2005 CHRYSLER CARAVAN battery replacement

REMOVAL
(1) Disconnect and isolate the negative battery
cable.
(2) Remove the cover from the integrated power
module (IPM) (Fig. 8).
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the IPM for A/C compressor
clutch relay identification and location.
(3) Remove the A/C compressor clutch relay from
the IPM.
INSTALLATION
NOTE: Refer to the fuse and relay map on the inner
surface of the cover of the integrated power module
(IPM) for A/C compressor clutch relay identification
and location.
(1) Position the A/C compressor clutch relay into
the proper receptacle in the IPM.
(2) Align the A/C compressor clutch relay termi-
nals with the terminal cavities in the IPM receptacle.
(3) Push down firmly on the A/C compressor clutch
relay until the terminals are fully seated in the ter-
minal cavities.
(4) Install the cover onto the IPM.
(5) Reconnect the negative battery cable.
A/C HEATER CONTROL
DESCRIPTION
The A/C-heater control is located at the center of
the instrument panel and uses electrical controls.
These controls provide the vehicle operator with a
number of setting options to help control the climate
and comfort within the vehicle. Refer to the owner's
manual in the vehicle glove box for more information
on the suggested operation and use of these controls.
The A/C-heater control cannot be repaired. If faulty
or damaged, the entire unit must be replaced. The
control knobs are available for service replacement.
STANDARD PROCEDURE
A/C-HEATER CONTROL CALIBRATION
The A/C-heater control module must be recali-
brated each time an actuator motor or the control
module is replaced. If the vehicle is so equipped, the
calibration procedure also includes rear HVAC posi-
tions for each actuator motor.
(1) Turn the ignition switch to the On position.
(2) If equipped with the manual temperature con-
trol (MTC) system, press and hold the Rear Wipe/
Wash and Recirculation buttoms for at least five
seconds. If equipped with the automatic temperature
control (ATC) systen, simultaneously press and hold
the Power and Recirculation buttons on the A/C-
heater control for at least five seconds. The MTC
A/C-heater control Rear Wipe/Wash Light Emitting
Diode (LED) and Recirculation LED, or the ATC A/C-
heater control Delay and Recirculation graphics will
begin to flash when the calibration procedure has
begun.
(3) The calibration procedure should take less than
two minutes to complete for the manual A/C-heater
control, and less than twenty seconds for the ATC
A/C-heater control. When the LEDs or graphics stop
flashing, the calibration procedure is complete.
(4) If the LEDs or graphics continue to flash
beyond the two minute (manual) or twenty second
(ATC) calibration time, it indicates that the A/C-
heater control has detected a failure and a Diagnostic
Trouble Code (DTC) has been set. Refer to Body
Diagnostic Procedures to perform further diagnosis.
The LEDs or graphics will continue to flash even
after the ignition switch is cycled Off and On, until a
successful calibration is completed or until the vehi-
cle has been driven about 13 kilometers (8 miles).
Fig. 8 A/C Compressor Clutch Relay
1 - INTEGRATED POWER MODULE (IPM)
2 - A/C COMPRESSOR CLUTCH RELAY
3 - FRONT CONTROL MODULE
RSCONTROLS - FRONT24-19
A/C COMPRESSOR CLUTCH RELAY (Continued)

BACKLIGHT (EBL) SYSTEM, DIAGNOSISAND TESTING - ELECTRIC ..............8G-2
BACKSTOW STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-158
BACKSTOW STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-158
BAG RETAINER - INSTALLATION, PLASTIC GROCERY .................. 23-149
BAG RETAINER - REMOVAL, PLASTIC GROCERY ......................... 23-149
BALANCE - STANDARD PROCEDURE, TIRE AND WHEEL ..................... 22-5
BALANCE SHAFTS AND CARRIER ASSEMBLY - DESCRIPTION .............9-71
BALANCE SHAFTS AND CARRIER ASSEMBLY - INSTALLATION .............9-73
BALANCE SHAFTS AND CARRIER ASSEMBLY - OPERATION ...............9-71
BALANCE SHAFTS AND CARRIER ASSEMBLY - REMOVAL .................9-71
BALL JOINT - DESCRIPTION, LOWER ......2-10
BALL JOINT - DIAGNOSIS AND TESTING, LOWER ............................. 2-10
BALL JOINT - OPERATION, LOWER .......2-10
BAR - DESCRIPTION, STABILIZER ....2-16,2-44
BAR - DESCRIPTION, TRACK ............2-45
BAR - INSPECTION, STABILIZER ..........2-17
BAR - INSTALLATION, STABILIZER ........2-17
BAR - INSTALLATION, TRACK ............2-46
BAR - OPERATION, STABILIZER ......2-16,2-44
BAR - OPERATION, TRACK ................2-46
BAR - REMOVAL, STABILIZER ...........2-17
BAR - REMOVAL, TRACK ...............2-46
BAR CUSHION - INSTALLATION, STABILIZER ...........................2-4
BAR CUSHION - REMOVAL, STABILIZER ....2-4
BASE BRAKE BLEEDING - STANDARD PROCEDURE ..........................5-8
BASE BRAKE SYSTEM - DIAGNOSIS AND TESTING .............................5-4
BASE BRAKE SYSTEM, SPECIAL TOOLS ....5-10
BASE BRAKES - DESCRIPTION ............5-3
BASE BRAKES - OPERATION ..............5-3
BASE BRAKES (EXPORT) - DESCRIPTION . . . 5-3
BASE COAT/CLEARCOAT FINISH - DESCRIPTION ...................... 23-101
BASE RISER - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-135
BASE RISER - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-134
BASE TRAY - INSTALLATION, FLOOR CONSOLE ........................... 23-89
BASE TRAY - REMOVAL, FLOOR CONSOLE ........................... 23-89
BATTERY - DESCRIPTION ...............8F-7
BATTERY - OPERATION .................8F-9
BATTERY - REMOVAL .................8F-16
BATTERY - SPECIFICATIONS ............8N-24
BATTERY CABLES - DESCRIPTION .......8F-16
BATTERY CABLES - OPERATION .........8F-17
BATTERY CABLES, DIAGNOSIS AND TESTING ........................... 8F-17
BATTERY CHARGING, STANDARD PROCEDURE - CONVENTIONAL ..........8F-11
BATTERY CHARGING, STANDARD PROCEDURE - SPIRAL PLATE ...........8F-10
BATTERY, DIAGNOSIS AND TESTING ......8F-9
BATTERY ELECTROLYTE LEVEL, STANDARD PROCEDURE - CHECKING ....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-16
BATTERY HOLDDOWN - REMOVAL .......8F-16
BATTERY REPLACEMENT - STANDARD PROCEDURE ........................ 8N-24
BATTERY, SPECIFICATIONS ..............8F-6
BATTERY SYSTEM - DESCRIPTION ........8F-1
BATTERY SYSTEM - OPERATION .........8F-2
BATTERY SYSTEM, DIAGNOSIS AND TESTING ............................ 8F-2
BATTERY SYSTEM SPECIAL TOOLS, SPECIAL TOOLS ...................... 8F-7
BATTERY TEMPERATURE SENSOR - DESCRIPTION ....................... 8F-24
BATTERY TEMPERATURE SENSOR - OPERATION ......................... 8F-24
BATTERY TEMPERATURE SENSOR - REMOVAL .......................... 8F-24
BATTERY TEMPERATURE SENSOR - SPECIFICATIONS ..................... 8F-23BATTERY TESTER, STANDARD
PROCEDURE - MICRO 420 .............8F-15
BATTERY TRAY - DESCRIPTION .........8F-19
BATTERY TRAY - INSTALLATION .........8F-20
BATTERY TRAY - REMOVAL ............8F-19
BEARING - DESCRIPTION, HUB .......2-30,2-5
BEARING - DIAGNOSIS AND TESTING, HUB............................. 2-31,2-5
BEARING - INSTALLATION, HUB .......2-33,2-5
BEARING - OPERATION, HUB .........2-30,2-5
BEARING - REMOVAL, HUB ..........2-31,2-5
BEARING CLEARANCE - STANDARD PROCEDURE, MEASURING
CONNECTING ROD ................... 9-123
BEARING CLEARANCE USING PLASTIGAGE - STANDARD
PROCEDURE, MEASURING ..........9-12,9-86
BEARING FITTING - STANDARD PROCEDURE, MAIN ................... 9-125
BEARING PRELOAD - ADJUSTMENT, DIFFERENTIAL ...................... 21-228
BEARING PRELOAD MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL ....................... 21-79
BEARINGS - INSTALLATION, CRANKSHAFT MAIN .................. 9-127
BEARINGS - REMOVAL, CRANKSHAFT MAIN .............................. 9-127
BEARINGS (IN BLOCK) - DESCRIPTION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - INSPECTION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - INSTALLATION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - OPERATION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - REMOVAL, CAMSHAFT ......................... 9-118
BELLCRANK - INSTALLATION ...........23-35
BELLCRANK - REMOVAL ...............23-35
BELT - DIAGNOSIS AND TESTING, ACCESSORY DRIVE .....................7-7
BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER LAP ..............23-157
BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER LAP ..............23-157
BELT - INSTALLATION, TIMING ...........9-67
BELT - REMOVAL, TIMING ..............9-65
BELT & RETRACTOR - FIRST ROW - OUTBOARD - INSTALLATION, SEAT ......8O-40
BELT & RETRACTOR - FIRST ROW - OUTBOARD - REMOVAL, SEAT ..........8O-39
BELT & RETRACTOR - OUTBOARD - FRONT - INSTALLATION, SEAT ..........8O-39
BELT & RETRACTOR - OUTBOARD - FRONT - REMOVAL, SEAT ..............8O-38
BELT & RETRACTOR - SECOND ROW - LEFT OUTBOARD - INSTALLATION,
SEAT .............................. 8O-42
BELT & RETRACTOR - SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT .....8O-42
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD - INSTALLATION,
SEAT .............................. 8O-40
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT ....8O-40
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC -
LWB - INSTALLATION, SEAT ............8O-41
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC -
LWB - REMOVAL, SEAT ...............8O-41
BELT BUCKLE - FIRST ROW - BENCH - INSTALLATION, SEAT .................8O-37
BELT BUCKLE - FIRST ROW - BENCH - REMOVAL, SEAT ..................... 8O-36
BELT BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT ....8O-36
BELT BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT .......8O-35
BELT BUCKLE - FRONT INBOARD - INSTALLATION, SEAT .................8O-35
BELT BUCKLE - FRONT INBOARD - REMOVAL, SEAT ..................... 8O-35
BELT BUCKLE - SECOND ROW - THREE PASSENGER BENCH - INSTALLATION,
SEAT .............................. 8O-40BELT BUCKLE - SECOND ROW - THREE
PASSENGER BENCH - REMOVAL, SEAT . . . 8O-40
BELT BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT . . . 8O-38
BELT BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT .......8O-37
BELT CENTER LAP BELT - FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-157
BELT CENTER LAP BELT - FOLD-IN- FLOOR - REMOVAL, SEAT .............23-157
BELT COVER(S) - INSTALLATION, TIMING ............................. 9-64
BELT COVER(S) - REMOVAL, TIMING ......9-63
BELT HEIGHT ADJUSTE R-BOR
C-PILLAR - INSTALLATION, SEAT ........8O-38
BELT HEIGHT ADJUSTE R-BOR
C-PILLAR - REMOVAL, SEAT ...........8O-38
BELT HEIGHT ADJUSTER KNOB - INSTALLATION, SEAT .................8O-38
BELT HEIGHT ADJUSTER KNOB - REMOVAL, SEAT ..................... 8O-38
BELT MOLDING - INSTALLATION, FRONT DOOR INNER ....................... 23-168
BELT MOLDING - INSTALLATION, FRONT DOOR OUTER ...................... 23-167
BELT MOLDING - REMOVAL, FRONT DOOR INNER ....................... 23-168
BELT MOLDING - REMOVAL, FRONT DOOR OUTER ...................... 23-167
BELT TENSION - STANDARD PROCEDURE, CHECKING POWER
STEERING ............................7-8
BELT TENSION SENSOR - DESCRIPTION . . . 8O-8
BELT TENSION SENSOR - OPERATION .....8O-9
BELT TENSION, SPECIFICATIONS - ACCESSORY DRIVE .....................7-5
BELT TENSIONER - 2.4L - INSTALLATION . . 7-11
BELT TENSIONER - 2.4L - REMOVAL ......7-11
BELT TENSIONER - 3.3/3.8L - INSTALLATION ........................ 7-12
BELT TENSIONER - 3.3/3.8L - REMOVAL . . . 7-12
BELT TENSIONER - DESCRIPTION, SEAT . . 8O-43
BELT TENSIONER - OPERATION, SEAT ....8O-43
BELT TENSIONER & PULLEY - INSTALLATION, TIMING .................9-70
BELT TENSIONER & PULLEY - REMOVAL, TIMING .................... 9-69
BELTS - 2.4L - ADJUSTMENTS, DRIVE .....7-10
BELTS - 2.4L - INSTALLATION, DRIVE ......7-9
BELTS - 2.4L - REMOVAL, DRIVE ..........7-9
BELTS - 3.3/3.8L - INSTALLATION, DRIVE . . 7-12
BELTS - 3.3/3.8L - REMOVAL, DRIVE ......7-11
BELTS - CLEANING, DRIVE ...............7-8
BELTS - INSPECTION, DRIVE .............7-8
BENCH - INSTALLATION, SEAT BACK HINGE COVERS - QUAD BUCKET, 50/50
SPLIT ............................. 23-146
BENCH - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW ................8O-37
BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW - THREE
PASSENGER ........................ 8O-40
BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW INBOARD -
50/50 .............................. 8O-38
BENCH - INSTALLATION, SEAT CUSHION COVER - QUAD BUCKET, 50/50 SPLIT . . . 23-144
BENCH - REMOVAL, SEAT BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT . . 23-146
BENCH - REMOVAL, SEAT BELT BUCKLE - FIRST ROW ....................... 8O-36
BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW - THREE PASSENGER ....8O-40
BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW INBOARD - 50/50 .......8O-37
BENCH - REMOVAL, SEAT CUSHION COVER - QUAD BUCKET, 50/50 SPLIT . . . 23-144
BENCH SEAT - REMOVAL, CHILD SEAT MODULE .......................... 23-104
BENCH SEAT BACK - INSTALLATION .....23-147
BENCH SEAT BACK - REMOVAL ........23-147
BENCH SEAT BACK COVER - INSTALLATION ...................... 23-148
BENCH SEAT BACK COVER - REMOVAL . . 23-148
BENCH SEAT BACK HINGE - REMOVAL . . 23-146
BENCH SEAT BACK PANEL - INSTALLATION ...................... 23-144
BENCH SEAT BACK PANEL - REMOVAL . . 23-143
RS INDEX3
Description Group-Page Description Group-Page Description Group-Page

TANK - STANDARD PROCEDURE,DRAINING FUEL ...................... 14-2
TANK FILLER TUBE - INSTALLATION, FUEL .............................. 14-17
TANK FILLER TUBE - REMOVAL, FUEL ....14-16
TAPE ATTACHED - INSTALLATION, EXTERIOR NAME PLATES ..............23-51
TAPE ATTACHED - REMOVAL, EXTERIOR NAME PLATES ....................... 23-51
TASK MANAGER - DESCRIPTION ........25-25
TASK MANAGER - OPERATION ..........25-25
TELECOMMUNICATION, DIAGNOSIS AND TESTING ............................8T-1
TEMP SENSOR - DESCRIPTION, AMBIENT .......................... 8M-12
TEMP SENSOR - OPERATION, AMBIENT . . 8M-12
TEMPERATURE CONTROL, DESCRIPTION - AUTOMATIC ........................ 24-3
TEMPERATURE CONTROL, OPERATION - AUTOMATIC .......................... 24-5
TEMPERATURE CONTROL SYSTEM, OPERATION - AUTOMATIC ............24-114
TEMPERATURE CONTROL SYSTEM, OPERATION - MANUAL ...............24-113
TEMPERATURE SENSOR - 2.4L - DESCRIPTION, ENGINE COOLANT .........7-21
TEMPERATURE SENSOR - 2.4L - INSTALLATION, ENGINE COOLANT ........7-21
TEMPERATURE SENSOR - 2.4L - REMOVAL, ENGINE COOLANT ............7-21
TEMPERATURE SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE COOLANT .........7-21
TEMPERATURE SENSOR - 3.3/3.8L - INSTALLATION, ENGINE COOLANT ........7-23
TEMPERATURE SENSOR - 3.3/3.8L - REMOVAL, ENGINE COOLANT ............7-21
TEMPERATURE SENSOR - DESCRIPTION, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - DESCRIPTION, EVAPORATOR ....................... 24-26
TEMPERATURE SENSOR - DESCRIPTION, INFRARED .......................... 24-28
TEMPERATURE SENSOR - DESCRIPTION, INLET AIR .......................... 14-34
TEMPERATURE SENSOR - OPERATION, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - OPERATION, EVAPORATOR ....................... 24-27
TEMPERATURE SENSOR - OPERATION, INFRARED .......................... 24-28
TEMPERATURE SENSOR - REMOVAL, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - SPECIFICATIONS, BATTERY .............8F-23
TEMPERATURE SENSOR CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT ....8M-12
TEMPERATURE SENSOR, DIAGNOSIS AND TESTING - AMBIENT .............8M-12
TENSION - STANDARD PROCEDURE, CHECKING POWER STEERING BELT ........7-8
TENSION RELEASE - STANDARD PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER ................5-63
TENSION RESET - STANDARD PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER ................5-64
TENSION SENSOR - DESCRIPTION, BELT . . 8O-8
TENSION SENSOR - OPERATION, BELT ....8O-9
TENSION, SPECIFICATIONS - ACCESSORY DRIVE BELT ................7-5
TENSIONER - 2.4L - INSTALLATION, BELT ............................... 7-11
TENSIONER - 2.4L - REMOVAL, BELT ......7-11
TENSIONER - 3.3/3.8L - INSTALLATION, BELT ............................... 7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-43
TENSIONER - OPERATION, SEAT BELT ....8O-43
TENSIONER & PULLEY - INSTALLATION, TIMING BELT ......................... 9-70
TENSIONER & PULLEY - REMOVAL, TIMING BELT ......................... 9-69
TERMINAL - INSTALLATION .........8W-01-14
TERMINAL - REMOVAL .............8W-01-14
TEST - DIAGNOSIS AND TESTING, CONTROL CIRCUIT ................... 8F-33
TEST - DIAGNOSIS AND TESTING, COOLING SYSTEM LEAK .................7-2 TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE ......................... 9-85,9-9
TEST - DIAGNOSIS AND TESTING, CYLINDER COMPRESSION PRESSURE . . 9-85,9-9
TEST - DIAGNOSIS AND TESTING, FEED CIRCUIT ............................ 8F-36
TEST - DIAGNOSIS AND TESTING, FEED CIRCUIT RESISTANCE .................8F-35
TEST - DIAGNOSIS AND TESTING, POWER STEERING SYSTEM FLOW
AND PRESSURE ...................... 19-1
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING, ROAD ......................... 21-150,21-5
TEST - DIAGNOSIS AND TESTING, STARTING SYSTEM ................... 8F-31
TEST, DIAGNOSIS AND TESTING - A/C COOL DOWN ......................... 24-6
TEST, DIAGNOSIS AND TESTING - A/C PERFORMANCE ....................... 24-7
TEST, DIAGNOSIS AND TESTING - HEATER PERFORMANCE ...............24-10
TEST, DIAGNOSIS AND TESTING - SYSTEM CHARGE LEVEL ...............24-67
TEST MODE, OPERATION - DRB III T
STATE DISPLAY ...................... 25-10
TEST, STANDARD PROCEDURE - IGNITION-OFF DRAW .................. 8F-13
TEST, STANDARD PROCEDURE - OPEN-CIRCUIT VOLTAGE ...............8F-13
TESTER, STANDARD PROCEDURE - MICRO 420 BATTERY .................8F-15
TESTS - DIAGNOSIS AND TESTING, CLUTCH AIR PRESSURE ..........21-153,21-8
TESTS - DIAGNOSIS AND TESTING, HYDRAULIC PRESSURE ..........21-150,21-6
THEFT SECURITY - DESCRIPTION, VEHICLE ............................ 8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING, VEHICLE ................8Q-3
THERMOSTAT - 2.4L - INSTALLATION, ENGINE COOLANT ..................... 7-24
THERMOSTAT - 2.4L - REMOVAL, ENGINE COOLANT ..................... 7-24
THERMOSTAT - 3.3/3.8L - INSTALLATION, ENGINE COOLANT ........7-25
THERMOSTAT - 3.3/3.8L - REMOVAL, ENGINE COOLANT ..................... 7-24
THERMOSTAT - DESCRIPTION, ENGINE COOLANT ............................ 7-23
THERMOSTAT - DIAGNOSIS AND TESTING, ENGINE COOLANT .............7-23
THERMOSTAT - OPERATION, ENGINE COOLANT ............................ 7-23
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE .....23-153
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT .................23-154
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/
FOAM ............................. 23-156
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME .....23-157
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW
STRAP ............................ 23-158
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION
COVER/FOAM ....................... 23-159
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE .........23-152
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT .................... 23-153
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM ....23-155
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME .........23-156
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW STRAP ....23-158
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/
FOAM ............................. 23-159
THIRD ROW - INSTALLATION, BENCH SEAT RISER ........................ 23-145
THIRD ROW - REMOVAL, BENCH SEAT RISER ............................ 23-145THIRD ROW -FOLD-IN-FLOOR -
INSTALLATION, SEAT BACK PANEL ......23-158
THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK PANEL .........23-158
THREAD REPAIR - DESCRIPTION, FRONT CRADLE CROSSMEMBER ..............13-14
THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD STRIPPED ......9-147
THREADS - STANDARD PROCEDURE, REPAIR OF DAMAGED OR WORN .....9-10,9-88
THREE PASSENGER BENCH - INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW ....................... 8O-40
THREE PASSENGER BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW .....8O-40
THREE ZONE, DESCRIPTION - MANUAL ....24-2
THREE ZONE, OPERATION - MANUAL .....24-5
THROTTLE BODY - DESCRIPTION ........14-39
THROTTLE BODY - INSTALLATION .......14-40
THROTTLE BODY - OPERATION .........14-39
THROTTLE BODY - REMOVAL ...........14-40
THROTTLE CONTROL CABLE - INSTALLATION ....................... 14-40
THROTTLE CONTROL CABLE - REMOVAL . . 14-40
THROTTLE POSITION SENSOR - DESCRIPTION ....................... 14-40
THROTTLE POSITION SENSOR - OPERATION ......................... 14-41
TIE ROD - INSTALLATION, OUTER .......19-35
TIE ROD - REMOVAL, OUTER ...........19-34
TIMING BELT - INSTALLATION .............9-67
TIMING BELT - REMOVAL ...............9-65
TIMING BELT COVER(S) - INSTALLATION . . . 9-64
TIMING BELT COVER(S) - REMOVAL ......9-63
TIMING BELT TENSIONER & PULLEY - INSTALLATION ........................ 9-70
TIMING BELT TENSIONER & PULLEY - REMOVAL ........................... 9-69
TIMING CHAIN AND CAMSHAFT SPROCKET - INSTALLATION ............9-160
TIMING CHAIN AND CAMSHAFT SPROCKET - REMOVAL ................9-159
TIMING CHAIN COVER - INSTALLATION . . . 9-157
TIMING CHAIN COVER - REMOVAL ......9-156
TIMING CHAIN WEAR - STANDARD PROCEDURE, MEASURING .............9-155
TIMING VERIFICATION - STANDARD PROCEDURE, VALVE .................. 9-155
TIRE - DESCRIPTION ..................22-13
TIRE AND WHEEL ASSEMBLY (ALUMINUM WHEEL) - INSTALLATION .....22-8
TIRE AND WHEEL ASSEMBLY (ALUMINUM WHEEL) - REMOVAL ........22-8
TIRE AND WHEEL ASSEMBLY (STEEL WHEEL) - INSTALLATION ...............22-8
TIRE AND WHEEL ASSEMBLY (STEEL WHEEL) - REMOVAL ................... 22-8
TIRE AND WHEEL BALANCE - STANDARD PROCEDURE ................22-5
TIRE AND WHEEL MATCH MOUNTING - STANDARD PROCEDURE ................22-7
TIRE AND WHEEL ROTATION - STANDARD PROCEDURE ................22-7
TIRE AND WHEEL VIBRATION - DIAGNOSIS AND TESTING ..............22-1
TIRE INFLATION PRESSURES - STANDARD PROCEDURE ...............22-16
TIRE LEAK REPAIRING - STANDARD PROCEDURE ........................ 22-17
TIRE NOISE - DIAGNOSIS AND TESTING . . 22-14
TIRE PRESSURE FOR HIGH SPEED OPERATION - STANDARD PROCEDURE . . . 22-17
TIRE PRESSURE MONITORING - DESCRIPTION ........................ 22-9
TIRE PRESSURE MONITORING - OPERATION ......................... 22-10
TIRE PRESSURE SENSOR - DIAGNOSIS AND TESTING ....................... 22-11
TIRE (TEMPORARY) - DESCRIPTION, SPARE ............................. 22-14
TIRE WEAR PATTERNS - DIAGNOSIS AND TESTING ....................... 22-16
TIRES - CLEANING ................... 22-18
TIRES - DESCRIPTION, RADIAL-PLY ......22-13
TIRES - DESCRIPTION, REPLACEMENT . . . 22-14
TIRE/VEHICLE LEAD - DIAGNOSIS AND TESTING ........................... 22-14
32 INDEXRS
Description Group-Page Description Group-Page Description Group-Page