2005 Citroen C4 Pump

Downloaded from www.Manualslib.com manuals search engine 371
AXLES
SUSPENSION
STEERING
C4CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Tools.
[1]Pressure gauge: (-).0710.AZ
[2]Checking tube: pressure gauge to tap: (-).0710.B1
[3]Checking tube: high pressure pipe to tap: (-).0710.B2
[4]Checking tube: high pressure pump to tap: (-).0710.B3
[5]3-way tap: (-).0710.C
[6]Union: (-).0710.J
[7]Union: (-).0710.K
[8] Plugs for checking valve sealing: (-).0710.H
Precautions to be taken.
Work with care to avoid entry of polluting particles into the circuit.
NOTE:The correct operation of the system requires perfect cleanliness of the fluid and of the
hydraulic components.
Check:
- The level of the power steering fluid.
- The condition of the piping and unions.
Using the tools.
Prepare the checking assembly [1], [2], [3], [4], [5], [6]and [7].
Attach the tool [1].
Remove the front RH wheel, the splash-shield and the screen wash reservoir.
B3EP16CC
B3EP16DC
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 371

Downloaded from www.Manualslib.com manuals search engine 372
AXLES
SUSPENSION
STEERING
CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Preliminary operation.
Move aside the high pressure pipe (1).
Do up:
- The union [6]on the power steering electropump.
- The union [7]on the high pressure pipe (1).
- Tighten all the unions.
Fill the power steering reservoir 10 mmabove the max. level.
IMPERATIVE: Use new power steering fluid for both filling and topping-up the circuit.
Open the tap [5].
Start the engine and allow it to run for 5 seconds.
Stop the engine.
Move the steering several timesin each direction.
Check the steering fluid level and make sure that there are no leaks.
Checking the electropump pressure.
Start the engine.
Close the tap [5]for 5 seconds.
Open the tap [5].
Stop the engine.
At accelerated idle
(1200 to 1500rpm), the pressure should be 105 ± 5 bars.
If the electropump pressure is correct, check the valve sealing.
B3EP16EC
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 372

Downloaded from www.Manualslib.com manuals search engine 373
AXLES
SUSPENSION
STEERING
CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Checking the valve sealing.
Remove the under-engine shield.
Move aside the heat shield from the steering mechanism.
Slacken the unions (2)on the power steering ram.
Uncouple the two supply pipes (3)from the distributor valve and move them aside.
Fit on the distributor valve the two plugs [8], tighten to 0,8 m.daN.
Move the steering slowly from lock to lock, to drain the ram.
Top up the level of the power steering fluid.
Open the tap [5].
Stop the engine.
Maintain the engine speed at accelerated idle.
Hold the wheels on full lock, first on one side then on the other.
The pressure should adjust to 105 ± 5 bars.
The pressure is correct: replace the steering mechanism.
The pressure is lower than the values above: replace the distributor valve.
Couple the two supply pipes (3)on the distributor valve; tighten to 0,8 m.daN.
Retighten the unions (2)on the power steering ram; tighten to 0,8 m.daN.
Remove the union [7]on the high pressure pipe (1)and the union [6]on the power steering
electropump.
Refit:
- the high pressure pipe (1); tighten to 2 ± 0,2 m.daN.
- the screen wash reservoir, the front RH splash-shield and the front RH wheel.
B3EP16FC
B3EP16GC
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 373

Downloaded from www.Manualslib.com manuals search engine 387
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
XSARA
Power-assisted steering assembly
T
ightening torques (m.daN).
High pressure tube (rubber seal pump side)Power-assisted valve and pump union: 2.5
Return pipe.
Power-assisted valve union: 2.5
(16)Upper front fixing (E3) : 2.5
(17)Upper rear fixing (E3) : 2.2
(18)Fixing (E3) : 2.2
Tightening sequence.
Tighten screws (16) and (18).
Lightly tighten screw (17), then fully tighten.
Pressure switch on the pressure circuit.
Switch opens 30to 35 bars.
Switch closes 25 bars.
Tighten to: 2 m.daN.
B3EP045D
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 387

Downloaded from www.Manualslib.com manuals search engine 397
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
Unions between pump unions and power steering valve: 2 ± 0.3
(16)Fixing screw: 2.2 ± 0.3
(17)Fixing screw: 2.2 ± 0.3
(18) Fixing screw: 2.2 ± 0.3
NOTE: Coat the threads with product «E3».
A pressure switch is implanted in the hydraulic piping between the high
pressure pump and the power steering valve.
- Opening pressure = 30 / 35 bars.
- Closing pressure = 25 barsminimum.
Tightening torque = 2 ± 0.2.
B3EP118D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 397