2005 Citroen C4 air

Downloaded from www.Manualslib.com manuals search engine 162
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: 6FZ - RFN
Without air conditioningWith air conditioning
Tool.
[1] Pliers for removing plastic pegs: 7504-T
Remove the belt.
Detension the belt (3)by turning the screw (2)of the tensioner roller (1)
(anti-clockwise).
The screw (2)
(WARNING: not left hand screw).
Remove the belt (3), while keeping the tensioner roller (1)tight.
Refit the belt.
Refit the belt (3), while keeping the tensioner roller (1)tight.
Release the tensioner roller (1).
B1BP23PCB1BP23QCB1BP23PCB1BP23RC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 162

Downloaded from www.Manualslib.com manuals search engine 163
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFN
Without air conditioning
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Detension the belt (3)by turning the tensioner roller (1)by means of the
screw (2)
(clockwise).
NOTE:Screw (2)has a left hand thread.
Compress the tensioner roller (1).
Remove the auxiliaries drive belt (3).
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play
and without tight spots).
Refitting.
Compress the tensioner roller (1).
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly
positioned in the grooves of the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4) : 2 ± 0,2 m.daN.
- Guide roller screw (5) : 3,5 ± 0,,3 m.daN.
- Wheel bolts: 9 ± 1 m.daN.
B1BP23PCB1BP23QCB1BP23RC
With air conditioning
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 163

Downloaded from www.Manualslib.com manuals search engine 169
ENGINE
B1BP2Z6D
B1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ - 9HY
Tools.
[1]Dynamic tensioner compression lever: (-).0188.Z
[2]Peg for dynamic tensioner roller: (-).0194.F
Removing.
Remove the front RH wheel, the under-engine sounddeadening and the splash-shield.
V
ehicle with air conditioning.
WARNING: Mark the direction of fitting of the accessories drive belt, if it is to be re-used.
Compress the tensioner roller(1)by acting at «a»
(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without tight
spots).
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 169

Downloaded from www.Manualslib.com manuals search engine 171
ENGINE
XSARAAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering, with air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (1).
Tighten the screw (2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] at "e".
Tighten the screw (2)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (1)to 2 m.daN.
Remove the tool [1].
B1BP1SGCB1BP1SFC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 171

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172

Downloaded from www.Manualslib.com manuals search engine 173
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Power-assisted steering, without air conditioning (continued)
XSARA
Refitting.
Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1] with the knob downwards.
Tighten the nut (2)to obtain a value of:
Reused belt:
- Keep the value taken at removal.
New belt:
- Tension should be 110 SEEMunits.
- Tighten the screw (1)to 9.5 m.daN.
- Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEMunits.
- Remove the tool [1].
- Start the engine and run it for 10 seconds.
- Stop the engine.
- Place the tool [1]on the belt at "f".
- Tension should be 130 ± 4 SEEMunits.
- Remove the tool [1].
B1BP1SJD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 173

Downloaded from www.Manualslib.com manuals search engine 174
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning
Tools.
[1] Dynamic tensioner peg: (-) 0188 H
[2] Belt tension measuring instrument: 4122-T
Removal.
Peg the dynamic tensioner (1) at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
- Loosen the screw (2)of the roller (3).
- Using a 7 mmsquare drive, turn the roller (3)at "b".
- Peg the tensioner (1) at "a", using tool [1].
NOTE: If the belt is broken:
- Support the engine using a jack
(insert a wooden block between the housing and the jack).
- Remove the right engine support.
- Using a square drive at (b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 174

Downloaded from www.Manualslib.com manuals search engine 175
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning (continued)
Refitting.
Refit the belt.
Using a 7 mmsquare drive at "b", turn the roller (3), until the tool [1] located at "a"becomes
free.
Tighten the screw (2).
Remove the tool [1].
B1BP1SLC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 175