2005 CHRYSLER CARAVAN flat tire

PLUMBING - FRONT
DESCRIPTION
CAUTION: The system must be completely empty
before opening any fitting or connection in the
refrigeration system. Open fittings with caution
even after the system has been emptied. If any
pressure is noticed as a fitting is loosened,
retighten fitting and evacuate the system again.
The use of correct wrenches when making connec-
tions is very important. Improper wrenches or
improper use of wrenches can damage the fittings.
The internal parts of the A/C system will remain sta-
ble as long as moisture-free refrigerant and refrig-
erant oil is used. Abnormal amounts of dirt,
moisture or air can upset the chemical stability.
This may cause operational troubles or even seri-
ous damage if present in more than very small
quantities. Before disconnecting a refrigerant line
or hose, clean the outside of the fittings thoroughly
to prevent contamination from entering the refriger-
ant system.
When opening a refrigeration system, have every-
thing you will need to repair the system ready to
minimize the amount of time the system is opened.
Cap or plug all refrigerant line fittings as soon as
they are opened. This will help prevent the entrance
of dirt and moisture. All new lines and components
should be capped or sealed until they are ready to
be used. Before connecting a refrigerant line or
hose, clean the outside of the fittings thoroughly to
prevent contamination from entering the refrigerant
system.
All tools, including the refrigerant dispensing mani-
fold, manifold gauge set and test hoses should be
kept clean and dry.
The A/C refrigerant lines and hoses are used to
carry the refrigerant between the various A/C system
components. The refrigerant lines and hoses for the
R-134a system on this vehicle consist of a barrier-
hose design with a nylon tube sandwiched between
rubber layers. The nylon tube helps to contain the
R-134a refrigerant, which has a smaller molecular
structure than R-12 refrigerant. The ends of the
refrigerant lines are made from lightweight alumi-
num or steel, and commonly use braze-less fittings.Any kinks or sharp bends in the refrigerant lines
and hoses will reduce the capacity of the entire A/C
system and can reduce the flow of refrigerant in the
system. The radius of all bends in the flexible hose
refrigerant lines should be at least ten times the
diameter of the hose and the refrigerant lines should
be routed so they are at least 80 millimeters (3
inches) away from the exhaust manifold(s) and
exhaust pipe(s).
OPERATION
High pressures are produced in the refrigerant sys-
tem when the A/C compressor is operating. Extreme
care must be exercised to make sure that each of the
refrigerant system connections is pressure-tight and
leak free. It is a good practice to inspect all flexible
hose refrigerant lines at least once a year to make
sure they are in good condition and properly routed.
The refrigerant lines and hoses are coupled to
other A/C system components with block-type fit-
tings. An O-ring seal, or a flat steel gasket with an
integral O-ring (dual plane seal), is used to mate the
refrigerant line fittings with A/C system components
to ensure the integrity of the refrigerant system.
The refrigerant lines and hoses cannot be repaired
and, if faulty or damaged, they must be replaced.
WARNING
ENGINE COOLING SYSTEM
WARNING: THE ENGINE COOLING SYSTEM IS
DESIGNED TO DEVELOP INTERNAL PRESSURES
OF 97 TO 123 KILOPASCALS (14 TO 18 POUNDS
PER SQUARE INCH). DO NOT REMOVE OR
LOOSEN THE COOLANT PRESSURE CAP, CYLIN-
DER BLOCK DRAIN PLUGS, RADIATOR DRAIN,
RADIATOR HOSES, HEATER HOSES, OR HOSE
CLAMPS WHILE THE ENGINE COOLING SYSTEM IS
HOT AND UNDER PRESSURE. FAILURE TO
OBSERVE THIS WARNING CAN RESULT IN SERI-
OUS BURNS FROM THE HEATED ENGINE COOL-
ANT. ALLOW THE VEHICLE TO COOL FOR A
MINIMUM OF 15 MINUTES BEFORE OPENING THE
COOLING SYSTEM FOR SERVICE.
RSPLUMBING - FRONT24-65

HYDRAULIC CIRCUITS AND VALVES -OPERATION .......................... 5-95
HYDRAULIC LASH ADJUSTER NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING ............................ 9-34
HYDRAULIC LASH ADJUSTERS - INSTALLATION ........................ 9-35
HYDRAULIC LASH ADJUSTERS - REMOVAL ........................... 9-35
HYDRAULIC LIFTERS - DIAGNOSIS AND TESTING ........................... 9-116
HYDRAULIC LIFTERS (CAM IN BLOCK) - DESCRIPTION ....................... 9-116
HYDRAULIC LIFTERS (CAM IN BLOCK) - INSTALLATION ....................... 9-117
HYDRAULIC LIFTERS (CAM IN BLOCK) - REMOVAL .......................... 9-117
HYDRAULIC PRESSURE TESTS - DIAGNOSIS AND TESTING ........21-150,21-6
HYDRAULIC SCHEMATICS, SCHEMATICS AND DIAGRAMS - 4XTE TRANSAXLE ....21-199,
21-54
HYDROSTATIC LOCKED ENGINE, STANDARD PROCEDURE ............9-10,9-87
ICU - ASSEMBLY ..................... 5-106
ICU - DISASSEMBLY ..................5-105
ICU (INTEGRATED CONTROL UNIT) - DESCRIPTION ....................... 5-102
ICU (INTEGRATED CONTROL UNIT) - OPERATION ......................... 5-102
IDENTIFICATION - DESCRIPTION, VEHICLE ............................ 23-1
IDENTIFICATION AND INFORMATION - DESCRIPTION, SECTION ..............8W-01-6
IDLE AIR CONTROL MOTOR - DESCRIPTION ....................... 14-33
IDLE AIR CONTROL MOTOR - INSTALLATION ....................... 14-33
IDLE AIR CONTROL MOTOR - OPERATION ......................... 14-33
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-33
IGNITION COIL - DESCRIPTION ...........8I-6
IGNITION COIL - OPERATION .............8I-6
IGNITION SENSE - PCM INPUT - OPERATION ......................... 8E-14
IGNITION SWITCH - INSTALLATION ......19-19
IGNITION SWITCH - REMOVAL ..........19-17
IGNITION SYSTEM - DESCRIPTION ........8I-1
IGNITION SYSTEM - OPERATION ..........8I-1
IGNITION-OFF DRAW TEST, STANDARD PROCEDURE ........................ 8F-13
ILLUMINATION LAMPS - INSTALLATION, CLUSTER ........................... 8L-21
ILLUMINATION LAMPS - REMOVAL, CLUSTER ........................... 8L-21
IMPACT SENSOR - DESCRIPTION .......8O-18
IMPACT SENSOR - INSTALLATION .......8O-21
IMPACT SENSOR - REMOVAL ...........8O-19
INBOARD - 50/50 BENCH - INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW ....................... 8O-38
INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW .....8O-37
INBOARD - INSTALLATION, SEAT BELT BUCKLE - FRONT .................... 8O-35
INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW ......................... 8O-36
INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE - FIRST ROW .......8O-35
INBOARD - REMOVAL, SEAT BELT BUCKLE - FRONT .................... 8O-35
INDICATOR - DESCRIPTION, PASSENGER AIRBAG DISABLED ................... 8O-33
INDICATOR - INSTALLATION, PASSENGER AIRBAG DISABLED .........8O-34
INDICATOR - OPERATION, PASSENGER AIRBAG DISABLED ................... 8O-33
INDICATOR - REMOVAL, PASSENGER AIRBAG DISABLED ................... 8O-34
INDICATOR LAMP - DESCRIPTION, VTSS/SKIS .......................... 8Q-8
INDICATOR LAMP - OPERATION, VTSS/SKIS .......................... 8Q-8
INDICATORS - DIAGNOSIS AND TESTING, TREAD WEAR ...............22-16
INFLATABLE KNEE - INSTALLATION, BLOCKER ........................... 23-75INFLATABLE KNEE - REMOVAL,
BLOCKER ........................... 23-75
INFLATION PRESSURES - STANDARD PROCEDURE, TIRE ................... 22-16
INFO CENTER - DESCRIPTION, ELECTRONIC VEHICLE .................8M-7
INFO CENTER - OPERATION, ELECTRONIC VEHICLE .................8M-7
INFRARED TEMPERATURE SENSOR - DESCRIPTION ....................... 24-28
INFRARED TEMPERATURE SENSOR - OPERATION ......................... 24-28
INITIAL OPERATION - STANDARD PROCEDURE, POWER STEERING
PUMP ............................. 19-37
INJECTION SYSTEM - OPERATION .......14-22
INJECTOR - DESCRIPTION, FUEL ........14-30
INJECTOR - OPERATION, FUEL ..........14-31
INLET AIR TEMPERATURE SENSOR - DESCRIPTION ....................... 14-34
INLET FILTER - INSTALLATION ..........14-17
INLET FILTER - REMOVAL ..............14-17
INLET HOSE - INSTALLATION, HEATER ....24-87
INLET HOSE - REMOVAL, HEATER .......24-86
INLET TUBE - 2.4L - DESCRIPTION, WATER PUMP ........................ 7-36
INLET TUBE - 2.4L - INSTALLATION, WATER PUMP ........................ 7-36
INLET TUBE - 2.4L - REMOVAL, WATER PUMP .............................. 7-36
INLET TUBE - 3.3/3.8L - INSTALLATION, WATER PUMP ......................... 7-37
INLET TUBE - 3.3/3.8L - REMOVAL, WATER PUMP ........................ 7-37
INNER - INSTALLATION, CV BOOT .........3-7
INNER - REMOVAL, CV BOOT .............3-6
INNER BELT MOLDING - INSTALLATION, FRONT DOOR ...................... 23-168
INNER BELT MOLDING - REMOVAL, FRONT DOOR ...................... 23-168
INPUT - DESCRIPTION, SPEED SENSOR . 21-120, 21-271
INPUT - INSTALLATION, SPEED SENSOR ..................... 21-121,21-272
INPUT - OPERATION, DATA BUS COMMUNICATION RECEIVE - PCM .......8E-14
INPUT - OPERATION, IGNITION SENSE - PCM............................... 8E-14
INPUT - OPERATION, SENSOR RETURN - PCM............................... 8E-14
INPUT - OPERATION, SPEED SENSOR . . . 21-120, 21-271
INPUT - REMOVAL, SPEED SENSOR ....21-121,
21-272
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-246, 21-95
INPUT CLUTCH ASSEMBLY - DISASSEMBLY ................. 21-237,21-86
INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB
CARPETS ........................... 23-96
INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR
TUB CARPET ........................ 23-98
INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB CARPETS ............23-95
INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET ......23-98
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION .....8J-1
INSTRUMENT PANEL - INSTALLATION, LOWER ............................ 23-73
INSTRUMENT PANEL - REMOVAL, LOWER ............................ 23-73
INSTRUMENT PANEL ANTENNA CABLE - INSTALLATION ....................... 8A-12
INSTRUMENT PANEL ANTENNA CABLE - REMOVAL .......................... 8A-12
INSTRUMENT PANEL ASSEMBLY - INSTALLATION ....................... 23-70
INSTRUMENT PANEL ASSEMBLY - REMOVAL .......................... 23-67
INSTRUMENT PANEL CENTER BEZEL - INSTALLATION ....................... 23-72
INSTRUMENT PANEL CENTER BEZEL - REMOVAL .......................... 23-71
INSTRUMENT PANEL DEMISTER DUCTS - INSTALLATION ..................... 24-54INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL ......................... 24-54
INSTRUMENT PANEL DUCTS - INSTALLATION ....................... 24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL OUTLETS, INSTALLATION ....................... 24-45
INSTRUMENT PANEL OUTLETS, REMOVAL .......................... 24-45
INSTRUMENT PANEL RIGHT END CAP - INSTALLATION ....................... 23-72
INSTRUMENT PANEL RIGHT END CAP - REMOVAL .......................... 23-72
INSTRUMENT PANEL TOP COVER - INSTALLATION ....................... 23-72
INSTRUMENT PANEL TOP COVER - REMOVAL .......................... 23-72
INSTRUMENT PANEL TOP PAD ASSEMBLY - INSTALLATION ............23-77
INSTRUMENT PANEL TOP PAD ASSEMBLY - REMOVAL ................23-77
INTAKE MANIFOLD - DESCRIPTION . . 9-147,9-60
INTAKE MANIFOLD - INSTALLATION, LOWER ............................ 9-151
INTAKE MANIFOLD - INSTALLATION, UPPER ............................. 9-149
INTAKE MANIFOLD - LOWER - CLEANING .......................... 9-151
INTAKE MANIFOLD - LOWER - INSPECTION .................... 9-151,9-62
INTAKE MANIFOLD - LOWER - INSTALLATION ........................ 9-62
INTAKE MANIFOLD - LOWER - REMOVAL ....9-62
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-150
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-148
INTAKE MANIFOLD - UPPER - INSPECTION ......................... 9-61
INTAKE MANIFOLD - UPPER - INSTALLATION ........................ 9-61
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-60
INTAKE MANIFOLD LEAKS - DIAGNOSIS AND TESTING ................... 9-147,9-60
INTAKE MANIFOLD VACUUM PORT REPAIR - STANDARD PROCEDURE .......9-148
INTAKE PIPE - INSTALLATION, AIR ......24-115
INTAKE PIPE - REMOVAL, AIR .........24-115
INTAKE/EXHAUST VALVES & SEATS - CLEANING ...................... 9-108,9-33
INTAKE/EXHAUST VALVES & SEATS - DESCRIPTION ................... 9-107,9-33
INTAKE/EXHAUST VALVES & SEATS - INSPECTION ........................ 9-108
INTAKE/EXHAUST VALVES & SEATS - INSTALLATION ....................... 9-109
INTAKE/EXHAUST VALVES & SEATS - OPERATION ......................... 9-107
INTAKE/EXHAUST VALVES & SEATS - REMOVAL .......................... 9-108
INTEGRAL ANTENNA - EXPORT - DESCRIPTION, QUARTER GLASS ........8A-13
INTEGRAL ANTENNA - EXPORT - OPERATION, QUARTER GLASS ..........8A-13
INTEGRAL ANTENNA, EXPORT - QUARTER GLASS .................... 8A-13
INTEGRATED POWER MODULE - DESCRIPTION .....................8W -97-1
INTEGRATED POWER MODULE - INSTALLATION ....................8W -97-2
INTEGRATED POWER MODULE - OPERATION .......................8W -97-2
INTEGRATED POWER MODULE - REMOVAL ........................8W -97-2
INTERACTIVE SPEED CONTROL (4 SPEED EATX ONLY) - OPERATION ........8P-2
INTERFACE (PCI) BUS, OPERATION - PROGRAMMABLE COMMUNICATIONS ....14-25
INTERIOR LAMPS, SPECIFICATIONS ......8L-20
INTERLOCK SOLENOID - DESCRIPTION, SHIFT ....................... 21-113,21-264
INTERLOCK SOLENOID - DIAGNOSIS AND TESTING, BRAKE/TRANSMISSION
SHIFT ....................... 21-115,21-266
INTERLOCK SOLENOID - INSTALLATION, SHIFT ....................... 21-116,21-267
INTERLOCK SOLENOID - OPERATION, SHIFT ....................... 21-114,21-265
INTERLOCK SOLENOID - REMOVAL, SHIFT ....................... 21-115,21-266
RS INDEX17
Description Group-Page Description Group-Page Description Group-Page

INTERMEDIATE - INSTALLATION, CABLE- PARKING BRAKE ..................... 5-69
INTERMEDIATE - REMOVAL, CABLE - PARKING BRAKE ...................... 5-69
INTERNATIONAL SYMBOLS - DESCRIPTION .........................0-1
INTRODUCTION - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-3,9-78
IOD FUSE - DESCRIPTION ...........8W-97-3
IOD FUSE - OPERATION .............8W-97-3
JOINT - DESCRIPTION, LOWER BALL ......2-10
JOINT - DIAGNOSIS AND TESTING, LOWER BALL ........................ 2-10
JOINT - OPERATION, LOWER BALL .......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-60
JOINT MOLDING - REMOVAL, ROOF ......23-60
JOUNCE BUMPER - DESCRIPTION ........2-35
JOUNCE BUMPER - OPERATION ..........2-35
JUMP STARTING - STANDARD PROCEDURE ......................... 0-25
JUNCTION BLOCK - DESCRIPTION, NON-ABS ............................ 5-33
JUNCTION BLOCK - INSTALLATION, NON-ABS ............................ 5-34
JUNCTION BLOCK - OPERATION, NON-ABS ............................ 5-33
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-34
KEY - DESCRIPTION, TRANSPONDER .....8Q-6
KEY - OPERATION, TRANSPONDER .......8Q-6
KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........23-90
KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ...........23-90
KEY REMOTE ENTRY MODULE - DESCRIPTION, SENTRY ................8Q-3
KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY .......8Q-5
KEY REMOTE ENTRY MODULE - INSTALLATION, SENTRY ................8Q-6
KEY REMOTE ENTRY MODULE - OPERATION, SENTRY .................. 8Q-4
KEY REMOTE ENTRY MODULE - REMOVAL, SENTRY ................... 8Q-6
KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY .......8Q-3
KEYLESS ENTRY TRANSMITTER, DIAGNOSIS AND TESTING .............8N-24
KEYLESS ENTRY TRANSMITTER PROGRAMMING - STANDARD
PROCEDURE, REMOTE ................8N-24
KEY/LOCK CYLINDER - DESCRIPTION ....19-20
KEY/LOCK CYLINDER - INSTALLATION ....19-20
KEY/LOCK CYLINDER - OPERATION ......19-20
KEY/LOCK CYLINDER - REMOVAL .......19-20
KNEE - INSTALLATION, BLOCKER- INFLATABLE ......................... 23-75
KNEE - REMOVAL, BLOCKER- INFLATABLE ......................... 23-75
KNEE BLOCKER AIRBAG - DESCRIPTION . . 8O-22
KNEE BLOCKER AIRBAG - INSTALLATION . 8O-23
KNEE BLOCKER AIRBAG - OPERATION . . . 8O-22
KNEE BLOCKER AIRBAG - REMOVAL .....8O-23
KNOB - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
KNOB - REMOVAL, SEAT BELT HEIGHT ADJUSTER ......................... 8O-38
KNOCK SENSOR - DESCRIPTION ..........8I-8
KNOCK SENSOR - OPERATION ...........8I-8
KNUCKLE - DESCRIPTION ................2-6
KNUCKLE - INSPECTION, STEERING ........2-9
KNUCKLE - INSTALLATION, STEERING ......2-9
KNUCKLE - OPERATION .................2-7
KNUCKLE - REMOVAL, STEERING .........2-7
LABEL, DESCRIPTION - VEHICLE EMISSION CONTROL INFORMATION .......25-1
LAMP - DESCRIPTION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - DIAGNOSIS AND TESTING, FRONT FOG .......................... 8L-7
LAMP - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP - INSTALLATION, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - INSTALLATION, COURTESY ......8L-21
LAMP - INSTALLATION, DOME/CARGO ....8L-22
LAMP - INSTALLATION, FRONT FOG .......8L-8
LAMP - INSTALLATION, LICENSE ........8L-17
LAMP - INSTALLATION, LIFTGATE .......8L-22 LAMP - INSTALLATION, PARK/TURN
SIGNAL ............................ 8L-18
LAMP - INSTALLATION, READING ........8L-23
LAMP - INSTALLATION, TAIL ...........8L-19
LAMP - INSTALLATION, VANITY .........8L-24
LAMP - OPERATION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - REMOVAL, CENTER CONSOLE ....8L-21
LAMP - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - REMOVAL, COURTESY ..........8L-21
LAMP - REMOVAL, DOME/CARGO .......8L-22
LAMP - REMOVAL, FRONT FOG ..........8L-8
LAMP - REMOVAL, LICENSE ............8L-17
LAMP - REMOVAL, LIFTGATE ...........8L-22
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-18
LAMP - REMOVAL, READING ...........8L-22
LAMP - REMOVAL, TAIL ...............8L-18
LAMP - REMOVAL, VANITY .............8L-24
LAMP SWITCH - DESCRIPTION, BRAKE ....8L-4
LAMP SWITCH - DIAGNOSIS AND TESTING, BRAKE ...................... 8L-4
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - INSTALLATION, GLOVE BOX ............................... 8L-22
LAMP SWITCH - OPERATION, BRAKE ......8L-4
LAMP SWITCH - REMOVAL, BRAKE .......8L-5
LAMP SWITCH - REMOVAL, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - REMOVAL, GLOVE BOX . . 8L-22
LAMP UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP .................8L-6
LAMP UNIT - INSTALLATION, TAIL .......8L-19
LAMP UNIT - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP UNIT - REMOVAL, TAIL ...........8L-19
LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG .....8L-9
LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG ...............8L-9
LAMPS - INSTALLATION, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS - REMOVAL, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS, SPECIFICATIONS - EXTERIOR .....8L-3
LAMPS, SPECIFICATIONS - INTERIOR ....8L-20
LAMPS/LIGHTING - EXTERIOR - DESCRIPTION ........................ 8L-2
LAMPS/LIGHTING - EXTERIOR - OPERATION .......................... 8L-2
LAMPS/LIGHTING - EXTERIOR - WARNING ........................... 8L-3
LAP BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER .....23-157
LAP BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER .................. 23-157
LASH ADJUSTER NOISE DIAGNOSIS - DIAGNOSIS AND TESTING, HYDRAULIC ....9-34
LASH ADJUSTERS - INSTALLATION, HYDRAULIC .......................... 9-35
LASH ADJUSTERS - REMOVAL, HYDRAULIC .......................... 9-35
LATCH - DESCRIPTION ...........8N-12,8N-49
LATCH - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID ....23-90
LATCH - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID .................23-90
LATCH - INSTALLATION .....23-18,23-41,23-63
LATCH - INSTALLATION ..........8N-13,8N-50
LATCH - INSTALLATION, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH - INSTALLATION, GLOVE BOX .....23-66
LATCH - INSTALLATION, HOLD OPEN .....23-25
LATCH / LOCK ASSEMBLY - INSTALLATION ....................... 23-27
LATCH / LOCK ASSEMBLY - REMOVAL ....23-26
LATCH - OPERATION ............8N-12,8N-49
LATCH - REMOVAL .........23-18,23-41,23-63
LATCH - REMOVAL ..............8N-12,8N-49
LATCH - REMOVAL, FUEL FILL DOOR BLOCKER ........................... 23-53
LATCH - REMOVAL, GLOVE BOX .........23-66
LATCH - REMOVAL, HOLD OPEN ........23-25
LATCH ACTUATOR - DESCRIPTION ......8N-13
LATCH ACTUATOR - INSTALLATION ......8N-14
LATCH ACTUATOR - OPERATION ........8N-13 LATCH ACTUATOR - REMOVAL
..........8N-13
LATCH CABLE - INSTALLATION, HOLD OPEN .............................. 23-38
LATCH CABLE - REMOVAL, HOLD OPEN . . . 23-38
LATCH HANDLE - INSTALLATION, INSIDE . . 23-34
LATCH HANDLE - REMOVAL, INSIDE .....23-34
LATCH LOCKING LINK - INSTALLATION, SEAT RISER ........................ 23-151
LATCH LOCKING LINK - REMOVAL, SEAT RISER ............................ 23-151
LATCH RELEASE CABLE - INSTALLATION . . 23-64
LATCH RELEASE CABLE - REMOVAL .....23-63
LATCH STRIKER - INSTALLATION . . 23-19,23-42, 23-64
LATCH STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER .................23-53
LATCH STRIKER - INSTALLATION, GLOVE BOX ............................... 23-66
LATCH STRIKER - INSTALLATION, HOLD OPEN .............................. 23-26
LATCH STRIKER - INSTALLATION, REAR . . 23-29
LATCH STRIKER - REMOVAL . 23-19,23-41,23-64
LATCH STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH STRIKER - REMOVAL, GLOVE BOX ............................... 23-66
LATCH STRIKER - REMOVAL, HOLD OPEN .............................. 23-26
LATCH STRIKER - REMOVAL, REAR ......23-29
LEAD - DIAGNOSIS AND TESTING, TIRE/VEHICLE ......................... 22-14
LEAF SPRING FRONT - INSTALLATION, BUSHING ............................ 2-30
LEAF SPRING FRONT - REMOVAL, BUSHING ............................ 2-29
LEAK DETECTION ASSY - INSTALLATION, NATURAL VAC ....................... 25-14
LEAK DETECTION ASSY - REMOVAL, NATURAL VAC ....................... 25-14
LEAK DETECTION PUMP - INSTALLATION . 25-15
LEAK DETECTION PUMP - REMOVAL .....25-15
LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE OIL ...............9-8,9-84
LEAK REPAIRING - STANDARD PROCEDURE, TIRE ................... 22-17
LEAK TEST - DIAGNOSIS AND TESTING, COOLING SYSTEM .....................7-2
LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER HOUSING FLUID . . 21-154, 21-9
LEAKAGE TEST - DIAGNOSIS AND TESTING, CYLINDER COMBUSTION
PRESSURE ....................... 9-85,9-9
LEAKS - DIAGNOSIS AND TESTING, INTAKE MANIFOLD ...............9-147,9-60
LEAKS, DIAGNOSIS AND TESTING - REFRIGERANT SYSTEM ...............24-67
LEAKS, DIAGNOSIS AND TESTING - WATER ............................. 23-1
LEARN CYCLE, STANDARD PROCEDURE - POWER LIFTGATE ................... 8N-8
LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING DOOR ..............8N-48
LEARN PROCEDURE - STANDARD PROCEDURE, QUICK .................. 8E-15
LENS - INSTALLATION, CLUSTER ........8J-11
LENS - REMOVAL, CLUSTER ............8J-11
LEVEL AND CONDITION CHECK, STANDARD PROCEDURE - FLUID . . 21-230,21-82
LEVEL CHECK - STANDARD PROCEDURE, COOLANT .................7-4
LEVEL CHECK - STANDARD PROCEDURE, ENGINE OIL ..............9-140
LEVEL CHECK, STANDARD PROCEDURE - ENGINE OIL ........................ 9-54
LEVEL CHECKING - STANDARD PROCEDURE, BRAKE FLUID .............5-33
LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING FLUID . . . 19-44
LEVEL SENDING UNIT / SENSOR - DESCRIPTION, FUEL ................... 14-5
LEVEL SENDING UNIT / SENSOR - INSTALLATION, FUEL .................. 14-6
LEVEL SENDING UNIT / SENSOR - OPERATION, FUEL ..................... 14-5
LEVEL SENDING UNIT / SENSOR - REMOVAL, FUEL ...................... 14-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

POWER MODULE - INSTALLATION,INTEGRATED ......................8W -97-2
POWER MODULE - OPERATION, INTEGRATED ......................8W -97-2
POWER MODULE - REAR BLOWER MOTOR - DESCRIPTION ...............24-40
POWER MODULE - REAR BLOWER MOTOR - INSTALLATION ...............24-41
POWER MODULE - REAR BLOWER MOTOR - OPERATION .................24-40
POWER MODULE - REAR BLOWER MOTOR - REMOVAL .................. 24-41
POWER MODULE - REMOVAL, INTEGRATED ......................8W -97-2
POWER OUTLET - DESCRIPTION ......8W-97-3
POWER OUTLET - DIAGNOSIS & TESTING .........................8W -97-3
POWER OUTLET - OPERATION ........8W-97-3
POWER SEAT SYSTEM, DESCRIPTION ....8N-31
POWER SEAT SYSTEM, DIAGNOSIS AND TESTING ........................... 8N-33
POWER SEAT SYSTEM, OPERATION .....8N-32
POWER SEAT TRACK - DESCRIPTION ....8N-37
POWER SEAT TRACK - OPERATION ......8N-38
POWER SEAT TRACK, DIAGNOSIS AND TESTING ........................... 8N-38
POWER SLIDING DOOR ADJUSTMENT, STANDARD PROCEDURE ..............8N-49
POWER SLIDING DOOR LEARN CYCLE, STANDARD PROCEDURE ..............8N-48
POWER SLIDING DOOR SYSTEM - DESCRIPTION ........................ 8N-40
POWER SLIDING DOOR SYSTEM - OPERATION ......................... 8N-41
POWER SLIDING DOOR SYSTEM, DIAGNOSIS AND TESTING .............8N-42
POWER STEERING BELT TENSION - STANDARD PROCEDURE, CHECKING .......7-8
POWER STEERING FASTENER TORQUE, SPECIFICATIONS ...................... 19-9
POWER STEERING FLUID LEVEL CHECKING - STANDARD PROCEDURE ....19-44
POWER STEERING GEAR, SPECIAL TOOLS ............................. 19-34
POWER STEERING PUMP INITIAL OPERATION - STANDARD PROCEDURE . . . 19-37
POWER STEERING PUMP, SPECIAL TOOLS ............................. 19-44
POWER STEERING, SPECIAL TOOLS ......19-9
POWER STEERING SYSTEM - DESCRIPTION ........................ 19-1
POWER STEERING SYSTEM - OPERATION .......................... 19-1
POWER STEERING SYSTEM FLOW AND PRESSURE TEST - DIAGNOSIS AND
TESTING ............................ 19-1
POWER TRANSFER UNIT FLUID - DESCRIPTION, AWD ....................0-6
POWER WINDOWS - DESCRIPTION ......8N-61
POWER WINDOWS - OPERATION ........8N-61
POWER WINDOWS, DIAGNOSIS AND TESTING ........................... 8N-61
POWERING SEVERAL LOADS - STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRELOAD - ADJUSTMENT, DIFFERENTIAL BEARING ..............21-228
PRELOAD MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL BEARING ...............21-79
PREPARATION - STANDARD PROCEDURE, ENGINE GASKET
SURFACE ........................ 9-11,9-87
PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE OIL .................9-53
PRESSURE - DIAGNOSIS AND TESTING, ENGINE OIL ......................... 9-138
PRESSURE CAP - DESCRIPTION, RADIATOR ........................... 7-27
PRESSURE CAP - OPERATION, RADIATOR ........................... 7-27
PRESSURE CAP TESTING - DIAGNOSIS AND TESTING, COOLING SYSTEM ........7-28
PRESSURE FOR HIGH SPEED OPERATION - STANDARD PROCEDURE,
TIRE ............................... 22-17
PRESSURE GAUGE - STANDARD PROCEDURE, FUEL .................... 14-3PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION ..................... 9-85,9-9
PRESSURE MONITORING - DESCRIPTION, TIRE ................... 22-9
PRESSURE MONITORING - OPERATION, TIRE ............................... 22-10
PRESSURE REGULATOR - INSTALLATION, FUEL .................. 14-7
PRESSURE REGULATOR - OPERATION, FUEL ............................... 14-7
PRESSURE REGULATOR - REMOVAL, FUEL ............................... 14-7
PRESSURE RELEASE PROCEDURE - STANDARD PROCEDURE, FUEL
SYSTEM ............................ 14-2
PRESSURE RELIEF VALVE - INSTALLATION, OIL ................... 9-144
PRESSURE RELIEF VALVE - REMOVAL, OIL................................ 9-143
PRESSURE RELIEF VALVE, DESCRIPTION - HIGH ............................. 24-72
PRESSURE RELIEF VALVE, OPERATION - HIGH .............................. 24-72
PRESSURE SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER ...............8O-43
PRESSURE SENSOR - DIAGNOSIS AND TESTING, TIRE ...................... 22-11
PRESSURE SENSOR - OPERATION, SEAT WEIGHT BLADDER ................... 8O-44
PRESSURE, SPECIFICATIONS - FUEL SYSTEM ............................ 14-4
PRESSURE SWITCH - DESCRIPTION, OIL . 9-144
PRESSURE SWITCH - INSTALLATION, OIL ........................... 9-144,9-56
PRESSURE SWITCH - OPERATION, OIL . . . 9-144
PRESSURE SWITCH - REMOVAL, OIL ....9-144,
9-56
PRESSURE TEST - DIAGNOSIS AND TESTING, CYLINDER COMPRESSION . . . 9-85,9-9
PRESSURE TEST - DIAGNOSIS AND TESTING, POWER STEERING SYSTEM
FLOW ............................... 19-1
PRESSURE TESTS - DIAGNOSIS AND TESTING, CLUTCH AIR ...........21-153,21-8
PRESSURE TESTS - DIAGNOSIS AND TESTING, HYDRAULIC ............21-150,21-6
PRESSURE TRANSDUCER - DESCRIPTION, A/C ................... 24-20
PRESSURE TRANSDUCER - OPERATION, A/C................................ 24-20
PRESSURE TRANSDUCER, DIAGNOSIS AND TESTING - A/C ................... 24-21
PRESSURES - STANDARD PROCEDURE, TIRE INFLATION ..................... 22-16
PROGRAMMABLE COMMUNICATIONS INTERFACE (PCI) BUS, OPERATION ......14-25
PROGRAMMING - STANDARD PROCEDURE, PCM/SKIM ................8E-1
PROGRAMMING - STANDARD PROCEDURE, REMOTE KEYLESS
ENTRY TRANSMITTER ................8N-24
PROGRAMMING - STANDARD PROCEDURE, TRANSPONDER ...........8Q-6
PROGRAMMING, STANDARD PROCEDURE - ELECTRONIC VEHICLE
INFORMATION CENTER ................8M-8
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-140
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT .............23-139
PROPORTIONING - DESCRIPTION, ELECTRONIC VARIABLE BRAKE ..........5-88
PROPORTIONING - OPERATION, ELECTRONIC VARIABLE BRAKE ..........5-89
PROPORTIONING VALVE (HEIGHT SENSING) - DESCRIPTION ..............5-53
PROPORTIONING VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING .....5-54
PROPORTIONING VALVE (HEIGHT SENSING) - INSTALLATION ..............5-55
PROPORTIONING VALVE (HEIGHT SENSING) - OPERATION ................5-53
PROPORTIONING VALVE (HEIGHT SENSING) - REMOVAL .................5-55
PULLEY - DESCRIPTION, GENERATOR DECOUPLER ........................ 8F-28PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER ..............8F-28
PULLEY - INSTALLATION, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - INSTALLATION, TIMING BELT TENSIONER .......................... 9-70
PULLEY - OPERATION, GENERATOR DECOUPLER ........................ 8F-28
PULLEY - REMOVAL, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - REMOVAL, TIMING BELT TENSIONER .......................... 9-69
PUMP - 2.4L - CLEANING, WATER ........7-32
PUMP - 2.4L - DESCRIPTION, WATER .....7-32
PUMP - 2.4L - INSPECTION, WATER ......7-32
PUMP - 2.4L - INSTALLATION, WATER .....7-32
PUMP - 2.4L - REMOVAL, WATER ........7-32
PUMP - 3.3/3.8L - CLEANING, WATER .....7-35
PUMP - 3.3/3.8L - DESCRIPTION, WATER ............................. 7-34
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-35
PUMP - 3.3/3.8L - INSTALLATION, WATER ............................. 7-35
PUMP - 3.3/3.8L - REMOVAL, WATER .....7-34
PUMP - ASSEMBLY, OIL ...........9-146,9-58
PUMP - ASSEMBLY, OIL ........21-112,21-263
PUMP - CLEANING, OIL ...........9-145,9-57
PUMP - DESCRIPTION, FUEL ............14-8
PUMP - DESCRIPTION, FUEL DOSING . . . 24-117
PUMP - DESCRIPTION, OIL .............9-144
PUMP - DESCRIPTION, OIL ......21-110,21-261
PUMP - DISASSEMBLY, OIL ........9-145,9-57
PUMP - DISASSEMBLY, OIL .....21-110,21-261
PUMP - INSPECTION, OIL ..........9-145,9-58
PUMP - INSTALLATION, FUEL DOSING . . . 24-117
PUMP - INSTALLATION, LEAK DETECTION ......................... 25-15
PUMP - INSTALLATION, OIL ........9-146,9-59
PUMP - INSTALLATION, SEAL - OIL ....21-113,
21-264
PUMP - OPERATION, FUEL ..............14-8
PUMP - OPERATION, FUEL DOSING .....24-117
PUMP - OPERATION, OIL .......21-110,21-261
PUMP - REMOVAL, FUEL DOSING ......24-117
PUMP - REMOVAL, LEAK DETECTION ....25-15
PUMP - REMOVAL, OIL ............9-144,9-56
PUMP - REMOVAL, SEAL - OIL . . . 21-113,21-264
PUMP (2.4L ENGINE) - INSTALLATION ....19-43
PUMP (2.4L ENGINE) - REMOVAL .......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) - DESCRIPTION ....................... 19-36
PUMP (3.3L/3.8L ENGINE) - INSTALLATION ....................... 19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL . . . 19-40
PUMP (DIESEL) - DESCRIPTION .........19-37
PUMP (DIESEL) - INSTALLATION ........19-43
PUMP (DIESEL) - REMOVAL ............19-41
PUMP INITIAL OPERATION - STANDARD PROCEDURE, POWER STEERING ........19-37
PUMP INLET TUBE - 2.4L - DESCRIPTION, WATER .................7-36
PUMP INLET TUBE - 2.4L - INSTALLATION, WATER .................7-36
PUMP INLET TUBE - 2.4L - REMOVAL, WATER ............................. 7-36
PUMP INLET TUBE - 3.3/3.8L - INSTALLATION, WATER .................7-37
PUMP INLET TUBE - 3.3/3.8L - REMOVAL, WATER .................... 7-37
PUMP MODULE - DESCRIPTION, FUEL ....14-8
PUMP MODULE - OPERATION, FUEL ......14-9
PUMP MOTOR - INSTALLATION, WASHER ........................... 8R-12
PUMP MOTOR - REMOVAL, WASHER ....8R-12
PUMP (PULLEY) - ASSEMBLY ..........19-42
PUMP (PULLEY) - DISASSEMBLY ........19-41
PUMP RELAY - DESCRIPTION, FUEL .....14-32
PUMP RELAY - OPERATION, FUEL .......14-32
PUMP, SPECIAL TOOLS - POWER STEERING .......................... 19-44
PUSH-PIN GROMMET REPLACEMENT, STANDARD PROCEDURE ..............8N-48
PUSHRODS - DESCRIPTION ............9-112
PUSHRODS - OPERATION ..............9-112
QUAD BUCKET - INSTALLATION, BUCKET SEAT BACK ........................ 23-141
QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW INBOARD ....8O-36
24 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

TANK - STANDARD PROCEDURE,DRAINING FUEL ...................... 14-2
TANK FILLER TUBE - INSTALLATION, FUEL .............................. 14-17
TANK FILLER TUBE - REMOVAL, FUEL ....14-16
TAPE ATTACHED - INSTALLATION, EXTERIOR NAME PLATES ..............23-51
TAPE ATTACHED - REMOVAL, EXTERIOR NAME PLATES ....................... 23-51
TASK MANAGER - DESCRIPTION ........25-25
TASK MANAGER - OPERATION ..........25-25
TELECOMMUNICATION, DIAGNOSIS AND TESTING ............................8T-1
TEMP SENSOR - DESCRIPTION, AMBIENT .......................... 8M-12
TEMP SENSOR - OPERATION, AMBIENT . . 8M-12
TEMPERATURE CONTROL, DESCRIPTION - AUTOMATIC ........................ 24-3
TEMPERATURE CONTROL, OPERATION - AUTOMATIC .......................... 24-5
TEMPERATURE CONTROL SYSTEM, OPERATION - AUTOMATIC ............24-114
TEMPERATURE CONTROL SYSTEM, OPERATION - MANUAL ...............24-113
TEMPERATURE SENSOR - 2.4L - DESCRIPTION, ENGINE COOLANT .........7-21
TEMPERATURE SENSOR - 2.4L - INSTALLATION, ENGINE COOLANT ........7-21
TEMPERATURE SENSOR - 2.4L - REMOVAL, ENGINE COOLANT ............7-21
TEMPERATURE SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE COOLANT .........7-21
TEMPERATURE SENSOR - 3.3/3.8L - INSTALLATION, ENGINE COOLANT ........7-23
TEMPERATURE SENSOR - 3.3/3.8L - REMOVAL, ENGINE COOLANT ............7-21
TEMPERATURE SENSOR - DESCRIPTION, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - DESCRIPTION, EVAPORATOR ....................... 24-26
TEMPERATURE SENSOR - DESCRIPTION, INFRARED .......................... 24-28
TEMPERATURE SENSOR - DESCRIPTION, INLET AIR .......................... 14-34
TEMPERATURE SENSOR - OPERATION, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - OPERATION, EVAPORATOR ....................... 24-27
TEMPERATURE SENSOR - OPERATION, INFRARED .......................... 24-28
TEMPERATURE SENSOR - REMOVAL, BATTERY ........................... 8F-24
TEMPERATURE SENSOR - SPECIFICATIONS, BATTERY .............8F-23
TEMPERATURE SENSOR CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT ....8M-12
TEMPERATURE SENSOR, DIAGNOSIS AND TESTING - AMBIENT .............8M-12
TENSION - STANDARD PROCEDURE, CHECKING POWER STEERING BELT ........7-8
TENSION RELEASE - STANDARD PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER ................5-63
TENSION RESET - STANDARD PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER ................5-64
TENSION SENSOR - DESCRIPTION, BELT . . 8O-8
TENSION SENSOR - OPERATION, BELT ....8O-9
TENSION, SPECIFICATIONS - ACCESSORY DRIVE BELT ................7-5
TENSIONER - 2.4L - INSTALLATION, BELT ............................... 7-11
TENSIONER - 2.4L - REMOVAL, BELT ......7-11
TENSIONER - 3.3/3.8L - INSTALLATION, BELT ............................... 7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-43
TENSIONER - OPERATION, SEAT BELT ....8O-43
TENSIONER & PULLEY - INSTALLATION, TIMING BELT ......................... 9-70
TENSIONER & PULLEY - REMOVAL, TIMING BELT ......................... 9-69
TERMINAL - INSTALLATION .........8W-01-14
TERMINAL - REMOVAL .............8W-01-14
TEST - DIAGNOSIS AND TESTING, CONTROL CIRCUIT ................... 8F-33
TEST - DIAGNOSIS AND TESTING, COOLING SYSTEM LEAK .................7-2 TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE ......................... 9-85,9-9
TEST - DIAGNOSIS AND TESTING, CYLINDER COMPRESSION PRESSURE . . 9-85,9-9
TEST - DIAGNOSIS AND TESTING, FEED CIRCUIT ............................ 8F-36
TEST - DIAGNOSIS AND TESTING, FEED CIRCUIT RESISTANCE .................8F-35
TEST - DIAGNOSIS AND TESTING, POWER STEERING SYSTEM FLOW
AND PRESSURE ...................... 19-1
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING, ROAD ......................... 21-150,21-5
TEST - DIAGNOSIS AND TESTING, STARTING SYSTEM ................... 8F-31
TEST, DIAGNOSIS AND TESTING - A/C COOL DOWN ......................... 24-6
TEST, DIAGNOSIS AND TESTING - A/C PERFORMANCE ....................... 24-7
TEST, DIAGNOSIS AND TESTING - HEATER PERFORMANCE ...............24-10
TEST, DIAGNOSIS AND TESTING - SYSTEM CHARGE LEVEL ...............24-67
TEST MODE, OPERATION - DRB III T
STATE DISPLAY ...................... 25-10
TEST, STANDARD PROCEDURE - IGNITION-OFF DRAW .................. 8F-13
TEST, STANDARD PROCEDURE - OPEN-CIRCUIT VOLTAGE ...............8F-13
TESTER, STANDARD PROCEDURE - MICRO 420 BATTERY .................8F-15
TESTS - DIAGNOSIS AND TESTING, CLUTCH AIR PRESSURE ..........21-153,21-8
TESTS - DIAGNOSIS AND TESTING, HYDRAULIC PRESSURE ..........21-150,21-6
THEFT SECURITY - DESCRIPTION, VEHICLE ............................ 8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING, VEHICLE ................8Q-3
THERMOSTAT - 2.4L - INSTALLATION, ENGINE COOLANT ..................... 7-24
THERMOSTAT - 2.4L - REMOVAL, ENGINE COOLANT ..................... 7-24
THERMOSTAT - 3.3/3.8L - INSTALLATION, ENGINE COOLANT ........7-25
THERMOSTAT - 3.3/3.8L - REMOVAL, ENGINE COOLANT ..................... 7-24
THERMOSTAT - DESCRIPTION, ENGINE COOLANT ............................ 7-23
THERMOSTAT - DIAGNOSIS AND TESTING, ENGINE COOLANT .............7-23
THERMOSTAT - OPERATION, ENGINE COOLANT ............................ 7-23
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE .....23-153
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT .................23-154
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/
FOAM ............................. 23-156
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME .....23-157
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW
STRAP ............................ 23-158
THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION
COVER/FOAM ....................... 23-159
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE .........23-152
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT .................... 23-153
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM ....23-155
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME .........23-156
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW STRAP ....23-158
THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/
FOAM ............................. 23-159
THIRD ROW - INSTALLATION, BENCH SEAT RISER ........................ 23-145
THIRD ROW - REMOVAL, BENCH SEAT RISER ............................ 23-145THIRD ROW -FOLD-IN-FLOOR -
INSTALLATION, SEAT BACK PANEL ......23-158
THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK PANEL .........23-158
THREAD REPAIR - DESCRIPTION, FRONT CRADLE CROSSMEMBER ..............13-14
THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD STRIPPED ......9-147
THREADS - STANDARD PROCEDURE, REPAIR OF DAMAGED OR WORN .....9-10,9-88
THREE PASSENGER BENCH - INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW ....................... 8O-40
THREE PASSENGER BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW .....8O-40
THREE ZONE, DESCRIPTION - MANUAL ....24-2
THREE ZONE, OPERATION - MANUAL .....24-5
THROTTLE BODY - DESCRIPTION ........14-39
THROTTLE BODY - INSTALLATION .......14-40
THROTTLE BODY - OPERATION .........14-39
THROTTLE BODY - REMOVAL ...........14-40
THROTTLE CONTROL CABLE - INSTALLATION ....................... 14-40
THROTTLE CONTROL CABLE - REMOVAL . . 14-40
THROTTLE POSITION SENSOR - DESCRIPTION ....................... 14-40
THROTTLE POSITION SENSOR - OPERATION ......................... 14-41
TIE ROD - INSTALLATION, OUTER .......19-35
TIE ROD - REMOVAL, OUTER ...........19-34
TIMING BELT - INSTALLATION .............9-67
TIMING BELT - REMOVAL ...............9-65
TIMING BELT COVER(S) - INSTALLATION . . . 9-64
TIMING BELT COVER(S) - REMOVAL ......9-63
TIMING BELT TENSIONER & PULLEY - INSTALLATION ........................ 9-70
TIMING BELT TENSIONER & PULLEY - REMOVAL ........................... 9-69
TIMING CHAIN AND CAMSHAFT SPROCKET - INSTALLATION ............9-160
TIMING CHAIN AND CAMSHAFT SPROCKET - REMOVAL ................9-159
TIMING CHAIN COVER - INSTALLATION . . . 9-157
TIMING CHAIN COVER - REMOVAL ......9-156
TIMING CHAIN WEAR - STANDARD PROCEDURE, MEASURING .............9-155
TIMING VERIFICATION - STANDARD PROCEDURE, VALVE .................. 9-155
TIRE - DESCRIPTION ..................22-13
TIRE AND WHEEL ASSEMBLY (ALUMINUM WHEEL) - INSTALLATION .....22-8
TIRE AND WHEEL ASSEMBLY (ALUMINUM WHEEL) - REMOVAL ........22-8
TIRE AND WHEEL ASSEMBLY (STEEL WHEEL) - INSTALLATION ...............22-8
TIRE AND WHEEL ASSEMBLY (STEEL WHEEL) - REMOVAL ................... 22-8
TIRE AND WHEEL BALANCE - STANDARD PROCEDURE ................22-5
TIRE AND WHEEL MATCH MOUNTING - STANDARD PROCEDURE ................22-7
TIRE AND WHEEL ROTATION - STANDARD PROCEDURE ................22-7
TIRE AND WHEEL VIBRATION - DIAGNOSIS AND TESTING ..............22-1
TIRE INFLATION PRESSURES - STANDARD PROCEDURE ...............22-16
TIRE LEAK REPAIRING - STANDARD PROCEDURE ........................ 22-17
TIRE NOISE - DIAGNOSIS AND TESTING . . 22-14
TIRE PRESSURE FOR HIGH SPEED OPERATION - STANDARD PROCEDURE . . . 22-17
TIRE PRESSURE MONITORING - DESCRIPTION ........................ 22-9
TIRE PRESSURE MONITORING - OPERATION ......................... 22-10
TIRE PRESSURE SENSOR - DIAGNOSIS AND TESTING ....................... 22-11
TIRE (TEMPORARY) - DESCRIPTION, SPARE ............................. 22-14
TIRE WEAR PATTERNS - DIAGNOSIS AND TESTING ....................... 22-16
TIRES - CLEANING ................... 22-18
TIRES - DESCRIPTION, RADIAL-PLY ......22-13
TIRES - DESCRIPTION, REPLACEMENT . . . 22-14
TIRE/VEHICLE LEAD - DIAGNOSIS AND TESTING ........................... 22-14
32 INDEXRS
Description Group-Page Description Group-Page Description Group-Page