2005 CHRYSLER VOYAGER manual transmission

(2) Install transaxle oil filter (Fig. 374). Inspect
the o-ring and replace if necessary.
(3) Ensure the transaxle oil pan and transaxle
case sealing surfaces are clean and dry. Install an
1/8º bead of MopartSilicone Rubber Adhesive Seal-
ant to the oil pan and install (Fig. 375). Torque oil
pan-to-transaxle case bolts (Fig. 376) to 19 N´m (165
in. lbs.).
(4) Lower vehicle.
(5) Connect transmission range sensor connector.
(6) Install manual valve lever to manual shaft.
(7) Install gearshift cable to manual valve lever.
(8) Connect battery negative cable.
(9) Fill transaxle with MopartATF +4 Transmis-
sion fluid. (Refer to 21 - TRANSMISSION/TRANS-
AXLE/AUTOMATIC - 41TE/FLUID - STANDARD
PROCEDURE)
Fig. 374 Oil Filter
1 - OIL FILTER
2 - O-RING
Fig. 375 Oil Pan
1 - OIL PAN
2 - 1/8 INCH BEAD OF RTV SEALANT
3 - OIL FILTER
Fig. 376 Oil Pan Bolts
1 - OIL PAN BOLTS (USE RTV UNDER BOLT HEADS)
21 - 296 41TE AUTOMATIC TRANSAXLERS
VALVE BODY (Continued)

CONTROL CIRCUIT TEST - DIAGNOSISAND TESTING ....................... 8F-33
CONTROL, DESCRIPTION - AUTOMATIC TEMPERATURE ....................... 24-3
CONTROL INFORMATION LABEL, DESCRIPTION - VEHICLE EMISSION .......25-1
CONTROL MODULE - DESCRIPTION, BODY ............................... 8E-2
CONTROL MODULE - DESCRIPTION, FRONT .............................. 8E-7
CONTROL MODULE - DESCRIPTION, POWER LIFTGATE .................... 8E-10
CONTROL MODULE - DESCRIPTION, SLIDING DOOR ...................... 8E-18
CONTROL MODULE - INSTALLATION, BODY ............................... 8E-4
CONTROL MODULE - OPERATION, BODY . . . 8E-3
CONTROL MODULE - OPERATION, FRONT .............................. 8E-7
CONTROL MODULE - OPERATION, POWER LIFTGATE .................... 8E-10
CONTROL MODULE - OPERATION, SLIDING DOOR ...................... 8E-18
CONTROL MODULE - REMOVAL, BODY ....8E-4
CONTROL MODULE, DIAGNOSIS AND TESTING - FRONT ..................... 8E-7
CONTROL MODULE, DIAGNOSIS AND TESTING - POWER LIFTGATE ...........8E-10
CONTROL MODULE, DIAGNOSIS AND TESTING - SLIDING DOOR .............8E-18
CONTROL MOTOR - DESCRIPTION, IDLE AIR ............................... 14-33
CONTROL MOTOR - INSTALLATION, IDLE AIR ............................... 14-33
CONTROL MOTOR - OPERATION, IDLE AIR ............................... 14-33
CONTROL MOTOR - REMOVAL, IDLE AIR . . 14-33
CONTROL, OPERATION - AUTOMATIC TEMPERATURE ....................... 24-5
CONTROL RELAY - DESCRIPTION, TRANSMISSION ............... 21-130,21-281
CONTROL RELAY - OPERATION, TRANSMISSION ............... 21-130,21-281
CONTROL SWITCH - DIAGNOSIS AND TESTING, TRACTION ................... 5-94
CONTROL SWITCH - INSTALLATION, TRACTION ........................... 5-95
CONTROL SWITCH - REMOVAL, TRACTION ........................... 5-95
CONTROL SYSTEM - DESCRIPTION, TRACTION ........................... 5-88
CONTROL SYSTEM - OPERATION, EVAPORATION ....................... 25-11
CONTROL SYSTEM - OPERATION, TRACTION ........................... 5-89
CONTROL SYSTEM, OPERATION - AUTOMATIC TEMPERATURE ...........24-114
CONTROL SYSTEM, OPERATION - MANUAL TEMPERATURE ..............24-113
CONTROLLER - DESCRIPTION, OCCUPANT RESTRAINT ...............8O-27
CONTROLLER - INSTALLATION, OCCUPANT RESTRAINT ...............8O-29
CONTROLLER - INSTALLATION, SBEC ....8E-17
CONTROLLER - OPERATION, OCCUPANT RESTRAINT ......................... 8O-28
CONTROLLER - REMOVAL, NGC .........8E-16
CONTROLLER - REMOVAL, OCCUPANT RESTRAINT ......................... 8O-29
CONTROLLER - REMOVAL, SBEC ........8E-16
CONTROLLER ANTILOCK BRAKE - DESCRIPTION ........................ 8E-4
CONTROLLER ANTILOCK BRAKE - INSTALLATION ........................ 8E-6
CONTROLLER ANTILOCK BRAKE - OPERATION .......................... 8E-5
CONTROLLER ANTILOCK BRAKE - REMOVAL ........................... 8E-5
CONVENTIONAL BATTERY CHARGING, STANDARD PROCEDURE ...............8F-11
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-4
CONVERTER - DESCRIPTION, TORQUE . . 21-124,
21-275
CONVERTER - INSPECTION, CATALYTIC ....11-6
CONVERTER - INSTALLATION, CATALYTIC . . 11-6
CONVERTER - INSTALLATION, TORQUE . . 21-129,
21-280
CONVERTER - OPERATION, CATALYTIC ....11-4 CONVERTER - OPERATION, TORQUE
....21-128,
21-278
CONVERTER - REMOVAL, CATALYTIC ......11-5
CONVERTER - REMOVAL, TORQUE .....21-129,
21-280
CONVERTER HOUSING FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE . 21-154,21-9
COOL DOWN TEST, DIAGNOSIS AND TESTING - A/C ........................ 24-6
COOLANT - DESCRIPTION, ENGINE .......7-19
COOLANT - DESCRIPTION, ENGINE ........0-3
COOLANT - STANDARD PROCEDURE, ADDING ADDITIONAL ...................7-4
COOLANT CONCENTRATION TESTING - DIAGNOSIS AND TESTING ..............7-19
COOLANT LEVEL CHECK - STANDARD PROCEDURE ..........................7-4
COOLANT RECOVERY CONTAINER - DESCRIPTION ........................ 7-20
COOLANT RECOVERY CONTAINER - INSTALLATION ........................ 7-20
COOLANT RECOVERY CONTAINER - OPERATION .......................... 7-20
COOLANT RECOVERY CONTAINER - REMOVAL ........................... 7-20
COOLANT RECOVERY SYSTEM - DIAGNOSIS AND TESTING ..............7-20
COOLANT SERVICE - STANDARD PROCEDURE ......................... 7-19
COOLANT TEMPERATURE SENSOR - 2.4L - DESCRIPTION, ENGINE ............7-21
COOLANT TEMPERATURE SENSOR - 2.4L - INSTALLATION, ENGINE .............7-21
COOLANT TEMPERATURE SENSOR - 2.4L - REMOVAL, ENGINE ...............7-21
COOLANT TEMPERATURE SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE .........7-21
COOLANT TEMPERATURE SENSOR - 3.3/3.8L - INSTALLATION, ENGINE ........7-23
COOLANT TEMPERATURE SENSOR - 3.3/3.8L - REMOVAL, ENGINE ............7-21
COOLANT THERMOSTAT - 2.4L - INSTALLATION, ENGINE ................7-24
COOLANT THERMOSTAT - 2.4L - REMOVAL, ENGINE .................... 7-24
COOLANT THERMOSTAT - 3.3/3.8L - INSTALLATION, ENGINE ................7-25
COOLANT THERMOSTAT - 3.3/3.8L - REMOVAL, ENGINE .................... 7-24
COOLANT THERMOSTAT - DESCRIPTION, ENGINE ............................. 7-23
COOLANT THERMOSTAT - DIAGNOSIS AND TESTING, ENGINE .................7-23
COOLANT THERMOSTAT - OPERATION, ENGINE ............................. 7-23
COOLER - DESCRIPTION, FLUID .........19-45
COOLER - DESCRIPTION, TRANSMISSION OIL ................... 7-39
COOLER - INSPECTION, TRANSMISSION OIL ................................ 7-39
COOLER - INSTALLATION, FLUID ........19-45
COOLER & LINES - DESCRIPTION, OIL . . . 9-141
COOLER & LINES - INSTALLATION, OIL . . . 9-141
COOLER & LINES - OPERATION, OIL .....9-141
COOLER & LINES - REMOVAL, OIL .......9-141
COOLER - OPERATION, FLUID ..........19-45
COOLER - REMOVAL, FLUID ............19-45
COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/ASSEMBLY -
STANDARD PROCEDURE,
TRANSMISSION ....................... 7-38
COOLER LINES - INSTALLATION, TRANSMISSION OIL ................... 7-40
COOLER LINES - REMOVAL, TRANSMISSION OIL ................... 7-39
COOLING SYSTEM - DESCRIPTION ........7-1
COOLING SYSTEM - DIAGNOSIS AND TESTING, ENGINE ..................... 7-14
COOLING SYSTEM - OPERATION ..........7-2
COOLING SYSTEM AERATION - DIAGNOSIS AND TESTING ...............7-4
COOLING SYSTEM DEAERATION - DIAGNOSIS AND TESTING ...............7-4
COOLING SYSTEM DRAINING - STANDARD PROCEDURE .................7-4
COOLING SYSTEM FILLING - STANDARD PROCEDURE ..........................7-4 COOLING SYSTEM FLOW CHECK -
DIAGNOSIS AND TESTING ...............7-3
COOLING SYSTEM LEAK TEST - DIAGNOSIS AND TESTING ...............7-2
COOLING SYSTEM PRESSURE CAP TESTING - DIAGNOSIS AND TESTING ......7-28
COOLING SYSTEM REQUIREMENTS, DESCRIPTION - ENGINE ................24-1
COOLING SYSTEM, SPECIAL TOOLS .......7-6
COOLING SYSTEM, WARNING - ENGINE . . 24-65
CORE - DESCRIPTION, HEATER . . . 24-102,24-83
CORE - DESCRIPTION, SERVICE PORT VALVE ............................. 24-95
CORE - INSTALLATION, SERVICE PORT VALVE ............................. 24-95
CORE - OPERATION, HEATER .....24-102,24-84
CORE - REMOVAL, SERVICE PORT VALVE ............................. 24-95
CORE AND OIL GALLERY PLUGS - STANDARD PROCEDURE, ENGINE ....9-10,9-88
CORE FILLING, STANDARD PROCEDURE - REAR HEATER ..................... 24-102
CORE, INSTALLATION - FRONT HEATER . . . 24-86
CORE, REMOVAL - FRONT HEATER ......24-85
CORE TUBES, INSTALLATION - FRONT HEATER ............................ 24-85
CORE TUBES, REMOVAL - FRONT HEATER ............................ 24-84
COURTESY LAMP - INSTALLATION .......8L-21
COURTESY LAMP - REMOVAL ..........8L-21
COVER - CLEANING, CYLINDER HEAD .......9-31
COVER - DESCRIPTION, WHEEL .........22-19
COVER - FOLD-IN-FLOOR - INSTALLATION, CARPET TRIM RING .....23-84
COVER - FOLD-IN-FLOOR - REMOVAL, CARPET TRIM RING .................. 23-84
COVER - INSPECTION, CYLINDER HEAD . . . 9-31
COVER - INSTALLATION, BENCH SEAT BACK ............................. 23-148
COVER - INSTALLATION, CYLINDER HEAD ............................... 9-32
COVER - INSTALLATION, FRONT SEAT BACK ............................. 23-116
COVER - INSTALLATION, FRONT SEAT CUSHION SIDE ..................... 23-121
COVER - INSTALLATION, FRONT SEAT TRACK - REAR ..................... 23-128
COVER - INSTALLATION, INSTRUMENT PANEL TOP ......................... 23-72
COVER - INSTALLATION, LOWER STEERING COLUMN .................. 23-74
COVER - INSTALLATION, OVER STEERING COLUMN .................. 23-76
COVER - INSTALLATION, TIMING CHAIN . . 9-157
COVER - INSTALLATION, WHEEL ........22-20
COVER - LEFT - INSTALLATION, CYLINDER HEAD ..................... 9-107
COVER - LEFT - REMOVAL, CYLINDER HEAD .............................. 9-107
COVER - OCS - INSTALLATION, FRONT SEAT CUSHION SIDE .................23-122
COVER - OCS - INSTALLATION, FRONT SEAT TRACK REAR .................. 23-129
COVER - OCS - REMOVAL, FRONT SEAT CUSHION SIDE ..................... 23-121
COVER - OCS - REMOVAL, FRONT SEAT TRACK REAR ....................... 23-129
COVER - QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT
CUSHION .......................... 23-144
COVER - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT CUSHION .....23-144
COVER - REMOVAL, BENCH SEAT BACK . . 23-148
COVER - REMOVAL, CYLINDER HEAD .....9-31
COVER - REMOVAL, FRONT SEAT BACK . . 23-113
COVER - REMOVAL, FRONT SEAT CUSHION SIDE ..................... 23-120
COVER - REMOVAL, FRONT SEAT TRACK - REAR ............................ 23-128
COVER - REMOVAL, INSTRUMENT PANEL TOP ......................... 23-72
COVER - REMOVAL, LOWER STEERING COLUMN ........................... 23-74
COVER - REMOVAL, OVER STEERING COLUMN ........................... 23-76
COVER - REMOVAL, TIMING CHAIN ......9-156
COVER - REMOVAL, WHEEL ............22-19
8 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FILTER ADAPTER - INSTALLATION, OIL . . . 9-142
FILTER ADAPTER - REMOVAL, OIL.......9-142
FILTER CHANGE - STANDARD PROCEDURE, ENGINE OIL ..........9-139,9-54
FILTER SERVICE - STANDARD PROCEDURE, FLUID ............21-231,21-82
FINAL DRIVE - ASSEMBLY .......21-224,21-78
FINAL DRIVE - DESCRIPTION .....21-219,21-74
FINAL DRIVE - DISASSEMBLY ....21-220,21-75
FINAL DRIVE - OPERATION .......21-220,21-75
FINESSE SANDING/BUFFING & POLISHING - DESCRIPTION ...........23-101
FINISH - DESCRIPTION, BASE COAT/CLEARCOAT ................... 23-101
FIRING ORDER, SPECIFICATIONS .........8I-3
FIRST ROW - BENCH - INSTALLATION, SEAT BELT BUCKLE .................. 8O-37
FIRST ROW - BENCH - REMOVAL, SEAT BELT BUCKLE ....................... 8O-36
FIRST ROW - OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
FIRST ROW - OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR .............8O-39
FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE ......8O-36
FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE .........8O-35
FITTING - CONNECTING ROD ............9-46
FITTING - PISTON RING ................9-47
FITTING - STANDARD PROCEDURE, MAIN BEARING ...................... 9-125
FITTING - STANDARD PROCEDURE, PISTON RING ....................... 9-124
FITTING - STANDARD PROCEDURE, PISTON TO CYLINDER BORE ............9-44
FITTING CONNECTING RODS - STANDARD PROCEDURE ...............9-119
FITTING DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE,
TRANSMISSION COOLER LINE QUICK
CONNECT ............................ 7-38
FITTING PISTONS - STANDARD PROCEDURE ........................ 9-120
FITTINGS - STANDARD PROCEDURE, QUICK-CONNECT ..................... 14-18
FITTINGS, STANDARD PROCEDURE - HANDLING TUBING ................... 24-69
FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD BUCKET SEAT
SIDE SHIELD/CUP HOLDER ............23-151
FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET SEAT SIDE
SHIELD/CUP HOLDER ................23-151
FLEX DRIVE - DESCRIPTION ...........8N-55
FLEX DRIVE - INSTALLATION ...........8N-56
FLEX DRIVE - OPERATION .............8N-55
FLEX DRIVE - REMOVAL ...............8N-55
FLEX PLATE - INSTALLATION ...........9-133
FLEX PLATE - REMOVAL ...............9-133
FLEXIBLE FUEL ENGINE OIL - DESCRIPTION .........................0-3
FLOOR CONSOLE - FOLD-IN-FLOOR - INSTALLATION ....................... 23-89
FLOOR CONSOLE - FOLD-IN-FLOOR - REMOVAL .......................... 23-89
FLOOR CONSOLE BASE TRAY - INSTALLATION ....................... 23-89
FLOOR CONSOLE BASE TRAY - REMOVAL .......................... 23-89
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR DISTRIBUTION DUCTS - INSTALLATION ....................... 24-50
FLOOR DISTRIBUTION DUCTS - REMOVAL .......................... 24-50
FLOOR HEAT DUCT - INSTALLATION, REAR .............................. 24-63
FLOOR HEAT DUCT - REMOVAL, REAR . . . 24-63
FLOOR MATS - INSTALLATION, CARPETS . 23-81
FLOOR MATS - REMOVAL, CARPETS .....23-81 FLOOR TUB CARPET INSERT -
FOLD-IN-FLOOR - INSTALLATION,
SECOND ROW ....................... 23-98
FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND
ROW .............................. 23-98
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION,
REAR .............................. 23-96
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR ......23-95
FLOW AND PRESSURE TEST - DIAGNOSIS AND TESTING, POWER
STEERING SYSTEM .................... 19-1
FLOW CHECK - DIAGNOSIS AND TESTING, COOLING SYSTEM .............7-3
FLUID - DESCRIPTION, AUTOMATIC/ MANUAL TRANSAXLE ...................0-4
FLUID - DESCRIPTION, AWD POWER TRANSFER UNIT .......................0-6
FLUID AND FILTER SERVICE - STANDARD PROCEDURE .........21-231,21-82
FLUID CAPACITIES - SPECIFICATIONS ......0-6
FLUID CONTAMINATION - DIAGNOSIS AND TESTING, BRAKE .................. 5-33
FLUID COOLER - DESCRIPTION .........19-45
FLUID COOLER - INSTALLATION .........19-45
FLUID COOLER - OPERATION ...........19-45
FLUID COOLER - REMOVAL ............19-45
FLUID FILL/CHECK LOCATIONS - DESCRIPTION .........................0-7
FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER
HOUSING ....................... 21-154,21-9
FLUID LEVEL AND CONDITION CHECK, STANDARD PROCEDURE .........21-230,21-82
FLUID LEVEL CHECKING - STANDARD PROCEDURE, BRAKE ................... 5-33
FLUID LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING ........19-44
FLUID LEVEL SWITCH - DESCRIPTION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - INSTALLATION, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - INSTALLATION, WASHER ........................... 8R-11
FLUID LEVEL SWITCH - OPERATION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - REMOVAL, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - REMOVAL, WASHER ........................... 8R-11
FLUID, SPECIFICATIONS - BRAKE .........5-33
FLUIDS - DESCRIPTION, AWD REAR DRIVELINE MODULE ....................0-6
FLUSH MEASUREMENTS - SPECIFICATIONS, GAP ................23-177
FOG LAMP - DIAGNOSIS AND TESTING, FRONT .............................. 8L-7
FOG LAMP - INSTALLATION, FRONT .......8L-8
FOG LAMP - REMOVAL, FRONT ..........8L-8
FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT ........8L-9
FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT .........8L-9
FOLDAWAY MIRROR SWITCH - EXPORT - DESCRIPTION, POWER ..............8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - INSTALLATION, POWER ..............8N-30
FOLDAWAY MIRROR SWITCH - EXPORT - OPERATION, POWER ................8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - REMOVAL, POWER .................. 8N-29
FOLD-IN-FLOOR - INSTALLATION . . . 14-10,14-16
FOLD-IN-FLOOR - INSTALLATION, ARMREST - SECOND ROW ............23-130
FOLD-IN-FLOOR - INSTALLATION, ARMREST ROTATING ASSEMBLY -
SECOND ROW ...................... 23-130
FOLD-IN-FLOOR - INSTALLATION, BOTTOM OF SEAT CUSHION PAN
PANEL-THIRD ROW .................. 23-152
FOLD-IN-FLOOR - INSTALLATION, CARPET TRIM RING AND COVER ........23-84
FOLD-IN-FLOOR - INSTALLATION, CARPETS ........................... 23-83
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........................... 23-89FOLD-IN-FLOOR - INSTALLATION, FLOOR
CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - SECOND ROW .....23-131
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - THIRD ROW ......23-153
FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB CARPETS INSERT ..........23-96
FOLD-IN-FLOOR - INSTALLATION, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - INSTALLATION, SEAT - THIRD ROW ........................ 23-154
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - SECOND ROW ....23-133
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - THIRD ROW ......23-156
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - SECOND ROW .........23-134
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - THIRD ROW ...........23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER - SECOND ROW ..........23-135
FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER LAP BELT ..............23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT - SECOND ROW ...........23-139
FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD - SECOND ROW ...........23-140
FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR TUB CARPET
INSERT ............................ 23-98
FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - INSTALLATION, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - REMOVAL .......14-10,14-13
FOLD-IN-FLOOR - REMOVAL, ARMREST - SECOND ROW ..................... 23-130
FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING ASSEMBLY - SECOND ROW . . 23-130
FOLD-IN-FLOOR - REMOVAL, BOTTOM OF SEAT CUSHION PAN PANEL-THIRD
ROW ............................. 23-152
FOLD-IN-FLOOR - REMOVAL, CARPET TRIM RING AND COVER ...............23-84
FOLD-IN-FLOOR - REMOVAL, CARPETS . . . 23-82
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ........................... 23-89
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - SECOND ROW ..............23-131
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - THIRD ROW ...............23-152
FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB CARPETS INSERT ..........23-95
FOLD-IN-FLOOR - REMOVAL, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - REMOVAL, SEAT - THIRD ROW ........................ 23-153
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - SECOND ROW .........23-133
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - THIRD ROW ...........23-155
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - SECOND ROW ..............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - THIRD ROW ................23-156
FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER - SECOND ROW ...............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER LAP BELT ................... 23-157
RS INDEX13
Description Group-Page Description Group-Page Description Group-Page

OCS - REMOVAL, FRONT SEAT CUSHION . 23-119
OCS - REMOVAL, FRONT SEAT CUSHIONSIDE COVER ....................... 23-121
OCS - REMOVAL, FRONT SEAT RISER - MANUAL .......................... 23-123
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/MANUAL .................23-126
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/POWER .................. 23-124
OCS - REMOVAL, FRONT SEAT TRACK REAR COVER ....................... 23-129
OIL - DESCRIPTION, FLEXIBLE FUEL ENGINE ..............................0-3
OIL - DESCRIPTION, REFRIGERANT ......24-94
OIL - DIESEL ENGINES - DESCRIPTION, ENGINE ..............................0-6
OIL - OPERATION, REFRIGERANT ........24-94
OIL AND FILTER CHANGE - STANDARD PROCEDURE, ENGINE .............9-139,9-54
OIL AND LUBRICANTS - DESCRIPTION, ENGINE ..............................0-1
OIL COOLER - DESCRIPTION, TRANSMISSION ....................... 7-39
OIL COOLER - INSPECTION, TRANSMISSION ....................... 7-39
OIL COOLER & LINES - DESCRIPTION ....9-141
OIL COOLER & LINES - INSTALLATION . . . 9-141
OIL COOLER & LINES - OPERATION ......9-141
OIL COOLER & LINES - REMOVAL .......9-141
OIL COOLER LINES - INSTALLATION, TRANSMISSION ....................... 7-40
OIL COOLER LINES - REMOVAL, TRANSMISSION ....................... 7-39
OIL FILTER - DESCRIPTION .............9-54
OIL FILTER - INSTALLATION ........9-141,9-54
OIL FILTER - REMOVAL ............9-141,9-54
OIL FILTER ADAPTER - INSTALLATION ....9-142
OIL FILTER ADAPTER - REMOVAL .......9-142
OIL GALLERY PLUGS - STANDARD PROCEDURE, ENGINE CORE .........9-10,9-88
OIL LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE ..............9-8,9-84
OIL LEVEL CHECK - STANDARD PROCEDURE, ENGINE .................9-140
OIL LEVEL CHECK, STANDARD PROCEDURE - ENGINE .................9-54
OIL LEVEL, STANDARD PROCEDURE - REFRIGERANT ....................... 24-94
OIL PAN - CLEANING .................9-142
OIL PAN - INSPECTION ................9-143
OIL PAN - INSTALLATION ..........9-143,9-55
OIL PAN - REMOVAL ..............9-142,9-55
OIL PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE ............9-53
OIL PRESSURE - DIAGNOSIS AND TESTING, ENGINE .................... 9-138
OIL PRESSURE RELIEF VALVE - INSTALLATION ....................... 9-144
OIL PRESSURE RELIEF VALVE - REMOVAL .......................... 9-143
OIL PRESSURE SWITCH - DESCRIPTION . . 9-144
OIL PRESSURE SWITCH - INSTALLATION . 9-144, 9-56
OIL PRESSURE SWITCH - OPERATION ....9-144
OIL PRESSURE SWITCH - REMOVAL . 9-144,9-56
OIL PUMP - ASSEMBLY ...........9-146,9-58
OIL PUMP - ASSEMBLY ........21-112,21-263
OIL PUMP - CLEANING ............9-145,9-57
OIL PUMP - DESCRIPTION .............9-144
OIL PUMP - DESCRIPTION ......21-110,21-261
OIL PUMP - DISASSEMBLY ........9-145,9-57
OIL PUMP - DISASSEMBLY ......21-110,21-261
OIL PUMP - INSPECTION ..........9-145,9-58
OIL PUMP - INSTALLATION ........9-146,9-59
OIL PUMP - INSTALLATION, SEAL ......21-113,
21-264
OIL PUMP - OPERATION ........21-110,21-261
OIL PUMP - REMOVAL ............9-144,9-56
OIL PUMP - REMOVAL, SEAL ....21-113,21-264
OIL SEAL - FRONT - INSTALLATION, CRANKSHAFT ................... 9-130,9-42
OIL SEAL - FRONT - REMOVAL, CRANKSHAFT ................... 9-130,9-41
OIL SEAL - REAR - INSTALLATION, CRANKSHAFT ................... 9-131,9-42
OIL SEAL - REAR - REMOVAL, CRANKSHAFT ................... 9-131,9-42OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR .................. 9-132
OIL SEAL RETAINER - REMOVAL, CRANKSHAFT REAR .................. 9-132
OIL SEAL(S) - INSTALLATION, CAMSHAFT .......................... 9-29
OIL SEAL(S) - REMOVAL, CAMSHAFT .....9-28
ON-BOARD DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING ..............8F-22
ONLY - SPECIFICATIONS, BODY SEALING LOCATIONS - FOLD-IN-FLOOR .........23-209
ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS . . . 13-11
ONLY - SPECIFICATIONS, STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-
FLOOR ............................ 23-228
OPEN LATCH - INSTALLATION, HOLD .....23-25
OPEN LATCH - REMOVAL, HOLD ........23-25
OPEN LATCH CABLE - INSTALLATION, HOLD .............................. 23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION, HOLD .............................. 23-26
OPEN LATCH STRIKER - REMOVAL, HOLD .............................. 23-26
OPEN SWITCH - DESCRIPTION, FULL ....8N-11,
8N-52
OPEN SWITCH - INSTALLATION, FULL ....8N-11
OPEN SWITCH - OPERATION, FULL . 8N-11,8N-52
OPEN SWITCH - REMOVAL, FULL .......8N-11
OPEN-CIRCUIT VOLTAGE TEST, STANDARD PROCEDURE ................8F-13
OPENING DIMENSIONS - SPECIFICATIONS, BODY ..............23-180
ORVR - OPERATION ..................25-15
OUTER BELT MOLDING - INSTALLATION, FRONT DOOR ...................... 23-167
OUTER BELT MOLDING - REMOVAL, FRONT DOOR ...................... 23-167
OUTER TIE ROD - INSTALLATION ........19-35
OUTER TIE ROD - REMOVAL ...........19-34
OUTLET - DESCRIPTION, POWER ......8W-97-3
OUTLET - DIAGNOSIS & TESTING, POWER ..........................8W -97-3
OUTLET - OPERATION, POWER .......8W-97-3
OUTLETS - DESCRIPTION, AIR .....24-43,24-56
OUTLETS - INSTALLATION, AIR .........24-56
OUTLETS - REMOVAL, AIR .............24-56
OUTLETS, INSTALLATION - FRONT CENTER BEZEL ...................... 24-45
OUTLETS, INSTALLATION - FRONT DEMISTER .......................... 24-45
OUTLETS, INSTALLATION - INSTRUMENT PANEL ............................. 24-45
OUTLETS, REMOVAL - FRONT CENTER BEZEL ............................. 24-44
OUTLETS, REMOVAL - FRONT DEMISTER . 24-44
OUTLETS, REMOVAL - INSTRUMENT PANEL ............................. 24-45
OUTPUT - DESCRIPTION, SPEED SENSOR ..................... 21-122,21-273
OUTPUT - INSTALLATION, SPEED SENSOR ..................... 21-123,21-274
OUTPUT - OPERATION, 5 VOLT SUPPLY - PCM............................... 8E-15
OUTPUT - OPERATION, SPEED SENSOR . 21-122, 21-273
OUTPUT - REMOVAL, SPEED SENSOR . . 21-123,
21-274
OUTSIDE HANDLE - INSTALLATION ......23-36
OUTSIDE HANDLE - REMOVAL ..........23-35
OUTSIDE HANDLE CABLE - INSTALLATION ....................... 23-37
OUTSIDE HANDLE CABLE - REMOVAL ....23-37
OVER STEERING COLUMN COVER - INSTALLATION ....................... 23-76
OVER STEERING COLUMN COVER - REMOVAL .......................... 23-76
OVERHEAD CONSOLE - DESCRIPTION ....8M-2
OVERHEAD CONSOLE, DIAGNOSIS AND TESTING ............................ 8M-3
OVERHEAD CONSOLE, SPECIAL TOOLS . . . 8M-7
PAD - INSTALLATION, REAR FASCIA - SCUFF .............................. 13-5
PAD - REMOVAL, REAR FASCIA - SCUFF . . . 13-5
PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL TOP ..............23-77PAD ASSEMBLY - REMOVAL,
INSTRUMENT PANEL TOP ..............23-77
PAINT CODE - DESCRIPTION ..........23-101
PAINTED TOUCH-UP - DESCRIPTION ....23-101
PAN - CLEANING, OIL .................9-142
PAN - INSPECTION, OIL ...............9-143
PAN - INSTALLATION, OIL .........9-143,9-55
PAN - REMOVAL, OIL .............9-142,9-55
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - INSTALLATION, BOTTOM OF
SEAT CUSHION ..................... 23-152
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - REMOVAL, BOTTOM OF SEAT
CUSHION .......................... 23-152
PANEL - INSTALLATION, BENCH SEAT BACK ............................. 23-144
PANEL - INSTALLATION, FRONT SEAT BACK ............................. 23-113
PANEL - INSTALLATION, GLASS ........23-173
PANEL - INSTALLATION, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - INSTALLATION, LEFT QUARTER TRIM .............................. 23-94
PANEL - INSTALLATION, LOWER INSTRUMENT ....................... 23-73
PANEL - INSTALLATION, RIGHT D-PILLAR TRIM ...................... 23-98
PANEL - INSTALLATION, RIGHT QUARTER TRIM ...................... 23-97
PANEL - INSTALLATION, TRIM .....23-20,23-34,
23-43
PANEL - REMOVAL, BENCH SEAT BACK . . . 23-143
PANEL - REMOVAL, FRONT SEAT BACK . . 23-112
PANEL - REMOVAL, GLASS ............23-173
PANEL - REMOVAL, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - REMOVAL, LEFT QUARTER TRIM .............................. 23-94
PANEL - REMOVAL, LOWER INSTRUMENT ....................... 23-73
PANEL - REMOVAL, RIGHT D-PILLAR TRIM .............................. 23-97
PANEL - REMOVAL, RIGHT QUARTER TRIM .............................. 23-97
PANEL - REMOVAL, TRIM ....23-20,23-34,23-43
PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-134
PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-134
PANEL - THIRD ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ............23-158
PANEL - THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ...............23-158
PANEL ADJUSTMENT, ADJUSTMENTS - SUNROOF GLASS ................... 23-173
PANEL ANTENNA CABLE - INSTALLATION, INSTRUMENT ...........8A-12
PANEL ANTENNA CABLE - REMOVAL, INSTRUMENT ....................... 8A-12
PANEL ASSEMBLY - INSTALLATION, INSTRUMENT ....................... 23-70
PANEL ASSEMBLY - REMOVAL, INSTRUMENT ....................... 23-67
PANEL CENTER BEZEL - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL CENTER BEZEL - REMOVAL, INSTRUMENT ....................... 23-71
PANEL DEMISTER DUCTS - INSTALLATION, INSTRUMENT ...........24-54
PANEL DEMISTER DUCTS - REMOVAL, INSTRUMENT ....................... 24-54
PANEL DUCTS - INSTALLATION, INSTRUMENT ....................... 24-55
PANEL DUCTS - REMOVAL, INSTRUMENT ....................... 24-55
PANEL OUTLETS, INSTALLATION - INSTRUMENT ....................... 24-45
PANEL OUTLETS, REMOVAL - INSTRUMENT ....................... 24-45
PANEL REPAIR - STANDARD PROCEDURE, PLASTIC BODY ............23-3
PANEL RIGHT END CAP - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL RIGHT END CAP - REMOVAL, INSTRUMENT ....................... 23-72
PANEL TOP COVER - INSTALLATION, INSTRUMENT ....................... 23-72
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

QUAD BUCKET - REMOVAL, BUCKETSEAT BACK ........................ 23-140
QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE - FIRST ROW INBOARD ........8O-35
QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT BACK HINGE
COVERS ........................... 23-146
QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT CUSHION COVER . . 23-144
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK HINGE COVERS . . 23-146
QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT CUSHION COVER ......23-144
QUAD BUCKET SEAT RISER - INSTALLATION ...................... 23-143
QUAD BUCKET SEAT RISER - REMOVAL . 23-143
QUAD BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - INSTALLATION .........23-143
QUAD BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - REMOVAL .............23-143
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - INSTALLATION ...........23-151
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - REMOVAL ...............23-151
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - INSTALLATION .............23-142
QUAD BUCKET SEAT SIDE SHIELD/CUP HOLDER - REMOVAL .................23-141
QUAD CHILD SEAT - INSTALLATION .....23-106
QUAD CHILD SEAT - REMOVAL ........23-106
QUAD SEAT CUSHION - INSTALLATION . . 23-141
QUAD SEAT CUSHION - REMOVAL ......23-141
QUARTER GLASS INTEGRAL ANTENNA - EXPORT - DESCRIPTION ...............8A-13
QUARTER GLASS INTEGRAL ANTENNA - EXPORT - OPERATION ................8A-13
QUARTER GLASS INTEGRAL ANTENNA, EXPORT ............................ 8A-13
QUARTER PANEL/FENDER AIR EXHAUSTER - DESCRIPTION, REAR ......23-59
QUARTER PANEL/FENDER AIR EXHAUSTER - INSTALLATION, REAR .....23-60
QUARTER PANEL/FENDER AIR EXHAUSTER - REMOVAL, REAR .........23-59
QUARTER TRIM BOLSTER - INSTALLATION ....................... 23-95
QUARTER TRIM BOLSTER - REMOVAL ....23-95
QUARTER TRIM PANEL - INSTALLATION, LEFT .............................. 23-94
QUARTER TRIM PANEL - INSTALLATION, RIGHT ............................. 23-97
QUARTER TRIM PANEL - REMOVAL, LEFT .............................. 23-94
QUARTER TRIM PANEL - REMOVAL, RIGHT ............................. 23-97
QUARTER WINDOW - INSTALLATION ....23-164
QUARTER WINDOW - REMOVAL ........23-164
QUICK CONNECT FITTING DISASSEMBLY/ASSEMBLY -
STANDARD PROCEDURE,
TRANSMISSION COOLER LINE ...........7-38
QUICK LEARN PROCEDURE - STANDARD PROCEDURE ........................ 8E-15
QUICK-CONNECT FITTINGS - STANDARD PROCEDURE ........................ 14-18
RACK - DESCRIPTION, LOWER DRIVE UNIT TRACK ........................ 8N-57
RACK - INSTALLATION, LOWER DRIVE UNIT TRACK ........................ 8N-58
RACK - OPERATION, LOWER DRIVE UNIT TRACK ............................. 8N-57
RACK - REMOVAL, LOWER DRIVE UNIT TRACK ............................. 8N-57
RACK CROSSBAR - INSTALLATION, LUGGAGE .......................... 23-59
RACK CROSSBAR - REMOVAL, LUGGAGE . 23-58
RACK RISER - INSTALLATION, LUGGAGE . . 23-58
RACK RISER - REMOVAL, LUGGAGE .....23-57
RADIAL-PLY TIRES - DESCRIPTION ......22-13
RADIATOR - INSTALLATION .............7-27
RADIATOR - REMOVAL .................7-26
RADIATOR CAP TO FILLER NECK SEAL - DIAGNOSIS AND TESTING ..............7-28
RADIATOR CROSSMEMBER - INSTALLATION, UPPER ................23-56RADIATOR CROSSMEMBER - REMOVAL,
UPPER ............................. 23-56
RADIATOR DRAINCOCK - INSTALLATION . . . 7-27
RADIATOR DRAINCOCK - REMOVAL .......7-27
RADIATOR FAN - DESCRIPTION ..........7-29
RADIATOR FAN - INSTALLATION ..........7-30
RADIATOR FAN - OPERATION ............7-29
RADIATOR FAN - REMOVAL .............7-30
RADIATOR FAN MOTOR - DIAGNOSIS AND TESTING ........................ 7-30
RADIATOR FAN RELAY - DESCRIPTION ....7-31
RADIATOR FAN RELAY - INSTALLATION ....7-31
RADIATOR FAN RELAY - OPERATION ......7-31
RADIATOR FAN RELAY - REMOVAL .......7-31
RADIATOR PRESSURE CAP - DESCRIPTION ........................ 7-27
RADIATOR PRESSURE CAP - OPERATION . . 7-27
RADIO - DESCRIPTION ................8A-13
RADIO - INSTALLATION, ANTENNA - NAVIGATION ........................ 8A-11
RADIO - OPERATION ..................8A-14
RADIO - REMOVAL, ANTENNA - NAVIGATION ........................ 8A-11
RADIO, DIAGNOSIS AND TESTING .......8A-14
RADIO NOISE SUPPRESSION COMPONENTS - DESCRIPTION ..........8A-15
RADIO NOISE SUPPRESSION COMPONENTS - OPERATION ...........8A-15
RANGE - SPECIFICATIONS, TRANSMITTER ...................... 8N-24
RANGE SENSOR - DESCRIPTION, TRANSMISSION ............... 21-130,21-281
RANGE SENSOR - INSTALLATION, TRANSMISSION ............... 21-131,21-282
RANGE SENSOR - OPERATION, TRANSMISSION ............... 21-131,21-282
RANGE SENSOR - REMOVAL, TRANSMISSION ............... 21-131,21-282
READING LAMP - INSTALLATION ........8L-23
READING LAMP - REMOVAL ............8L-22
RECEIVER / DRIER - DESCRIPTION ......24-92
RECEIVER / DRIER - INSTALLATION ......24-93
RECEIVER / DRIER - OPERATION ........24-92
RECEIVER / DRIER - REMOVAL .........24-92
RECIRCULATION DOOR ACTUATOR - DESCRIPTION ....................... 24-31
RECIRCULATION DOOR ACTUATOR - INSTALLATION ....................... 24-32
RECIRCULATION DOOR ACTUATOR - OPERATION ......................... 24-31
RECIRCULATION DOOR ACTUATOR - REMOVAL .......................... 24-32
RECLINER HANDLE - INSTALLATION ....23-108
RECLINER HANDLE - REMOVAL ........23-108
RECLINER/FOLD FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR -
INSTALLATION, SEAT .................23-160
RECLINER/FOLD FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR -
REMOVAL, SEAT .................... 23-160
RECLINER/FORWARD FOLDING MECHANISM -SECOND ROW
-FOLD-IN-FLOOR - INSTALLATION,
SEAT ............................. 23-137
RECLINER/FORWARD FOLDING MECHANISM -SECOND ROW
-FOLD-IN-FLOOR - REMOVAL, SEAT .....23-137
RECOVERY CONTAINER - DESCRIPTION, COOLANT ............................ 7-20
RECOVERY CONTAINER - INSTALLATION, COOLANT ............................ 7-20
RECOVERY CONTAINER - OPERATION, COOLANT ............................ 7-20
RECOVERY CONTAINER - REMOVAL, COOLANT ............................ 7-20
RECOVERY, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-70
RECOVERY SYSTEM - DIAGNOSIS AND TESTING, COOLANT ................... 7-20
REFACING VALVES AND VALVE SEATS - STANDARD PROCEDURE ...............9-107
REFRIGERANT - DESCRIPTION ..........24-93
REFRIGERANT - OPERATION ............24-94
REFRIGERANT LINES, INSTALLATION - UNDERBODY ....................... 24-112
REFRIGERANT LINES, REMOVAL - UNDERBODY ....................... 24-110
REFRIGERANT OIL - DESCRIPTION ......24-94 REFRIGERANT OIL - OPERATION
........24-94
REFRIGERANT OIL LEVEL, STANDARD PROCEDURE ........................ 24-94
REFRIGERANT SYSTEM CHARGE, STANDARD PROCEDURE ...............24-71
REFRIGERANT SYSTEM EVACUATE, STANDARD PROCEDURE ...............24-70
REFRIGERANT SYSTEM LEAKS, DIAGNOSIS AND TESTING .............24-67
REFRIGERANT SYSTEM RECOVERY, STANDARD PROCEDURE ...............24-70
REFRIGERANT SYSTEM SERVICE EQUIPMENT, STANDARD PROCEDURE ....24-69
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-30
REGULATOR - INSTALLATION, FUEL PRESSURE .......................... 14-7
REGULATOR - MANUAL - INSTALLATION, WINDOW ........................... 23-23
REGULATOR - MANUAL - REMOVAL, WINDOW ........................... 23-22
REGULATOR - OPERATION, FUEL PRESSURE .......................... 14-7
REGULATOR - OPERATION, VOLTAGE .....8F-30
REGULATOR - POWER - INSTALLATION, WINDOW ........................... 23-22
REGULATOR - POWER - REMOVAL, WINDOW ........................... 23-22
REGULATOR - REMOVAL, FUEL PRESSURE .......................... 14-7
REINFORCEMENT - INSTALLATION, FRONT BUMPER ...................... 13-3
REINFORCEMENT - INSTALLATION, REAR BUMPER .............................. 13-5
REINFORCEMENT - REMOVAL, FRONT BUMPER ............................ 13-3
REINFORCEMENT - REMOVAL, REAR BUMPER ............................ 13-5
RELAY - DESCRIPTION, A/C COMPRESSOR CLUTCH ...............24-18
RELAY - DESCRIPTION, AUTO SHUT DOWN .............................. 8I-3
RELAY - DESCRIPTION, BLOWER MOTOR ....................... 24-23,24-36
RELAY - DESCRIPTION, FUEL PUMP .....14-32
RELAY - DESCRIPTION, RADIATOR FAN ....7-31
RELAY - DESCRIPTION, REAR WINDOW DEFOGGER .......................... 8G-3
RELAY - DESCRIPTION, TRANSMISSION CONTROL ................... 21-130,21-281
RELAY - INSTALLATION, A/C COMPRESSOR CLUTCH ...............24-19
RELAY - INSTALLATION, BLOWER MOTOR ....................... 24-24,24-37
RELAY - INSTALLATION, RADIATOR FAN . . . 7-31
RELAY - INSTALLATION, REAR WINDOW DEFOGGER .......................... 8G-4
RELAY - OPERATION, A/C COMPRESSOR CLUTCH ............................ 24-18
RELAY - OPERATION, AUTO SHUT DOWN . . . 8I-3
RELAY - OPERATION, BLOWER MOTOR . . 24-23, 24-36
RELAY - OPERATION, FUEL PUMP .......14-32
RELAY - OPERATION, RADIATOR FAN ......7-31
RELAY - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-3
RELAY - OPERATION, TRANSMISSION CONTROL ................... 21-130,21-281
RELAY - REMOVAL, A/C COMPRESSOR CLUTCH ............................ 24-19
RELAY - REMOVAL, BLOWER MOTOR ....24-24,
24-37
RELAY - REMOVAL, RADIATOR FAN .......7-31
RELAY - REMOVAL, REAR WINDOW DEFOGGER .......................... 8G-4
RELEASE - STANDARD PROCEDURE, PARKING BRAKE AUTOMATIC
ADJUSTER TENSION ................... 5-63
RELEASE CABLE - INSTALLATION, LATCH . 23-64
RELEASE CABLE - REMOVAL, LATCH .....23-63
RELEASE PROCEDURE - STANDARD PROCEDURE, FUEL SYSTEM
PRESSURE .......................... 14-2
RELIEF VALVE - INSTALLATION, OIL PRESSURE ......................... 9-144
RELIEF VALVE - REMOVAL, OIL PRESSURE ......................... 9-143
RELIEF VALVE, DESCRIPTION - HIGH PRESSURE ......................... 24-72
RS INDEX25
Description Group-Page Description Group-Page Description Group-Page

SEAT STORAGE BIN GUIDE - REMOVAL,UNDER ............................ 23-150
SEAT STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER ...............23-150
SEAT STORAGE BIN LOCK/LATCH - REMOVAL, UNDER .................. 23-150
SEAT SWITCH - DESCRIPTION ..........8N-34
SEAT SWITCH - DESCRIPTION, HEATED . . . 8G-8
SEAT SWITCH - OPERATION ............8N-34
SEAT SWITCH - OPERATION, HEATED .....8G-9
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER ................... 8N-34
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED .............8G-9
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-7
SEAT SYSTEM - OPERATION, HEATED .....8G-8
SEAT SYSTEM, DESCRIPTION - POWER . . 8N-31
SEAT SYSTEM, DIAGNOSIS AND TESTING - HEATED .................... 8G-8
SEAT SYSTEM, DIAGNOSIS AND TESTING - POWER ................... 8N-33
SEAT SYSTEM, OPERATION - POWER ....8N-32
SEAT TRACK - DESCRIPTION, POWER ....8N-37
SEAT TRACK - INSTALLATION, BENCH . . . 23-148
SEAT TRACK - OPERATION, POWER .....8N-38
SEAT TRACK - REAR COVER - INSTALLATION, FRONT ...............23-128
SEAT TRACK - REAR COVER - REMOVAL, FRONT ................... 23-128
SEAT TRACK - REMOVAL, BENCH ........23-148
SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT ..............23-128
SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT .................23-126
SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT ...............23-125
SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT ................... 23-124
SEAT TRACK, DIAGNOSIS AND TESTING - POWER ........................... 8N-38
SEAT TRACK MANUAL ADJUSTER - INSTALLATION, FRONT ...............23-126
SEAT TRACK MANUAL ADJUSTER - REMOVAL, FRONT ................... 23-125
SEAT TRACK POWER ADJUSTER - INSTALLATION, FRONT ...............23-124
SEAT TRACK POWER ADJUSTER - REMOVAL, FRONT ................... 23-124
SEAT TRACK REAR COVER - OCS - INSTALLATION, FRONT ...............23-129
SEAT TRACK REAR COVER - OCS - REMOVAL, FRONT ................... 23-129
SEAT WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION ..............8O-43
SEAT WEIGHT BLADDER & PRESSURE SENSOR - OPERATION ................8O-44
SEATING - INSTALLATION, FOLD-IN- FLOOR .......................... 5-68,5-75
SEATING - INSTALLATION, FWD - FOLD-IN-FLOOR ....................... 2-45
SEATING - REMOVAL, FOLD-IN-FLOOR . 5-66,5-72
SEATING - REMOVAL, FWD - FOLD-IN- FLOOR .............................. 2-45
SEAT/MIRROR MODULE - DESCRIPTION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE - OPERATION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE, DIAGNOSIS AND TESTING - MEMORY ...............8E-9
SEATS - CLEANING, INTAKE/EXHAUST VALVES ........................ 9-108,9-33
SEATS - DESCRIPTION, INTAKE/ EXHAUST VALVES ................ 9-107,9-33
SEATS - INSPECTION, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - INSTALLATION, INTAKE/ EXHAUST VALVES .................... 9-109
SEATS - OPERATION, INTAKE/EXHAUST VALVES ............................ 9-107
SEATS - REMOVAL, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - STANDARD PROCEDURE, REFACING VALVES AND VALVE ..........9-107
SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR .........13-11
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, ARMREST ............23-130SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE .....23-131
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT .................23-132
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/
FOAM ............................. 23-133
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME .....23-134
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER ......23-135
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT ......23-139
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD .......23-140
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ................23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE .........23-131
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT .................... 23-132
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM ....23-133
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME .........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER ..........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT ..........23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD ...........23-139
SECOND ROW - INSTALLATION, BENCH SEAT RISER ........................ 23-145
SECOND ROW - LEFT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-42
SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-42
SECOND ROW - REMOVAL, BENCH SEAT RISER ............................ 23-145
SECOND ROW - RIGHT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-40
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-41
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR .............8O-41
SECOND ROW - THREE PASSENGER BENCH - INSTALLATION, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW - THREE PASSENGER BENCH - REMOVAL, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR -
INSTALLATION ....................... 23-98
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL ....23-98
SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK PANEL ......23-134
SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK PANEL .........23-134
SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT BELT BUCKLE ....8O-38
SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT BUCKLE ........8O-37
SECTION IDENTIFICATION AND INFORMATION - DESCRIPTION ........8W-01-6
SECURITY - DESCRIPTION, VEHICLE THEFT .............................. 8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-1SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT ..............8Q-3
SELF-DIAGNOSTICS - DIAGNOSIS AND TESTING ............................ 8J-2
SENDING UNIT / SENSOR - DESCRIPTION, FUEL LEVEL .............14-5
SENDING UNIT / SENSOR - INSTALLATION, FUEL LEVEL .............14-6
SENDING UNIT / SENSOR - OPERATION, FUEL LEVEL .......................... 14-5
SENDING UNIT / SENSOR - REMOVAL, FUEL LEVEL .......................... 14-5
SENSE - PCM INPUT - OPERATION, IGNITION ........................... 8E-14
SENSITIVE DEVICES - STANDARD PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD) .................8W -01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ........7-21
SENSOR - 3.3/3.8L - INSTALLATION, ENGINE COOLANT TEMPERATURE ........7-23
SENSOR - 3.3/3.8L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - AWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-92
SENSOR - AWD - REMOVAL, REAR WHEEL SPEED ........................ 5-92
SENSOR - DESCRIPTION, AMBIENT TEMP ............................. 8M-12
SENSOR - DESCRIPTION, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - DESCRIPTION, BELT TENSION . . 8O-8
SENSOR - DESCRIPTION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - DESCRIPTION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - DESCRIPTION, ENGINE SPEED . 14-30
SENSOR - DESCRIPTION, EVAPORATOR TEMPERATURE ...................... 24-26
SENSOR - DESCRIPTION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-13
SENSOR - DESCRIPTION, IMPACT .......8O-18
SENSOR - DESCRIPTION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - DESCRIPTION, INLET AIR TEMPERATURE ...................... 14-34
SENSOR - DESCRIPTION, KNOCK .........8I-8
SENSOR - DESCRIPTION, MAP ..........14-34
SENSOR - DESCRIPTION, O2 ...........14-36
SENSOR - DESCRIPTION, PARK ASSIST . . . 8B-6
SENSOR - DESCRIPTION, PINCH ........8N-17
SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-43
SENSOR - DESCRIPTION, THROTTLE POSITION .......................... 14-40
SENSOR - DESCRIPTION, TRANSMISSION RANGE ........21-130,21-281
SENSOR - DIAGNOSIS AND TESTING, TIRE PRESSURE ..................... 22-11
SENSOR - FWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-93
SENSOR - FWD - REMOVAL, REAR WHEEL SPEED ........................ 5-93
SENSOR - INPUT - DESCRIPTION, SPEED ...................... 21-120,21-271
SENSOR - INPUT - INSTALLATION, SPEED ...................... 21-121,21-272
SENSOR - INPUT - OPERATION, SPEED . 21-120, 21-271
SENSOR - INPUT - REMOVAL, SPEED . . . 21-121, 21-272
SENSOR - INSTALLATION, FRONT WHEEL SPEED ........................ 5-92
SENSOR - INSTALLATION, FUEL LEVEL SENDING UNIT ....................... 14-6
SENSOR - INSTALLATION, IMPACT ......8O-21
SENSOR - INSTALLATION, PARK ASSIST . . . 8B-6
SENSOR - INSTALLATION, PINCH ........8N-18
SENSOR - INSTALLATION, TRANSMISSION RANGE ........21-131,21-282
SENSOR - OPERATION, AMBIENT TEMP . . 8M-12
28 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SENSOR - OPERATION, BATTERYTEMPERATURE ...................... 8F-24
SENSOR - OPERATION, BELT TENSION ....8O-9
SENSOR - OPERATION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - OPERATION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - OPERATION, ENGINE SPEED . . . 14-30
SENSOR - OPERATION, EVAPORATOR TEMPERATURE ...................... 24-27
SENSOR - OPERATION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - OPERATION, HEATED SEAT ....8G-13
SENSOR - OPERATION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - OPERATION, KNOCK ...........8I-8
SENSOR - OPERATION, MAP ...........14-34
SENSOR - OPERATION, O2 .............14-36
SENSOR - OPERATION, PARK ASSIST .....8B-6
SENSOR - OPERATION, PINCH ..........8N-17
SENSOR - OPERATION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-44
SENSOR - OPERATION, THROTTLE POSITION .......................... 14-41
SENSOR - OPERATION, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - OUTPUT - DESCRIPTION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - INSTALLATION, SPEED ...................... 21-123,21-274
SENSOR - OUTPUT - OPERATION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - REMOVAL, SPEED . 21-123, 21-274
SENSOR - REMOVAL, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - REMOVAL, CRANKSHAFT POSITION .......................... 14-30
SENSOR - REMOVAL, FRONT WHEEL SPEED .............................. 5-91
SENSOR - REMOVAL, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - REMOVAL, IMPACT ..........8O-19
SENSOR - REMOVAL, PARK ASSIST ......8B-6
SENSOR - REMOVAL, PINCH ...........8N-18
SENSOR - REMOVAL, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - SPECIFICATIONS, BATTERY TEMPERATURE ...................... 8F-23
SENSOR - TPM - CAUTION .............22-11
SENSOR - TPM - DESCRIPTION .........22-10
SENSOR - TPM - INSTALLATION ........22-11
SENSOR - TPM - OPERATION ...........22-10
SENSOR - TPM - REMOVAL ............22-11
SENSOR AIR GAP, SPECIFICATIONS - WHEEL SPEED ........................ 5-91
SENSOR CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE .....8M-12
SENSOR, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE ..............8M-12
SENSOR, DIAGNOSIS AND TESTING - HEATED SEAT ....................... 8G-13
SENSOR RETURN - PCM INPUT - OPERATION ......................... 8E-14
SENTRY KEY REMOTE ENTRY MODULE - DESCRIPTION ........................ 8Q-3
SENTRY KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING ..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE - INSTALLATION ....................... 8Q-6
SENTRY KEY REMOTE ENTRY MODULE - OPERATION .......................... 8Q-4
SENTRY KEY REMOTE ENTRY MODULE - REMOVAL ........................... 8Q-6
SENTRY KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
SERVO - DESCRIPTION .................8P-4
SERVO - INSTALLATION ................8P-4
SERVO - OPERATION ..................8P-4
SERVO - REMOVAL .................... 8P-4
SETTING - STANDARD PROCEDURE, PINION FACTOR ...................... 8E-15
SETTING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
SEVERAL LOADS - STANDARD PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHACKLE - INSTALLATION, SPRING .......2-44 SHACKLE - REMOVAL, SPRING
..........2-44
SHAFT - ASSEMBLY, ROCKER ARMS .....9-113
SHAFT - DIAGNOSIS AND TESTING, HALF ................................3-1
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-113
SHAFT - FRONT - DESCRIPTION, HALF .....3-1
SHAFT - FRONT - INSTALLATION, HALF .....3-4
SHAFT - FRONT - REMOVAL, HALF ........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . . 3-6
SHAFT - INSTALLATION, ROCKER ARMS . . 9-113
SHAFT - REMOVAL, ROCKER ARMS ......9-112
SHAFT - RHD - INSTALLATION, PEDAL TORQUE ............................ 5-44
SHAFT - RHD - REMOVAL, PEDAL TORQUE ............................ 5-44
SHAFTS AND CARRIER ASSEMBLY - DESCRIPTION, BALANCE ................9-71
SHAFTS AND CARRIER ASSEMBLY - INSTALLATION, BALANCE ...............9-73
SHAFTS AND CARRIER ASSEMBLY - OPERATION, BALANCE .................9-71
SHAFTS AND CARRIER ASSEMBLY - REMOVAL, BALANCE ................... 9-71
SHIELD - INSTALLATION, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT
SIDE ............................. 23-143
SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE ............23-143
SHIELD - REMOVAL, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT
CUSHION SIDE ..................... 23-138
SHIELD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT CUSHION
SIDE ............................. 23-138
SHIELD CUP HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE ...............23-160
SHIELD CUP HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE ................... 23-160
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE ............23-151
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE .................. 23-151
SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE ............23-142
SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE .................. 23-141
SHIELDS - DESCRIPTION, HEAT ..........11-7
SHIELDS - INSTALLATION, HEAT .........11-7
SHIELDS - OPERATION, HEAT ............11-7
SHIELDS - REMOVAL, HEAT .............11-7
SHIFT CABLE - INSTALLATION, GEAR ....21-234
SHIFT CABLE - REMOVAL, GEAR . . 21-233,21-84
SHIFT INTERLOCK SOLENOID - DESCRIPTION ................ 21-113,21-264
SHIFT INTERLOCK SOLENOID - DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION ............... 21-115,21-266
SHIFT INTERLOCK SOLENOID - INSTALLATION ................ 21-116,21-267
SHIFT INTERLOCK SOLENOID - OPERATION .................. 21-114,21-265
SHIFT INTERLOCK SOLENOID - REMOVAL ................... 21-115,21-266
SHOCK ABSORBER - DESCRIPTION .......2-36
SHOCK ABSORBER - INSTALLATION ......2-38
SHOCK ABSORBER - OPERATION .........2-36
SHOCK ABSORBER - REMOVAL ..........2-36
SHOCK ABSORBER (UPPER BUSHING) - ASSEMBLY .......................... 2-37
SHOCK ABSORBER (UPPER BUSHING) - DISASSEMBLY ........................ 2-37
SHOE LINING - INSPECTION, REAR DRUM BRAKE ........................ 5-22
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-85
SHOES - ADJUSTMENT, REAR DRUM BRAKE .............................. 5-23
SHOES - CLEANING, DISC BRAKE ....5-16,5-18
SHOES - INSPECTION, DISC BRAKE . . . 5-16,5-18
SHOES - INSTALLATION, REAR DISC BRAKE .............................. 5-19
SHOES - INSTALLATION, REAR DRUM BRAKE .............................. 5-22SHOES - PARKING BRAKE -
INSTALLATION ........................ 5-84
SHOES - PARKING BRAKE - REMOVAL ....5-78
SHOES - REMOVAL, REAR DISC BRAKE ....5-17
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19
SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT DISC BRAKE ......5-16
SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC BRAKE ..........5-15
SHOES (TRW BRAKES) - INSTALLATION, FRONT DISC BRAKE ................... 5-17
SHOES (TRW BRAKES) - REMOVAL, FRONT DISC BRAKE ................... 5-15
SHORT TO GROUND - STANDARD PROCEDURE, TESTING FOR A ........8W-01-9
SHORT TO GROUND ON FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ..........................8W -01-10
SHROUD - LOWER - INSTALLATION ......19-21
SHROUD - LOWER - REMOVAL .........19-21
SHROUD - UPPER - INSTALLATION ......19-22
SHROUD - UPPER - REMOVAL ..........19-22
SHUT DOWN RELAY - DESCRIPTION, AUTO ............................... 8I-3
SHUT DOWN RELAY - OPERATION, AUTO . . . 8I-3
SIDE - INSTALLATION, BODY ...........23-44
SIDE - INSTALLATION, LIFTGATE ........23-44
SIDE - REMOVAL, BODY ...............23-44
SIDE - REMOVAL, LIFTGATE ............23-44
SIDE COVER - INSTALLATION, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - OCS - INSTALLATION, FRONT SEAT CUSHION ...............23-122
SIDE COVER - OCS - REMOVAL, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - REMOVAL, FRONT SEAT CUSHION .......................... 23-120
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY .....23-45
SIDE SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-143
SIDE SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT ........23-143
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT
CUSHION .......................... 23-138
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT
CUSHION .......................... 23-138
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - INSTALLATION ..............23-160
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - REMOVAL .................. 23-160
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT .................23-151
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT ...................... 23-151
SIDE SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-142
SIDE SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT .................23-141
SIDE VIEW MIRROR - INSTALLATION .....23-60
SIDE VIEW MIRROR - REMOVAL ........23-60
SIDEVIEW MIRROR - REMOVAL .........8N-30
SIGNAL LAMP - INSTALLATION, PARK/TURN ......................... 8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN ....8L-17
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-95
SILL PLATE - INSTALLATION, SLIDING DOOR ............................. 23-99
SILL PLATE - REMOVAL, LIFTGATE .......23-94
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-98
SILL TRIM PLATE - INSTALLATION, DOOR ............................. 23-89
SILL TRIM PLATE - REMOVAL, DOOR ....23-89
SINGLE ZONE, DESCRIPTION - MANUAL . . . 24-2
SINGLE ZONE, OPERATION - MANUAL .....24-4
SLEEVE - INSTALLATION, HEADREST ....23-107
SLEEVE - REMOVAL, HEADREST .......23-107
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, HEADREST ....23-131
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, HEADREST ........23-131
RS INDEX29
Description Group-Page Description Group-Page Description Group-Page

TO CYLINDER BORE FITTING -STANDARD PROCEDURE, PISTON ........9-44
TO FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP ...........7-28
TO GROUND - STANDARD PROCEDURE, TESTING FOR A SHORT .............8W-01-9
TO GROUND ON FUSES POWERING SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS - DESCRIPTION, HOW ................8W -01-1
TONE WHEEL - INSPECTION .............5-94
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-91
TOOLS - 2.4L ENGINE, SPECIAL ..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL .......9-98
TOOLS - 41TE AUTOMATIC TRANSAXLE, SPECIAL .......................... 21-213
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10
TOOLS - BATTERY SYSTEM SPECIAL TOOLS, SPECIAL ...................... 8F-7
TOOLS - BODY, SPECIAL ...............23-13
TOOLS - COOLING SYSTEM, SPECIAL ......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL .....11-4
TOOLS - FRONT SUSPENSION, SPECIAL ....2-3
TOOLS - FUEL, SPECIAL ...........14-27,14-4
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-7
TOOLS - POWER DISTRIBUTION SYSTEMS, SPECIAL ................8W -97-1
TOOLS - POWER STEERING GEAR, SPECIAL ........................... 19-34
TOOLS - POWER STEERING PUMP, SPECIAL ........................... 19-44
TOOLS - POWER STEERING, SPECIAL .....19-9
TOOLS - REAR SUSPENSION, SPECIAL ....2-28
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, SCHEMATICS AND DIAGRAMS - SPECIAL ........................... 21-68
TOOLS, SPECIAL TOOLS - BATTERY SYSTEM SPECIAL ..................... 8F-7
TOOLS, SPECIFICATIONS - SPECIAL ......8F-24
TOP COVER - INSTALLATION, INSTRUMENT PANEL .................. 23-72
TOP COVER - REMOVAL, INSTRUMENT PANEL ............................. 23-72
TOP PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL .................. 23-77
TOP PAD ASSEMBLY - REMOVAL, INSTRUMENT PANEL .................. 23-77
TORQUES, SPECIFICATIONS ............8F-36
TOUCH-UP - DESCRIPTION, PAINTED ....23-101
TOWING - STANDARD PROCEDURE .......0-26
TPM - CAUTION, SENSOR ..............22-11
TPM - DESCRIPTION, SENSOR ..........22-10
TPM - INSTALLATION, SENSOR .........22-11
TPM - OPERATION, SENSOR ............22-10
TPM - REMOVAL, SENSOR .............22-11
TRACK - DESCRIPTION, POWER SEAT ....8N-37
TRACK - INSTALLATION, BENCH SEAT . . . 23-148
TRACK - OPERATION, POWER SEAT .....8N-38
TRACK & RACK - DESCRIPTION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - INSTALLATION, LOWER DRIVE UNIT .................. 8N-58
TRACK & RACK - OPERATION, LOWER DRIVE UNIT ........................ 8N-57
TRACK & RACK - REMOVAL, LOWER DRIVE UNIT ........................ 8N-57
TRACK - REAR COVER - INSTALLATION, FRONT SEAT ....................... 23-128
TRACK - REAR COVER - REMOVAL, FRONT SEAT ....................... 23-128
TRACK - REMOVAL, BENCH SEAT .......23-148
TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT SEAT ..........23-128
TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT SEAT ..............23-126
TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT SEAT ..........23-125
TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT SEAT ..............23-124
TRACK BAR - DESCRIPTION .............2-45
TRACK BAR - INSTALLATION ............2-46
TRACK BAR - OPERATION ...............2-46
TRACK BAR - REMOVAL ................2-46
TRACK, DIAGNOSIS AND TESTING - POWER SEAT ....................... 8N-38
TRACK MANUAL ADJUSTER - INSTALLATION, FRONT SEAT ..........23-126TRACK MANUAL ADJUSTER - REMOVAL,
FRONT SEAT ....................... 23-125
TRACK POWER ADJUSTER - INSTALLATION, FRONT SEAT ..........23-124
TRACK POWER ADJUSTER - REMOVAL, FRONT SEAT ....................... 23-124
TRACK REAR COVER - OCS - INSTALLATION, FRONT SEAT ..........23-129
TRACK REAR COVER - OCS - REMOVAL, FRONT SEAT ....................... 23-129
TRACTION CONTROL SWITCH - DIAGNOSIS AND TESTING ..............5-94
TRACTION CONTROL SWITCH - INSTALLATION ........................ 5-95
TRACTION CONTROL SWITCH - REMOVAL ........................... 5-95
TRACTION CONTROL SYSTEM - DESCRIPTION ........................ 5-88
TRACTION CONTROL SYSTEM - OPERATION .......................... 5-89
TRANSAXLE - DESCRIPTION, 40TE AUTOMATIC .......................... 21-2
TRANSAXLE - DESCRIPTION, 41TE AUTOMATIC ........................ 21-147
TRANSAXLE - OPERATION, 40TE AUTOMATIC .......................... 21-4
TRANSAXLE - OPERATION, 41TE AUTOMATIC ........................ 21-149
TRANSAXLE - SPECIFICATIONS, 41TE . . . 21-211, 21-66
TRANSAXLE FLUID - DESCRIPTION, AUTOMATIC/MANUAL ...................0-4
TRANSAXLE GENERAL DIAGNOSIS - DIAGNOSIS AND TESTING, 4XTE .....21-149,21-5
TRANSAXLE HYDRAULIC SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE . . . 21-199, 21-54
TRANSAXLE, SPECIAL TOOLS - 41TE AUTOMATIC ........................ 21-213
TRANSDUCER - DESCRIPTION, A/C PRESSURE ......................... 24-20
TRANSDUCER - OPERATION, A/C PRESSURE ......................... 24-20
TRANSDUCER, DIAGNOSIS AND TESTING - A/C PRESSURE .............24-21
TRANSFER UNIT FLUID - DESCRIPTION, AWD POWER ..........................0-6
TRANSMISSION CONTROL RELAY - DESCRIPTION ................ 21-130,21-281
TRANSMISSION CONTROL RELAY - OPERATION .................. 21-130,21-281
TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/
ASSEMBLY - STANDARD PROCEDURE .....7-38
TRANSMISSION OIL COOLER - DESCRIPTION ........................ 7-39
TRANSMISSION OIL COOLER - INSPECTION ......................... 7-39
TRANSMISSION OIL COOLER LINES - INSTALLATION ........................ 7-40
TRANSMISSION OIL COOLER LINES - REMOVAL ........................... 7-39
TRANSMISSION RANGE SENSOR - DESCRIPTION ................ 21-130,21-281
TRANSMISSION RANGE SENSOR - INSTALLATION ................ 21-131,21-282
TRANSMISSION RANGE SENSOR - OPERATION .................. 21-131,21-282
TRANSMISSION RANGE SENSOR - REMOVAL ................... 21-131,21-282
TRANSMITTER - DESCRIPTION, UNIVERSAL ........................ 8M-11
TRANSMITTER CODES, STANDARD PROCEDURE - ERASING ..............8M-12
TRANSMITTER CODES, STANDARD PROCEDURE - SETTING ...............8M-12
TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS ENTRY ............8N-24
TRANSMITTER, DIAGNOSIS AND TESTING - UNIVERSAL ...............8M-11
TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ENTRY ..................... 8N-24
TRANSMITTER RANGE - SPECIFICATIONS ..................... 8N-24
TRANSPONDER KEY - DESCRIPTION ......8Q-6
TRANSPONDER KEY - OPERATION ........8Q-6TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE ...............8Q-6
TRANSVERSE BRACKET - DESCRIPTION . . 8N-19
TRANSVERSE BRACKET - INSTALLATION . . 8N-19
TRANSVERSE BRACKET - OPERATION ....8N-19
TRANSVERSE BRACKET - REMOVAL .....8N-19
TRAY - DESCRIPTION, BATTERY .........8F-19
TRAY - INSTALLATION, BATTERY ........8F-20
TRAY - INSTALLATION, FLOOR CONSOLE BASE .............................. 23-89
TRAY - REMOVAL, BATTERY ............8F-19
TRAY - REMOVAL, FLOOR CONSOLE BASE .............................. 23-89
TREAD WEAR INDICATORS - DIAGNOSIS AND TESTING ....................... 22-16
TRIM - INSTALLATION, A-PILLAR ........23-79
TRIM - INSTALLATION, A-PILLAR LOWER EXTENSION .................. 23-79
TRIM - INSTALLATION, B-PILLAR LOWER ............................ 23-80
TRIM - INSTALLATION, B-PILLAR UPPER . . 23-80
TRIM - INSTALLATION, COWL ..........23-88
TRIM - INSTALLATION, C-PILLAR ........23-88
TRIM - INSTALLATION, REAR HEADER ....23-96
TRIM - REMOVAL, A-PILLAR ...........23-79
TRIM - REMOVAL, A-PILLAR LOWER EXTENSION ......................... 23-79
TRIM - REMOVAL, B-PILLAR LOWER .....23-79
TRIM - REMOVAL, B-PILLAR UPPER .......23-80
TRIM - REMOVAL, COWL ..............23-88
TRIM - REMOVAL, C-PILLAR ...........23-88
TRIM - REMOVAL, REAR HEADER .......23-96
TRIM BOLSTER - INSTALLATION, QUARTER .......................... 23-95
TRIM BOLSTER - REMOVAL, QUARTER . . . 23-95
TRIM CARE, CLEANING - WHEEL AND WHEEL ............................ 22-19
TRIM PANEL - INSTALLATION .....23-20,23-34,
23-43
TRIM PANEL - INSTALLATION, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - INSTALLATION, LEFT QUARTER .......................... 23-94
TRIM PANEL - INSTALLATION, RIGHT D-PILLAR ........................... 23-98
TRIM PANEL - INSTALLATION, RIGHT QUARTER .......................... 23-97
TRIM PANEL - REMOVAL ....23-20,23-34,23-43
TRIM PANEL - REMOVAL, LEFT D-PILLAR ........................... 23-94
TRIM PANEL - REMOVAL, LEFT QUARTER .......................... 23-94
TRIM PANEL - REMOVAL, RIGHT D-PILLAR ........................... 23-97
TRIM PANEL - REMOVAL, RIGHT QUARTER .......................... 23-97
TRIM PLATE - INSTALLATION, DOOR SILL ............................... 23-89
TRIM PLATE - REMOVAL, DOOR SILL ....23-89
TRIM RING AND COVER - FOLD-IN- FLOOR - INSTALLATION, CARPET ........23-84
TRIM RING AND COVER - FOLD-IN- FLOOR - REMOVAL, CARPET ...........23-84
TRIP DEFINITION, DESCRIPTION .........25-1
TROUBLE CODES - STANDARD PROCEDURE, OBTAINING DIAGNOSTIC . . . 8E-15
TUB CARPET INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR ....23-98
TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR ........23-98
TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR ..........23-96
TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR .............23-95
TUBE - 2.4L - DESCRIPTION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - INSTALLATION, WATER PUMP INLET ......................... 7-36
TUBE - 2.4L - REMOVAL, WATER PUMP INLET ............................... 7-36
TUBE - 3.3/3.8L - INSTALLATION, WATER PUMP INLET ......................... 7-37
TUBE - 3.3/3.8L - REMOVAL, WATER PUMP INLET ......................... 7-37
TUBE - INSTALLATION, DRAIN .........23-172
TUBE - INSTALLATION, EXHAUST .......24-116
TUBE - INSTALLATION, FUEL TANK FILLER ............................. 14-17
RS INDEX33
Description Group-Page Description Group-Page Description Group-Page