2005 Citroen C4 ring

Downloaded from www.Manualslib.com manuals search engine 175
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning (continued)
Refitting.
Refit the belt.
Using a 7 mmsquare drive at "b", turn the roller (3), until the tool [1] located at "a"becomes
free.
Tighten the screw (2).
Remove the tool [1].
B1BP1SLC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 175

Downloaded from www.Manualslib.com manuals search engine 178
ENGINEXSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning
B1BP1YLD
Tools.
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removal.
Re-use of belt.
WARNING: Mark the direction the belt was fitted in case of re-use of the same belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Hold the tensioner roller (7) compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Peg using tool [2], at «d».
Loosen the screw (6).
Bring the eccentric roller (5)towards the rear.
Tighten the screw (6)by hand.
Remove the belt.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 178

Downloaded from www.Manualslib.com manuals search engine 185
ENGINE
Tools.
[1]Flywheel peg: 4507-T.A
[2] Camshaft pulley peg: 4507-T.B Toolkit 4507-T
[3]Square: 4507-T.J
[4] Belt tension measuring instrument: 4122-T
[5] Valve rocker thrust plate: 4533-T.Z
Checking the timing.
Peg the flywheel, using tool [1].
Peg the camshaft pulley, using tool [2].
Setting the timing.
NOTE:Remove the sparking plugs, to ease rotation of the crankshaft.
Rotate the engine by means of the crankshaft screw (1).
Peg the camshaft pinion.
Peg the flywheel
Slacken the nut (2).
Fullt detension the belt by acting on the tensioner roller.
Remove the belt.
IMPERATIVE: Check that the tensioner roller turns freely
(no tight spot).
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
B1EP067CB1EP066CB1EP068C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 185

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Overtension on the belt.
Position «a»: Tensioner roller in detensionedposition.
Position «b»: Tensioner roller in normalposition.
Position «c»: Tensioner roller in overtensionposition.
Turn the tensioner roller (10), using an allen spanner at «e».
Place the index «d»in position «c», hold the belt to the maximum of the interval indicated.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
Rotate the crankshaft four turns
(normal direction of rotation).
IMPERATIVE: Never turn it backwards.
Check the timing setting by refitting the pegs [1], [2] and [3].
Remove the pegs [1], [2]and [3].
Adjusting the fitting tension of the timing belt.
Slacken the nut, holding the position of the tensioner roller, using an allen spanner at «e».
Bring the index «d»to its adjustment position at «b».
WARNING: The index «d» should not go past the notch «b». If it does, repeat the operation
to tension the timing belt.
Maintain the roller (10)in this position, using an allen spanner.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing. If it
does, repeat the operation to tension the timing belt.
Complete the refitting.
B1EP1DTC
B1EP1DUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 192

Downloaded from www.Manualslib.com manuals search engine 193
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Belt tension measuring instrument: 4122-T
[2]Flywheel locating peg: 4507-T.A
[3]Camshaft pulley locating peg, exhaust: 4533-T.A C2 Tool kit 4507-T
[4]Camshaft pulley locating peg, inlet: 4533-T.A C1
[5]Tensioning tool: 4707-T.J
Checking the valve timing.
Peg the flywheel using the tool [2].
Peg the exhaust camshaft pulley [3].
Peg the inlet camshaft pulley [4].
Setting the valve timing.
Peg the flywheel using the tool [2].
Peg the camshaft pulleys[3]and [4].
B1EP11CC
B1EP11BC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 193

Downloaded from www.Manualslib.com manuals search engine 195
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Turn the two pulleys (1)clockwise to the end of the slots.
With the belt strip (e)fully tensioned, place the belt over the pulley, first exhaust side, then inlet side, while
ensuring that marks (b)and (c)on the belt are aligned with marks (f)on the pulleys.
Hold the belt in this position and engage it over the water pump pinion and the tensioner roller.
Fit the tool [1] on the belt at (e).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction, to obtain: 63 SEEMunits.
Tighten the roller (2)to 2 m.daN.
Tighten the six screws (5)to 1 m.daN.
Essential: Check that:
- The camshaft pulleys (1)are not at the end of the slots
(by removing a screw).
- The markings on the belt are aligned with the markings on the crankshaft and camshaft pulleys.
If not, repeat the setting procedure.
B1EP11GC
B1EP11FC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 195

Downloaded from www.Manualslib.com manuals search engine 196
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Remove the tools [1], [2], [3]and [4].
Rotate the engine by four turnsin the normal direction
(do not turn backwards).
Peg the flywheel [2].
Loosen the six screws (5), while ensuring there is still a slight amount of friction with the pulley.
Peg the camshaft hubs using pegs [3]and [4].
WARNING: In certain cases, it may be necessary to slightly turn the camshaft using the hub fixing screw.
Fit the tool [1].
Loosen the tensioner roller screw (2).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction to obtain: 37 SEEMunits.
Tighten the tensioner roller screw (2)to 2 m.daN.
Tighten the six pulley screws (1)to 1 m.daN.
Remove the tools.
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 196