2005 Citroen C4 ash

Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING THE VALVE TIMING
Engine: RFN
Tools.
[1]Camshaft setting peg: (-).0189.A
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking the timing.
Removing.
Disconnect the battery negative terminal.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel, the splash-shield and the upper timing cover.
A:Pegging on the manualgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging
position.
Peg the crankshaft, using tool [2].
Unclip the fuel supply hose from the timing cover.
B1BP36QD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 210

Downloaded from www.Manualslib.com manuals search engine 217
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Tools.
[1]Camshaft setting peg: (-) 0189.A
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-).0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Tool for moving and locking the tensioner roller: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189 S2
Pliers for removing plastic pins: 7504-T
Checking the setting of the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The upper timing cover.
C4AP12TC
XSARA - XSARA PICASSO
Engines: 6FZ - RFN
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 217

Downloaded from www.Manualslib.com manuals search engine 219
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The accessories drive belt
(see corresponding operation).
Unclip and move aside the fuel delivery hose from the timing cover.
Remove the upper timing cover (1).
Turn the engine by means of the screw (3)of the crankshaft pulley (2)to bring it to the pegging position.
B1BP2V4C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 219

Downloaded from www.Manualslib.com manuals search engine 224
ENGINECHECKING THE VALVE TIMING
Engine: RFK
Tools.
[1]Camshaft setting peg: (-).0194.B
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking the timing.
Removing.
Disconnect the battery negative terminal.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel and the splash-shield.
A:Pegging on the manualgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
Peg the crankshaft, using tool [2].
Unclip:
- The fuel supply hose from the upper timing cover.
- The fuel vapour re-induction circuit.
B1BP2V5D
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 224

Downloaded from www.Manualslib.com manuals search engine 232
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1BP2LXC
Tools.
[1] Pliers for removing plastic pegs: 7504-T
[2]Lever for detensioning the dynamic tensioner roller: (-).0194.E
[3]Engine flywheel setting peg: (-).0194.C
[4] Camshaft setting peg: (-).0194.B
[5]Crankshaft and high pressure pump setting peg: (-).0194.A
Preliminary operations.
Remove:
- The front RH wheel.
- The front RH splash-shield, using tool [1].
- The clips of the electrical harness on the upper timing cover.
- The accessories belt, using tool [2]
(see corresponding operation).
Checking the setting.
Disconnect the battery negative cable.
Remove the upper timing cover (1).
Rotate the engine using the screw (2)of the crankshaft pulley.
NOTE:The locking hole is located under the crankshaft bearing cap cover.
Undo the screw (2).
Detension the auxiliary drive belt dynamic tensioner roller, using tool [2].
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 232

Downloaded from www.Manualslib.com manuals search engine 239
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1EP18LCB1BP2LZC
Setting the timing (continued).
Refit:
- The intermediate RH engine support, tighten the screws (16)to 5,5 ± 0,5 m.daN.
- The RH engine support, tighten the screws (17)to 4,5 ± 0,4 m.daN.
- The bottom timing cover (3).
Immobilise the engine flywheel, using tool [3].
Remove the screw (2).
Refit the accessories drive pulley and tighten to:
- Pre-tighten to : 3 ± 0,3 m.daN.
- Angular tighten to: 180° ± 1,8°.
Remove tool [3].
Refit:
- The top cover (1).
- The accessories belt
(see corresponding operation).
- The exhaust line
(see corresponding operation).
- The front RH splash-shield.
- The front RH wheel.
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 239

Downloaded from www.Manualslib.com manuals search engine 249
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
B1BP304D
Tools.
[1] Flywheel setting peg: (-).0194.C
[2]Camshaft setting peg: (-).0194.B
[3]Crankshaft setting peg: (-).0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove:
- The front RH wheel.
- The front RH splash-shield.
- The accessories drive belt
(see corresponding operation).
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line
(at the flexible pipe).
Disconnect the connecter at «a».
Remove and move aside the power steering fluid reservoir (6).
Uncouple, plug and move aside the tube (2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports (4)and (5).
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 249

Downloaded from www.Manualslib.com manuals search engine 252
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
- The upper timing cover (12).
- The lower timing cover (11).
- The accessories drive pulley (9).
- The screw (10).
Tightening torque
Screw (10)Pre-tighten to : 3 ± 0,3 m.daN.
Angular tighten : 180° ± 5°.
Remove tool [1].
Refit:
- The engine support (8), tighten to 5,5 ± 0,4 m.daN.
- The engine support (4), tighten to 6,1 ± 0,6 m.daN.
- The engine support (5), tighten to 2,5 ± 0,2 m.daN.
- The electrical harness (7).
- The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
- The tube (2).
- The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
- The fuel unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
- The accessories drive belt
(see corresponding operation).
- The front RH splash-shield (see corresponding operation).
- The front RH wheel, tighten to 9 ± 1 m.daN.
- Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following
a reconnection of the battery
(see corresponding operation).
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 252