2005 Citroen XSARA PICASSO wheel torque

Downloaded from www.Manualslib.com manuals search engine 117
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder block
Crankshaft bearing cap cover.
Tightening method:
Pre-tighten the 10 screws(17)
(from 1 to 10) to1
Pre-tighten the 14 screws (19)
(from 11 to 24) to 0,6
Tighten the2 screws (18)
(inside the flywheel bell housing) to0,8
Slacken the screws (17) by 180°
Tighten the 10screws (17)
(from 1 to 10)to 3
Tighten the screws (17)
(from 1 to 10) by 140°
Tighten the14 screws (19) (from 11 to 24)to 0,8
Engines: 9HY - 9HZ
B1DP1LLD
(17) Bearing cap fixing screws (screws M9)
(18) Crankshaft bearing cap cover screws(screws M6)
(19) Crankshaft bearing cap cover screws (screws M6)
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 117

Downloaded from www.Manualslib.com manuals search engine 127
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Engines9HZ - 9HY
Cylinder head
Camshaft bearing covers
Pre-tightening0,5 ± 0,1
Tightening1 ± 0,1
Exhaust manifold3 ± 0,3
Camshaft pulley
Pre-tightening2 ± 0,2
Angular tightening50°±5°
Cylinder head
Pre-tightening2 ± 0,2
Tightening4 ± 0,5
Angular tightening260° ± 5°
EGR valve1 ± 0,1
Flywheel - Clutch
Flywheel
Pre-tightening3 ± 0,3
Angular tightening90°±5°
Clutch mechanism2 ± 0,2
XSARA PICASSO
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 127

Downloaded from www.Manualslib.com manuals search engine 133
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Flywheel
Flywheel4,8 ± 0,4
Clutch mechanism2 ± 0,2
Lubrication circuit
Oil pump2,3 ± 0,2
Coolant/oil heat exchanger7 ± 0,7
Injection circuit
Injector on cylinder head9 ± 0,9
Diesel fuel heater1,5 ± 0,1
Injection pump2 ± 0,2
Union on injector2,5 ± 0,2
Injection pump pulley2,3 ± 0,2
Cooling circuit
Coolant pump1,5 ± 0,1
Coolant inlet housing1,8 ± 0,1 Engine: WJY
XSARA
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 133

Downloaded from www.Manualslib.com manuals search engine 136
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Flywheel
Flywheel4,8 ± 0,4
Clutch mechanism2 ± 0,2
Lubrication circuit
Oil pump1,6 ± 0,2
Coolant oil heat exchanger7 ± 0,7
Turbocharger lubrication pipe
Engine end4,8 ± 0,4
Turbocharger end2,2 ± 0,2
Injection circuit
Injector fixing flange nut3 ± 0,3
Unions on fuel high pressure common injection rail2 ± 0,2
Injection pump on support2,3 ± 0,2
Union on diesel injector2 ± 0,2
Injection pump pulley5 ± 0,5
Union on fuel high pressure pump2 ± 0,2
Cooling circuit
Coolant pump1,5 ± 0,1
Coolant inlet housing1,8 ± 0,1 Engines: RHY - RHZ
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 136

Downloaded from www.Manualslib.com manuals search engine 142
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder block
13 Front closing plate screw
Flywheel screws
14Pre-tightening1,5
Tightening4,7 ± 0,4
Accessories drive pulley screw
15Pre-tightening7 ± 0,25
Angular tightening60°±5°
Engine: RHR
B1CP0GNP
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 142

Downloaded from www.Manualslib.com manuals search engine 163
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFN
Without air conditioning
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Detension the belt (3)by turning the tensioner roller (1)by means of the
screw (2)
(clockwise).
NOTE:Screw (2)has a left hand thread.
Compress the tensioner roller (1).
Remove the auxiliaries drive belt (3).
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play
and without tight spots).
Refitting.
Compress the tensioner roller (1).
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly
positioned in the grooves of the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4) : 2 ± 0,2 m.daN.
- Guide roller screw (5) : 3,5 ± 0,,3 m.daN.
- Wheel bolts: 9 ± 1 m.daN.
B1BP23PCB1BP23QCB1BP23RC
With air conditioning
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 163

Downloaded from www.Manualslib.com manuals search engine 164
ENGINE
B1BP39AC
B1BP23RC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFK
Tools.
[1]Detensioning lever for auxiliaries drive belt tensioner roller:
Dynamic spanner extension: FACOM SJ.214
Adaptor for socket 9x12 : FACOM J.274
Polygon socket 9x12 : 016
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Turn the tensioner roller(1)by the screw (2)
(anti-clockwise), using tool [1]to detension the belt (3).
NOTE: Screw (2)has a left hand thread.
Remove the auxiliaries drive belt (3).
Refitting.
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play and without tight spots).
Refitting.
Compress the tensioner roller (1), using tool [1].
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves of
the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4)tighten to: 2 ± 0,2 m.daN.
- Guide roller screw (5)tighten to: 3,5 ± 0,3 m.daN.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 164

Downloaded from www.Manualslib.com manuals search engine 252
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
- The upper timing cover (12).
- The lower timing cover (11).
- The accessories drive pulley (9).
- The screw (10).
Tightening torque
Screw (10)Pre-tighten to : 3 ± 0,3 m.daN.
Angular tighten : 180° ± 5°.
Remove tool [1].
Refit:
- The engine support (8), tighten to 5,5 ± 0,4 m.daN.
- The engine support (4), tighten to 6,1 ± 0,6 m.daN.
- The engine support (5), tighten to 2,5 ± 0,2 m.daN.
- The electrical harness (7).
- The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
- The tube (2).
- The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
- The fuel unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
- The accessories drive belt
(see corresponding operation).
- The front RH splash-shield (see corresponding operation).
- The front RH wheel, tighten to 9 ± 1 m.daN.
- Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following
a reconnection of the battery
(see corresponding operation).
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 252