2005 Citroen XSARA PICASSO check engine

Downloaded from www.Manualslib.com manuals search engine 15
GENERAL
Engine type
Engine with filter element filtrante
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After draining
Hydraulic or brake circuit
Cooling circuit
Fuel tank capacity
NFV 6FZ RFN 9HZ 9HY RHY
3 4,25 3,75 4,5
1,5 1,7 1,55 (3) 1,4
1,81,8
6
3
0,58 litres
5,8 (1) and (2) 6,5 (1) and (2) 11 11 (1) and (2)
55 60
XSARA PICASSO CAPACITIES (in litres)
Diesel Petrol
1.6i1.8i 16 V 2.0i 16V 1.6 16V HDi
(1) = With air conditioning.
(2) = Without air conditioning.
(3) = RPO 9884 ➔ = Restyled XSARA PICASSO.
ESSENTIAL: Systematically check the oil level using the oil dipstick.
AUTO.
2.0 HDi
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 15

Downloaded from www.Manualslib.com manuals search engine 16
GENERALEngine type
Engine with filter element
Between Min. and Max.
5-speed gearbox
Hydraulic or brake circuit
Cooling circuit
Fuel tank capacity
HFX KFW NFU 9HX WJY RHY
3 3,25 3,75 4,5
1,5 1,55 1,2 1,4
2 1,8
With ABS = 0,45 - Without ABS = 0,36
89
55 60
BERLINGO CAPACITIES (in litres)
Diesel Petrol
1.1i 1.4i1.6i 16V
2.0 HDi
1.9 D
(1)
(1) = Manual dipstick without twists but with a sphere.
ESSENTIAL: Systematically check the oil level using the oil dipstick.
1.4i 16V HDi
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 16

Downloaded from www.Manualslib.com manuals search engine 47
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder head
1 Inlet air pressure sensor 0,8 ± 0,12 Motorised butterfly housing fixing screws 0,8 ± 0,23 Coolant outlet housing screw 0,8 ± 0,24 Oxygen sensor 4,7 ± 0,7
Catalytic converter fixing nuts (*)
5Pre-tightening2 ± 0,2
Tightening4 ± 0,4
Check the tightening4 ± 0,46 Exhaust manifold nuts 1,8 ± 0,27 Exhaust manifold fixing stud 0,8 ± 0,1
Cylinder head bolts (*)
8Pre-tightening1,5 ± 0,2
Tightening2,5 ± 0,2
Angular tightening200° ± 5°9 Inlet manifold screws 0,8 ± 0,110 Valve cover screws (*) 0,9 ± 0,111 Camshaft bearing cap screws (*) 1 ± 0,112 Sparking plugs 2,25 ± 0,2
13Camshaft dephaser electrovalve fixing screws
0,8 ± 0,2
(VVT)
Engine: KFU
B1BP368P
(*) = IMPERATIVE: Respect the tightening sequence (see following page).
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 47

Downloaded from www.Manualslib.com manuals search engine 55
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder head1 Inlet air pressure sensor 0,8 ± 0,12 Motorised butterfly housing fixing screws 0,7 ± 0,13 Inlet manifold nuts 0,8 ± 0,24 Valve cover screws (*) 0,9 ± 0,15 Coolant outlet housing screw 0,8 ± 0,26 Thermostat fixing screw 0,8 ± 0,27 Oxygen sensor 4,7 ± 0,7
Catalytic converter fixing nuts (*)
8Pre-tightening1,8 ± 0,3
Tightening4 ± 0,4
Check the tightening4 ± 0,49 Exhaust manifold nuts 2,3 ± 0,510 Exhaust manifold fixing stud 0,8 ± 0,111 Lubrication plug 1,5 ± 0,2
Cylinder head bolts (*)
12Tightening2 ± 0,2
Angular tightening260° ± 5°13 Camshaft bearing cap screws (*) 0,9 ± 0,114 Inlet manifold fixing stud 0,8 ± 0,115 Engine coolant temperature sensor (CMM) 1,7 ± 0,116 Engine coolant temperature sensor (instrument panel) 1,7 ± 0,1
17 Sparking plugs 3 ± 0,1
Engine: NFU
B1BP362P
(*) = IMPERATIVE: Respect the tightening sequence (see following page).
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 55

Downloaded from www.Manualslib.com manuals search engine 154
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: All Types Petrol and Diesel
Tools.
- Belt tension measuring instrument: 4122 - T (C.TRONIC 105.5).
WARNING: If using tool 4099-T (C.TRONIC 105).
Essential.
- Before refitting the auxiliary equipment drive belt, check that:
- 1 / The roller(s) rotate freely (no play or stiffness).
- 2 / The belt is correctly engaged in the grooves of the various pulleys.
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 154

Downloaded from www.Manualslib.com manuals search engine 157
ENGINE
B1EP1GQD
AUXILIARY EQUIPMENT DRIVE BELT
Engine: KFU
Véhicule with air conditioning.
Removing.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Place tool [3]at «b».
Remove the auxiliary equipment drive belt.
IMPERATIVE: Check that the dynamic tensioner roller turns freely
(without play and without tight
spots).
Refitting.
NOTE: Visually check the condition of the auxiliary equipment drive belt prior to refitting.
Place tool [4]at «a».
Compress the dynamic tensioner roller.
Remove tool [3].
Refit the auxiliary equipment drive belt.
Respect the following sequence:
- Crankshaft pinion, aircon compressor pulley, alternator pulley, dynamic tensioner roller.
Remove the tools.
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 157

Downloaded from www.Manualslib.com manuals search engine 158
ENGINE
B1BP234C
XSARA PICASSOAUXILIARY EQUIPMENT DRIVE BELT
Engine: NFV
Without air conditioning
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument: 4122 -T
[3] TORX spanner
Remove.
Release the central screw (1), tool[3].
Detension the tensioner roller (2)
(flat spanner 27on flat).
Remove the belt.
Refit.
Position the belt.
Hold the belt in position using the tensioner roller (2).
Pre-tension the belt 120 SEEMunits, tool [2].
Lock the central screw (1)tool [3].
Remove the tool [2].
Rotate the crankshaft 2to 4 times.
Check the tension, 120 SEEMunits.
If not, restart the operation.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 158

Downloaded from www.Manualslib.com manuals search engine 161
ENGINE
B1EP1FUD
B1EP1FVC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFJ
Tool.
[1]«Junior» T extension: (-).1608.E
Removing.
Engage tool [1]in the notch «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Remove the auxiliaries drive belt.
Carefully release the tensioner roller (1)to reach its minimum.
Remove tool[1].
IMPERATIVE: Check that the roller (1) turns freely
(without play and without tight spots).
Refitting.
If removing the auxiliaries drive belt tensioner roller, tighten the screws 2 ± 0,2 m.daN.
Engage tool [1]in the notch at «a».
Exert on the roller (1)an effort upwards to hold it at maximum.
Position the
(new)auxiliaries drive belt, in the following sequence:
- Auxiliaries drive pulley (4), aircon compressor pulley (3), tensioner roller (1)and alternator pulley (2).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves of
the various pulleys.
Release the tensioner roller (1).
Remove tool [1].
Checking the tension of the auxiliaries drive belt.
Check the tension of the auxiliaries drive belt:
- Mark «b»at the level of mark «c», new belt.
- Mark «b»at the level of mark «d», belt to be changed.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 161