 2 ± 0,2
(11)Differential housing fixing
(screws M8): 1,8 ± 0,3
(12)Differential housing fixing
(screws M10): 4 ± 0,8
B2CP3ZMP
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 329
