2005 Citroen C4 engine

Downloaded from www.Manualslib.com manuals search engine 403
BRAKES
TIGHTENING TORQUES: BRAKING SYSTEM
B3FP7DZC
B3FP7EOC
Rear brakes
10Unions on brake piping1,5 ± 0,1
11Rear brake caliper support 5,3 ± 0,5
12Rear brake caliper3 ± 0,3
13Wheel sensor0,8 ± 0,1
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 403

Downloaded from www.Manualslib.com manuals search engine 404
BRAKES
B3FP7E2D
ABS/ESP HYDRAULIC BLOCK
Components Supplier Type Observations
Hydraulic blockBOSCHABS REF 8.0
Installed under the front LH
ESP 8.0chassis member. 4 regulation channels.
The emergency braking control is incorporated in the primary piston at «a».
B3FP7E3C
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 404

Downloaded from www.Manualslib.com manuals search engine 405
BRAKES
PARKING BRAKE ADJUSTMENT
Adjustment.
IMPERATIVE: Respect the safety and cleanliness requirements.
Raise and support the vehicle.
Remove the central console.
WARNING: Check the routing of the brake cables under the vehicle.
Release the handbrake lever.
Press gently on the brake pedal
(then repeat the operation 3 times).
Action the handbrake lever with a force of 40 daN.
Use a feeler gauge at «J»to measure the movement of the lever in relation to its stop.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
(1)Nut for adjusting the tension of the handbrake cables
Move the nut (1)to obtain a movement «J»less than or equal to 1,5 mm.
Action the handbrake lever 8 timeswith a force of 40 daN.
With the handbrake released, check the movement «j»with a feeler gauge.
NOTE:The movement should be less than 1,5 mmand more than 0,05 mm.
Refit the central console
(see corresponding operation).
Check the efficiency of the handbrake.
B3FP7F1C
B3FP7F2D
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 405

Downloaded from www.Manualslib.com manuals search engine 406
BRAKES
B3FP7EQC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1]Bleeding apparatus: «LURO» or similar
[2]LEXIA diagnostic tool: 4171-T
[3]PROXIA diagnostic tool: 4165-T
NOTE:Bleeding of the secondary braking circuit is done with the aid of diagnostic tools [2]and [3].
Draining of the brake fluid reservoir.
Remove the screws (3)and the battery tray (2).
Remove the filter of the brake fluid reservoir (4).
Drain the brake fluid reservoir (4)to the maximum extent
(if necessary, use a clean syringe).
Remove the screws (1).
Uncouple the clickfit union at «a».
Remove the brake fluid reservoir (4).
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 406

Downloaded from www.Manualslib.com manuals search engine 407
BRAKES
B3FP7ESD
BLEEDING AND FILLING THE BRAKING SYSTEM
Disconnect the connector «b».
Uncouple the pipe (5).
Remove the reservoir (6), moving aside the tabs «c»of the pins (7).
Clean the brake fluid reservoir (4) and the brake fluid reservoir (6).
Refit the brake fluid reservoir (6).
Couple the pipe (5).
Reconnect the connector «b».
Couple the clickfit union, at «a».
Refit:
- The brake fluid reservoir (4).
- The screws (1).
- The filter of the brake fluid reservoir.
- The battery tray.
- The screws (3).
- The battery.
Reconnect the battery.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B3FP7ERC
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 407

Downloaded from www.Manualslib.com manuals search engine 408
BRAKES
B3FP7EUC
BLEEDING AND FILLING THE BRAKING SYSTEM
Filling the braking circuit.
WARNING: Use only the approved and recommended hydraulic fluids.
IMPERATIVE: Only use new brake fluid that has not emulsified; avoid any introduction of
impurities into the hydraulic circuit.
Fill the brake fluid reservoir (4).
Bleeding the primary braking circuit.
WARNING: During the bleed operations: take care to maintain the level of the brake fluid
in the reservoir, keep it topped up.
WARNING: The ABS system must not be in action during the bleed operation.
WARNING: Respect the sequence for the opening of the bleed screws.
Front brake caliper : Bleed screw (8).
Rear brake caliper : Bleed screw (9).
Bleed each brake caliper, proceeding in the following sequence:
- Front LH wheel.
- Front RH wheel.
- Rear LH wheel.
- Rear RH wheel.
B3FP7ETC
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 408

Downloaded from www.Manualslib.com manuals search engine 409
BRAKES
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding the braking circuit with the bleed apparatus.
Connect the bleed apparatus [1]on the brake fluid reservoir (4).
Adjust the apparatus pressure to 2 bars.
For each brake circuit:
- Couple a transparent tube on the bleed screw.
- Submerge the other end of the tube in a clean container.
- Open the bleed screw.
- Wait until the brake fluid flows out without air bubbles.
- Close the bleed screw.
- Remove the bleed apparatus [1].
Check the level of the brake fluid
(between the «DANGER»level and the «MAXI»level).
Fill if necessary with the the approved and recommended synthetic brake fluid.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 409

Downloaded from www.Manualslib.com manuals search engine 410
BRAKESBLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding the braking circuit without the bleed apparatus.
NOTE:Two operators are necessary.
For each brake circuit:
- Apply the brake pedal to place the circuit under pressure.
- Couple a transparent tube on the bleed screw.
- Submerge the other end of the tube in a clean container.
- Open the bleed screw.
- Wait until the fluid flows out without air bubbles.
- Close the bleed screw.
NOTE:Recommence the process a second timeif that is necessary.
Check the level of the brake fluid
(between the «DANGER»level and
the «MAXI»level).
Fill if necessary with the the approved and recommended synthetic
brake fluid.Bleeding the secondary braking circuit.
WARNING: During the bleed operations: take care to maintain the
level of the brake fluid in the reservoir, keep it topped up.
NOTE:The bleed apparatus [1]is still connected on the brake fluid
reservoir (4).
Use the diagnostic tools [2]or [3].
Select the menu corresponding to the vehicle:
- ABSmenu
(according to equipment).- ESPmenu (according to equipment).
Follow the instructions of the diagnostic tool.
At the end of the bleed programme, check the level of the brake fluid,
top up if necessary.
Check the travel of the brake pedal: it must not be excessive. If it is,
restart the bleed procedure.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 410