2005 Citroen C4 Auxiliary belt

Downloaded from www.Manualslib.com manuals search engine 175
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning (continued)
Refitting.
Refit the belt.
Using a 7 mmsquare drive at "b", turn the roller (3), until the tool [1] located at "a"becomes
free.
Tighten the screw (2).
Remove the tool [1].
B1BP1SLC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 175

Downloaded from www.Manualslib.com manuals search engine 176
ENGINEXSARA - XSARA PICASSO AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
Without air conditioning
B1BP1YKD
Tools.
[1] Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removing.
Re-use of belt.
WARNING: Mark the direction the belt was fiited in case of re-use of the same belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Keep the tensioner roller (2)compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Peg using tool [2]at «b».
Keep the tensioner roller (2)compressed and remove the belt.
Loosen the screw (1).
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 176

Downloaded from www.Manualslib.com manuals search engine 177
ENGINE
XSARA - XSARA PICASSO AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
Without air conditioning (continued)
Refitting.
Re-used belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Refit the belt.
WARNING: Respect the belt-fitting direction.
Remove the tool [4].
New belt.
Refit the belt.
Turn the eccentric roller (3), tool [1]
(clockwise)to free the tool [2]from
its pegging at «b».
Hold the eccentric roller (3), tool [1]and tighten the screw (1)to 4.3 m.daN.
Remove the tool [2].
Rotate the crankshaft 4 timesin the direction of rotation.
Check that it is possible to peg at «b», tool [3].
If not possible to peg, restart the adjustment.
B1BP1YMD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 177

Downloaded from www.Manualslib.com manuals search engine 178
ENGINEXSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning
B1BP1YLD
Tools.
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removal.
Re-use of belt.
WARNING: Mark the direction the belt was fitted in case of re-use of the same belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Hold the tensioner roller (7) compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Peg using tool [2], at «d».
Loosen the screw (6).
Bring the eccentric roller (5)towards the rear.
Tighten the screw (6)by hand.
Remove the belt.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 178

Downloaded from www.Manualslib.com manuals search engine 179
ENGINE
XSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning (continued)
Refitting.
Re-used belt.
Compress the tensioner roller (7)by action at «c»
(in anti-clockwise direction), tool [4].
Refit the belt.
WARNING: Respect the direction belt was fitted.
Remove the tool [4].
New belt.
Refit the belt.
Turn the eccentric roller (5), tool[1]
(clockwise)to free the tool [2]from its pegging
at «d».
Hold the eccentric roller (5), tool [1]and tighten the screw (6)to 4.3 m.daN.
Remove the tool [2].
Rotate the crankshaft 4 timesin the direction of rotation.
Check that it is possible to peg at «d», tool [3].
If not possible to peg, restart the adjustment.
B1BP1YND
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 179

Downloaded from www.Manualslib.com manuals search engine 180
ENGINE
B1BP2J5D
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHV - 4HY
Tools.
[1]Dynamic tensioner compression lever: (-).0188.Z.
[2]Dynamic tensioner roller retaining peg Ø 4 mm : (-).0188.Q1
Removing.
Remove the splash-shield, under-engine sound-deadening, front RH wheel.
WARNING: Mark the direction of fitting of the auxiliaries drive belt in the case of
re-use of the belt.
Compress the dynamic tensioner roller (1)by acting at «b»
(anti-clockwise), using tool [1].
Peg using tool [2]at «a».
IMPERATIVE : Check that the roller (1) turns freely
(without play and without tight
spots).
Refitting.
Refit the auxiliaries drive belt.
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in
the grooves of the various pulleys.
Compress the dynamic tensioner roller (1)by acting at «b», using tool [1].
Remove tool [2] at «a».
Complete the refitting.
JUMPER
Without air conditioning
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 180

Downloaded from www.Manualslib.com manuals search engine 232
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1BP2LXC
Tools.
[1] Pliers for removing plastic pegs: 7504-T
[2]Lever for detensioning the dynamic tensioner roller: (-).0194.E
[3]Engine flywheel setting peg: (-).0194.C
[4] Camshaft setting peg: (-).0194.B
[5]Crankshaft and high pressure pump setting peg: (-).0194.A
Preliminary operations.
Remove:
- The front RH wheel.
- The front RH splash-shield, using tool [1].
- The clips of the electrical harness on the upper timing cover.
- The accessories belt, using tool [2]
(see corresponding operation).
Checking the setting.
Disconnect the battery negative cable.
Remove the upper timing cover (1).
Rotate the engine using the screw (2)of the crankshaft pulley.
NOTE:The locking hole is located under the crankshaft bearing cap cover.
Undo the screw (2).
Detension the auxiliary drive belt dynamic tensioner roller, using tool [2].
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 232