2005 CHRYSLER CROSSFIRE SRT garage door opener

To Open And Close The Hood.............71

Interior Lights.........................72
▫Front Map/Reading Lights...............73
▫Battery Saver Feature...................73
▫Instrument Panel Lighting................73
▫Night Security Illumination...............73

Exterior Lights.........................74
▫Headlights And Parking Lights............74
▫Daytime Running Lights (Where Applicable) . . .74
▫Fog Lights...........................74
▫Standing Lights.......................75

Multifunction Control Lever...............75
▫Turn Signals..........................75
▫Headlight Dimmer Switch................76
▫Passing Light.........................77
▫Windshield Wipers And Washer............77▫Mist Function.........................78

Telescoping Steering Column..............79

Tire Pressure Monitor System..............80

Brake Assist System (BAS)................82

Electronic Stability Program (ESP)...........83
▫Synchronizing ESP.....................85

Electronic Speed Control..................86
▫To Vary The Speed Setting................87
▫To Deactivate.........................88
▫To Resume Speed......................88
▫Using Speed Control On Hills.............89

Garage Door Opener....................89
▫Programming The Universal Transceiver......90
▫Gate Operator/Canadian Programming......92
▫Using The Universal Transceiver...........93
▫Erasing Universal Transceiver Buttons........93
50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Using Speed Control On Hills
Your vehicle is equipped with interactive speed control.
This feature activates when driving up or down hills with
the speed control engaged and the driver’s foot off the
accelerator.
WARNING!
Speed control can be dangerous where the system
can’t maintain a constant speed. Your vehicle could
go too fast for the conditions, and you could lose
control. An accident could be the result. Don’t use
speed control in heavy traffic or on roads that are
winding, icy, snow-covered, or slippery.
On a downgrade or an upgrade, downshifting will occur
automatically to allow the engine’s braking power to
maintain the set speed. When more level roadway is
reached, the transmission will automatically upshift to
fifth gear.
NOTE:On very steep hills, a greater speed loss or gain
may occur. It may be preferable to drive without speed
control.
GARAGE DOOR OPENER
The HomeLinkUniversal Transceiver replaces up to
three remote controls (hand-held transmitters) that oper-
ate devices such as garage door openers, motorized
gates, or home lighting. The transceiver triggers these
devices at the push of a button. The transceiver operates
off your vehicle’s battery and charging system: no bat-
teries are needed.
For additional information on HomeLink, call 1–800–
355–3515, or on the internet at www.homelink.com.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89
3

WARNING!
A moving garage door can cause injury to people and
pets in the path of the door. People or pets could be
seriously or fatally injured. Only use this transceiver
with a garage door opener that has a“stop and
reverse”feature, as required by federal safety stan-
dards. This includes most garage door opener mod-
els manufactured after 1982. Do not use a garage
door opener without these safety features, as it could
cause injury or death. Call toll-free 1–800–355–3515
or, on the internet at www.homelink.com for safety
information and assistance.
Programming The Universal Transceiver
For best results, install a new battery in the hand-held
transmitter before programming. If your garage door
opener (located in the garage) is equipped with an
antenna, make sure that the antenna is hanging straight
down.
1. Turn off the engine.
WARNING!
Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run the vehicle’s engine while
programming the transceiver. Exhaust gas can cause
serious injury or death.
WARNING!
Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people or
pets are in the path of the door or gate. A moving
door or gate can cause serious injury or death to
people and pets or damage to objects.
2. Turn the ignition to the ON/RUN position.
3. Erase the factory test codes by pressing the two
outside buttons. Release the buttons when the light in the
overhead console display begins to flash (about 20 sec-
onds).
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:Step 3 does not have to be followed to program
additional hand-held transmitters.
4. Choose one of the three buttons to program. Place the
hand-held controller 1–3 inches (25–76 mm) from the
universal transceiver while keeping its indicator light in
view.
5. Using both hands, press the hand-held transmitter
button and the desired universal transceiver button. Do
not release the buttons until Step 6 has been completed.NOTE:Some gate operators and garage door openers
may require you to replace this Programming Step 5 with
procedures noted in the“Gate Operator/Canadian Pro-
gramming”section.
6. The indicator light in the universal transceiver will
begin to flash, first slowly and then rapidly. Release both
buttons after the indicator light changes from slow to
rapid flash. If, after 90 seconds, the indicator does not
flash rapidly or goes out, return to Step 1 and repeat the
procedure.
7. Press and hold the just programmed universal trans-
ceiver button and observe the indicator light. If the
indicator stays on constantly, programming is complete
and your device should activate when the universal
transceiver button is pressed and released.
NOTE:To program the remaining two universal trans-
ceiver buttons, begin with Programming Step 4. Do not
repeat Steps 1, 2, and 3.
If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91
3

Programming Steps 8-10 to complete programming of
a rolling code equipped device (most commonly a
garage door opener).
8. At the garage door opener receiver (motor-head unit)
in the garage, locate the“learn”or“smart”button. This
can usually be found where the hanging antenna wire is
attached to the motor-head unit.
9. Firmly press and release the“learn”or“smart”but-
ton. (The name and color of the button may vary by
manufacturer.)
NOTE:There are 30 seconds in which to initiate Step 10.
10. Return to the vehicle and firmly press, hold for two
seconds and release the programmed universal trans-
ceiver button. Repeat the“press/hold/release”sequence
a second time, and, depending on the brand of the garage
door opener (or other rolling code equipped device),
repeat this sequence a third time to complete the pro-
gramming.
The universal transceiver should now activate your roll-
ing code equipped device.If you do not successfully program the universal trans-
ceiver to learn the signal of your hand-held transmitter,
call toll free for customer assistance at 1-800-355-3515, or
on the internet at www.homelink.com.
Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to“time-out”(or quit) after several seconds of
transmission. This may not be long enough for the
universal transceiver to pick up the signal during pro-
gramming. Similar to this Canadian law, some U.S. gate
operators are designed to“time-out”in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the programming
procedures (regardless of where you live), replace Pro-
gramming Step 5 with the following:
NOTE:If programming a garage door opener or gate
operator, it is advised to unplug the device during the
“cycling”process to prevent possible overheating.
5. Continue to press and hold the universal transceiver
button while you press and release every two seconds
(“cycle”) your hand-held transmitter until the frequency
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

signal has successfully been accepted by the universal
transmitter. (The indicator light will flash slowly and
then rapidly.) Proceed with Programming Step 6 to
complete.
Using the Universal Transceiver
To operate the universal transceiver, simply press and
release the programmed button. Activation will now
occur for the programmed device (i.e. garage door opener,
gate operator, security system, entry door lock, home/
office lighting, etc.) For convenience, the hand-held trans-
mitter of the device may also be used at any time.
Erasing Universal Transceiver Buttons
To erase programming from the three buttons (individual
buttons cannot be erased but can be reprogrammed–see
below), follow this procedure:
•Press and hold the two outer universal transceiver
buttons until the indicator light begins to flash after 20
seconds. Release both buttons. Do not hold for longer
than 30 seconds. The universal transceiver is now in
the program (or learning) mode and can be pro-
grammed at any time beginning with Programming
Step 4.
Reprogramming a Single Button
To program a device using a universal transceiver button
previously programmed, follow these steps:
1. Press and hold the desired universal transceiver but-
ton. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds.
Without releasing the universal transceiver button, pro-
ceed with Programming Step 4.
Security
If you sell your vehicle, be sure to erase the frequencies.
To erase all of the previously programmed frequencies,
hold down both outside buttons until the light begins to
flash.
This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received, including interference that may cause undes-
ired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
3

Garage Door Opener..................... 89
GasCap .............................. 160
Gasoline............................. 235
Gasoline/Oxygenate Blends............... 158
Gear Ratios........................... 233
Glass Cleaning......................... 218
Glove Compartment..................... 65
Hazard Warning Flasher.................. 166
Headlights
Aiming............................. 231
Cleaning............................ 218
Dimmer Switch....................... 76
Heater............................... 120
Hood Latch Maintenance................. 204
Hood Release.......................... 71
Hoses................................ 211
Ignition
Key ................................. 9
Wiring System....................... 201
Illuminated Entry....................... 73
Infant Restraint......................... 40Inside Rearview Mirror................... 66
Instrument Cluster....................... 97
Instrument Panel and Controls.............. 96
Instrument Panel Cover.................. 218
Instrument Panel Lens Cleaning............ 219
Interior Appearance Care................. 217
Introduction............................ 4
Jack Location.......................... 172
Jack Operation......................... 167
Jump Starting......................... 174
Key-In Reminder........................ 10
Keyless Entry System..................... 14
Keys.................................. 9
Knee Bolster........................... 29
Lap/Shoulder Belts...................... 23
Light Bulbs........................... 228
Lights
Airbag...........................32,107
Anti-Lock Warning.................... 102
Back-Up............................ 230
INDEX 269
10