2005 Citroen BERLINGO air flow

Downloaded from www.Manualslib.com manuals search engine 102
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder head
9 Exhaust manifold 2,5 ± 0,2
10 Exhaust manifold stud 1 ± 0,2
11 Turbocompressor nuts 2,6 ± 0,6
12 Catalytic converter nuts 2 ± 0,1
Air flowmeter
13Pre-tightening0,1
Tightening0,9 ± 0,2
Engine: 9HX
B1BP39YP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 102

Downloaded from www.Manualslib.com manuals search engine 409
BRAKES
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding the braking circuit with the bleed apparatus.
Connect the bleed apparatus [1]on the brake fluid reservoir (4).
Adjust the apparatus pressure to 2 bars.
For each brake circuit:
- Couple a transparent tube on the bleed screw.
- Submerge the other end of the tube in a clean container.
- Open the bleed screw.
- Wait until the brake fluid flows out without air bubbles.
- Close the bleed screw.
- Remove the bleed apparatus [1].
Check the level of the brake fluid
(between the «DANGER»level and the «MAXI»level).
Fill if necessary with the the approved and recommended synthetic brake fluid.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 409

Downloaded from www.Manualslib.com manuals search engine 410
BRAKESBLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding the braking circuit without the bleed apparatus.
NOTE:Two operators are necessary.
For each brake circuit:
- Apply the brake pedal to place the circuit under pressure.
- Couple a transparent tube on the bleed screw.
- Submerge the other end of the tube in a clean container.
- Open the bleed screw.
- Wait until the fluid flows out without air bubbles.
- Close the bleed screw.
NOTE:Recommence the process a second timeif that is necessary.
Check the level of the brake fluid
(between the «DANGER»level and
the «MAXI»level).
Fill if necessary with the the approved and recommended synthetic
brake fluid.Bleeding the secondary braking circuit.
WARNING: During the bleed operations: take care to maintain the
level of the brake fluid in the reservoir, keep it topped up.
NOTE:The bleed apparatus [1]is still connected on the brake fluid
reservoir (4).
Use the diagnostic tools [2]or [3].
Select the menu corresponding to the vehicle:
- ABSmenu
(according to equipment).- ESPmenu (according to equipment).
Follow the instructions of the diagnostic tool.
At the end of the bleed programme, check the level of the brake fluid,
top up if necessary.
Check the travel of the brake pedal: it must not be excessive. If it is,
restart the bleed procedure.
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 410

Downloaded from www.Manualslib.com manuals search engine 439
Checking.
Position the toolCLIM TEST II
(according to the manufacturer's instructions).
Preliminary operations.
Close all the front air vents.
Start the engine.
Open the front LH air vent.
Position the air distribution control to«frontal flow».
Activate the«air recirculation» control.
Activate the«air conditioning» control.
Positions of the air conditioning controls:
- Temperature control on maximum cold.
- Blower control in maximum speed position.
Let the air conditioning operate for5 minutes.
CHECKING THE EFFICIENCY OF THE AIR CONDITIONING SYSTEM
E5AP2FAC
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 439