2005 CHRYSLER SEBRING SEDAN garage door opener

▫Multi-Function Control Lever..............66
▫Headlights, Parking Lights, Instrument Panel
Lights..............................66
▫Automatic Headlights—If Equipped.........67
▫Daytime Running Lights (Canada Only)......67
▫Lights-On Reminder....................67
▫Fog Lights—If Equipped................67
▫Turn Signals..........................67
▫Headlight Beam Select Switch.............68
▫Flash To Pass.........................68
▫Headlight Time Delay...................68

Windshield Wipers And Washers...........68
▫Mist................................69
▫Speed Sensitive Intermittent Wiper System....69

Tilt Steering Column.....................70

Traction Control—If Equipped.............71

Electronic Speed Control—If Equipped......71
▫To Activate...........................72
▫To Set At A Desired Speed................72
▫To Deactivate.........................72
▫To Resume Speed......................72
▫To Vary The Speed Setting................72
▫To Accelerate For Passing................73
▫Using Speed Control On Hills.............73

Garage Door Opener—If Equipped.........74
▫Programming The Universal Transceiver......75
▫“Rolling Code”Programming.............76
▫Canadian Programming/Gate Programming . . .78
▫Operation............................78
▫Reprogramming A Single Button...........78
▫Security.............................78
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rolling Hills
The transaxle may downshift into third gear and remain
there as the vehicle travels over rolling hills. The trans-
axle will upshift into fourth gear when the road flattens
out.
The transaxle will resume its normal shift schedule if you
depress the accelerator pedal during any of the above
conditions.
WARNING!
Speed Control can be dangerous where the system
can’t maintain a constant speed. Your vehicle could
go too fast for the conditions, and you could lose
control. An accident could be the result. Don’t use
Speed Control in heavy traffic or on roads that are
winding, icy, snow-covered, or slippery.
GARAGE DOOR OPENER—IF EQUIPPED
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. It triggers these devices at the
push of a button. The Universal Transceiver operates off
your vehicle’s battery and charging system; no batteries
are needed.
For additional information on HomeLink, call 1–800–
355–3515, or on the internet at www.homelink.com.
Homelink Buttons
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
A moving garage door can cause injury to people and
pets in the path of the door. People or pets could be
seriously or fatally injured. Only use this transceiver
with a garage door opener that has a“stop and
reverse”feature as required by federal safety stan-
dards. This includes most garage door opener mod-
els manufactured after 1982. Do not use a garage
door opener without these safety features it could
cause injury or death. Call toll-free 1–800–355–3515
or, on the Internet at www.homelink.com for safety
information or assistance.
Programming The Universal Transceiver
For best results, install a new battery in the hand held
transmitter before programming. If your garage door
opener (located in the garage) is equipped with an
antenna, make sure that the antenna is hanging straight
down.
1. Turn off the engine.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle’s exhaust while
training the transceiver. Exhaust gas can cause seri-
ous injury or death.
WARNING!
Your motorized door or gate will open and close
while you are training the Universal Transceiver. Do
not train the transceiver if people or pets are in the
path of the door or gate. A moving door or gate can
cause serious injury or death to people and pets or
damage to objects.
2. Erase the factory test codes by pressing the two
outside buttons. Release the buttons when the light in the
Universal Transceiver begins to flash (about 20 seconds).
NOTE:Step 2 does not have to be followed to program
additional hand held transmitters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75
3

3. Choose one of the three Universal Transceiver buttons
to program. Place the hand held controller one to three
inches from the Universal Transceiver while keeping its
indicator light in view.
4. Using both hands, press the hand held transmitter
button and the desired Universal Transceiver button. Do
not release the buttons until step 5 has been completed.
NOTE:Some entry gates and garage door openers may
require you to replace step 4 with the procedures listed
under Canadian Programming.5. The indicator light in the Universal Transceiver will
begin to flash, first slowly and then rapidly. The rapid
flashing indicates successful programming. If after 90
seconds the indicator light does not flash rapidly or goes
out, return to step 1 and repeat the procedure. To train the
other buttons, repeat steps 3 and 4. Be sure to keep your
hand held transmitters in case you need to retrain the
Universal Transceiver.
NOTE:If you do not successfully program the
Universal Transceiver to learn the signal of your hand
held transmitter, refer to the Rolling Code Paragraph, or
call toll free for customer assistance at 1–800–355–3515,
or on the internet at www.homelink.com.
“Rolling Code”Programming
NOTE:
If your hand held transmitter appears to pro-
gram the Universal Transceiver, but your garage door or
other device does not operate, and your device was
manufactured after 1996, your garage door opener or
other device may have a“Rolling Code”system.Programming Universal Transceiver
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

On garage door openers with the“Rolling Code”feature,
the transmitter code changes after each use to prevent the
copying of your code.
To check if your device is protected by a“Rolling Code”
system:
•Check the owner’s manual for the device for mention
of“Rolling Codes”.
•Press and hold the programmed button on the Univer-
sal Transceiver. If the Universal Transceiver indicator
light flashes rapidly and then stays on after 2 seconds,
the device has the“Rolling Code”feature.
To train a garage door opener (or other rolling code
equipped devices) with the rolling code feature, follow
these instructionsaftercompleting theProgramming
portion of this text:
NOTE:The assistance of a second person may make the
following programming procedure quicker and easier.
1. Locate the training button on the garage door motor
head unit. The exact location and color of the button may
vary by garage door opener manufacturer. If you havedifficulty in locating the training button, check your
garage door opener manual, or call 1-800-355-3515 or, on
the Internet, at www.homelink.com.
2. Press and hold the training button on the garage door
opener head unit. This will activate the“training”light.
NOTE:After completing step 2, you have 30 seconds to
start step 3.
3. Return to the Universal Transceiver in the vehicle and
firmly press and release the garage door button. Press
and release the button a second time to complete the
training process. Some garage door openers may require
you to do this procedure a third time to complete the
training.
Your garage door opener should now recognize your
Universal Transceiver. The remaining two buttons may
now be programmed if this has not previously been
done. Refer to the Programming instructions. You may
use either your Universal Transceiver or your original
hand-held transmitter to open you garage door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77
3

Canadian Programming/Gate Programming
Canadian frequency laws, and the technology of some
entry gates, require you to press and release the hand
held transmitter button every two seconds during pro-
gramming
Continue to press and hold the Universal Transceiver
button while you press and release the hand held trans-
mitter button until the frequency signal has been learned.
The Universal Transceiver light will flash slowly and
then rapidly when the programming is successful.
NOTE:When programming such a garage door opener
or gate, unplug the device to prevent possible damage to
the garage door or gate motor.
Operation
Press and hold the desired button on the Universal
Transceiver until the garage door or other device begins
to operate. The light in the display shows that the signal
is being transmitted. The hand held transmitter may also
be used at any time.
Reprogramming A Single Button
1. Press and hold the Universal Transceiver button to be
reprogrammed. Do not release until step 4 has been
completed.
2. When the indicator light begins to flash slowly (after
20 seconds) position the hand held transmitter one to
three inches away from the button to be trained.
3. Press and hold the hand held transmitter button.
4. The Universal Transceiver indicator light will begin to
flash, first slowly, then rapidly. When the indicator lights
begin to flash rapidly, release both buttons.
Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously trained frequencies, hold
down both outside buttons until the green light begins to
flash.
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Daytime Brightness, Interior Lights.......... 65
Daytime Running Lights.................. 67
Dealer Service......................... 205
Defroster, Rear Window.................. 136
Defroster, Windshield...............49,130,135
Diagnostic System, Onboard............... 203
Dimmer Control........................ 64
Dimmer Switch, Headlight................. 68
Dipsticks
Automatic Transaxle................... 228
Disposal
Antifreeze (Engine Coolant)............. 223
Engine Oil.......................... 210
Door Ajar Warning...................... 17
Door Locks............................ 15
Door Locks, Automatic................... 17
Door Opener, Garage..................... 74
Drive Belts............................ 210
Driving
On Slippery Surfaces.................. 195
Electrical Outlet, Auxiliary................. 81
Electrical Power Outlets................... 81Electronic Speed Control.................. 71
Emergency, In Case of
Freeing Vehicle When Stuck............. 196
Jacking............................. 187
Jump Starting........................ 192
Overheating......................... 186
Towing............................. 196
Emergency Trunk Release...............24,25
Emission Control System Maintenance....204,246
Engine............................201,202
Air Cleaner Filter..................... 211
Block Heater......................... 146
Break-In Recommendations............... 48
Checking Oil Level.................... 206
Compartment.....................201,202
Coolant (Antifreeze)................220,244
Cooling............................ 220
Exhaust Gas Caution.................. 177
Fails to Start......................... 146
Fuel Requirements.................174,243
Oil ..........................206,243,244
Oil Change Interval................... 207
Oil Selection......................208,243
INDEX 281
10

Clean Air........................... 175
Ethanol............................. 182
Filler Cap........................... 178
Filter.............................. 211
Gasoline............................ 174
Gauge.............................. 90
Hoses.............................. 227
Light............................... 95
Octane Rating........................ 244
Requirements.....................174,243
Tank Capacity........................ 243
Fueling.............................. 178
Fuses................................ 234
Garage Door Opener..................... 74
GasCap .............................. 178
Gasoline............................. 174
Gasoline, Clean Air..................... 175
Gasoline, Reformulated.................. 175
Gasoline/Oxygenate Blends............... 175
Gauges
Coolant Temperature................... 92
Fuel................................ 90Speedometer......................... 91
Tachometer.......................... 91
Gearshift............................. 149
General Information...................14,21
Glass Cleaning......................... 232
Hazard Warning Flasher.................. 186
Head Restraints......................... 61
Headlights............................ 237
Aiming............................. 243
Automatic........................... 67
Bulb Replacement..................... 237
Cleaning............................ 232
High Beam.........................68,91
High Beam/Low Beam Select Switch....... 68
Passing............................. 68
Switch.............................. 66
Time Delay........................67,68
Heated Seats........................... 61
Heater............................126,133
Heater, Engine Block.................... 146
Homelink Transmitter.................... 74
Hood Latch Maintenance................. 216
INDEX 283
10