2005 CHRYSLER CARAVAN wheel alignment

(2) Position door to vehicle. Verify net pierce nub-
bin is engaged if reusing original hinges. Applies to
body half of hinge only.
(3) Steady door on lifting device and install bolts
attaching upper hinge to door end frame. Tighten
bolts to 34 N´m (25 ft. lbs.) torque.
(4) Install bolts attaching lower hinge to door end
frame. Tighten bolts to 34 N´m (25 ft. lbs.) torque.
Align door to achieve equal spacing to surrounding
body panels. Panels should be flush across all gaps.
(5) Install bolts attaching door check strap to
A-pillar. Tighten bolts to 12 N´m (105 in. lbs.) torque.
(6) Connect door harness into body wiring harness.
(7) Connect positive lock slide on the side of the
wire connectors.
(8) Connect clips attaching door harness wire con-
nector to inner fender brace.
(9) Install front wheelhouse splash shield.
(10) Verify door operation and alignment. Adjust
as necessary.
DOOR GLASS
REMOVAL
(1) Remove watershield. (Refer to 23 - BODY/
DOOR - FRONT/WATERSHIELD - REMOVAL)
(2) Remove inner belt molding.(Refer to 23 -
BODY/WEATHERSTRIP/SEALS/FDR INNER BELT
WEATHERSTRIP - REMOVAL)
Fig. 3 FRONT DOOR WIRE CONNECTORS
1 - LOCK TAB
2 - POSITIVE LOCK
3 - BODY HARNESS CONNECTOR
4 - FRONT FENDER
5 - DOOR HARNESS CONNECTOR
6 - BODY HARNESS
Fig. 4 FRONT DOOR - HINGE PIN REMOVAL
1 - FRONT DOOR
2 - CLIP
3 - A-PILLAR
4 - HINGE PIN
5 - CLIP
6 - DOOR CHECK STRAP
Fig. 5 FRONT DOOR - HINGE BOLT REMOVAL
1 - FRONT DOOR
2 - UPPER HINGE
3 - CHECK STRAP
4 - LOWER HINGE
23 - 16 DOOR - FRONTRS
DOOR (Continued)

(2) Insert ends of crossmember between layered
metal sections of radiator closure panel at each side
of radiator.
(3) Align with paint breaks around bolt heads.
(4) Install bolts attaching ends of crossmember to
radiator closure panel (Fig. 16). Tighten bolts to 19
N´m (14 ft. lbs.) torque.
(5) Install bolts attaching radiator isolators to
crossmember.
(6) Install screw attaching coolant recovery bottle
to crossmember.
(7) Install bolt attaching air cleaner housing to
crossmember.
(8) Install engine air inlet resonator.
(9) Install hood prop rod.
(10) Align hood latch by placing latch over net
pierce tabs. If alignment is required, flatten tabs.
(11) Install bolts attaching hood latch to cross-
member and clip cable. Tighten bolts to 13.5 N´m (10
ft. lbs.) torque.
(12) Install radiator sight shield.
(13) Verify hood latch operation and hood align-
ment.
FRONT WHEELHOUSE
SPLASH SHIELD
REMOVAL
(1) Hoist and support vehicle on safety stands.
(Refer to LUBRICATION & MAINTENANCE/HOIST-
ING - STANDARD PROCEDURE).
(2) Remove front wheel.
(3) Remove push pin fasteners attaching splash
shield to frame rail forward of suspension.
(4) Remove push pin fasteners attaching splash
shield to frame rail rearward of suspension.
(5) Remove screws attaching wheelhouse splash
shield to front fender and front bumper fascia.
(6) Remove splash shield from vehicle (Fig. 17).
INSTALLATION
(1) Place splash shield in position on vehicle (Fig.
17).
(2) Install push pin fasteners attaching splash
shield to frame rail forward of suspension.
(3) Install push pin fasteners attaching splash
shield to frame rail rearward of suspension.
(4) Install screws attaching wheelhouse splash
shield to front fender.
(5) Install front wheel.
(6) Lower vehicle.
LUGGAGE RACK RISER
REMOVAL
(1) Remove two fasteners from the front riser.
Gently pull up on the luggage rack side rail and
detach the riser snap to remove riser from the rail
(Fig. 18).
(2) Repeat for the opposite side, if necessary.
(3) Remove front riser(s) from vehicle (Fig. 19).
Fig. 17 FRONT WHEELHOUSE SPLASH SHIELD
1 - FRONT FENDER WHEELHOUSE SPLASH SHIELD
2 - PUSH PIN FASTENERS
3 - ACCESSORY DRIVE SPLASH SHIELD
4 - SCREWS
Fig. 18 LUGGAGE RACK RISER COVER
1 - FRONT RISER COVER
2 - LOCK TABS
3 - LUGGAGE RACK SIDE RAIL
4 - FRONT RISER
RSEXTERIOR23-57
UPPER RADIATOR CROSSMEMBER (Continued)

AJAR SWITCH - EXPORT -INSTALLATION, HOOD .................8Q-3
AJAR SWITCH - EXPORT - REMOVAL, HOOD .............................. 8Q-3
ALIGNMENT - DESCRIPTION, WHEEL ......2-47
ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT .....8L-9
ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT .........8L-15
ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ................8L-9
ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ARM ................... 8R-9
ALIGNMENT - STANDARD PROCEDURE, HEADLAMP UNIT ..................... 8L-14
ALIGNMENT - STANDARD PROCEDURE, WHEEL ............................. 2-52
ALIGNMENT, SPECIFICATIONS - WHEEL ....2-56
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-12
AMBIENT TEMP SENSOR - OPERATION . . 8M-12
AMBIENT TEMPERATURE SENSOR CIRCUIT, DIAGNOSIS AND TESTING .....8M-12
AMBIENT TEMPERATURE SENSOR, DIAGNOSIS AND TESTING .............8M-12
AMPLIFIER - INSTALLATION .............8A-7
AMPLIFIER - REMOVAL ................8A-7
AN AIRBAG DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER ...........8O-7
ANCHOR - DESCRIPTION, CHILD RESTRAINT .......................... 8O-9
ANCHOR - OPERATION, CHILD RESTRAINT .......................... 8O-10
ANTENNA - EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - EXPORT - OPERATION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - NAVIGATION RADIO - INSTALLATION ....................... 8A-11
ANTENNA - NAVIGATION RADIO - REMOVAL .......................... 8A-11
ANTENNA BODY AND CABLE - DESCRIPTION ........................ 8A-7
ANTENNA BODY AND CABLE - OPERATION .......................... 8A-7
ANTENNA BODY AND CABLE, DIAGNOSIS AND TESTING ..............8A-8
ANTENNA CABLE - INSTALLATION, INSTRUMENT PANEL .................8A-12
ANTENNA CABLE - REMOVAL, INSTRUMENT PANEL .................8A-12
ANTENNA, EXPORT - QUARTER GLASS INTEGRAL .......................... 8A-13
ANTENNA MODULE - EXPORT - DESCRIPTION ....................... 8A-10
ANTENNA MODULE - EXPORT - OPERATION ......................... 8A-10
ANTENNA MODULE, EXPORT ...........8A-10
ANTILOCK BRAKE - DESCRIPTION, CONTROLLER ........................ 8E-4
ANTILOCK BRAKE - INSTALLATION, CONTROLLER ........................ 8E-6
ANTILOCK BRAKE - OPERATION, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE - REMOVAL, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE SYSTEM - DESCRIPTION ........................ 5-87
ANTILOCK BRAKE SYSTEM - OPERATION . . 5-88
ANTILOCK BRAKE SYSTEM BLEEDING - STANDARD PROCEDURE ................5-90
ANTILOCK BRAKE SYSTEM (EXPORT) - DESCRIPTION ........................ 5-87
A-PILLAR LOWER EXTENSION TRIM - INSTALLATION ....................... 23-79
A-PILLAR LOWER EXTENSION TRIM - REMOVAL .......................... 23-79
A-PILLAR TRIM - INSTALLATION ........23-79
A-PILLAR TRIM - REMOVAL ............23-79
A-PILLAR-HEADER, OR B-PILLAR - INSTALLATION ....................... 23-17
A-PILLAR-HEADER, OR B-PILLAR - REMOVAL .......................... 23-17
APPLIQUE - INSTALLATION .............23-14
APPLIQUE - REMOVAL ................23-14
ARM - DESCRIPTION, LOWER CONTROL . . . 2-12
ARM - INSPECTION, LOWER CONTROL ....2-14
ARM - INSTALLATION, LOWER CONTROL . . 2-15
ARM - INSTALLATION, REAR WIPER .....8R-10 ARM - OPERATION, LOWER CONTROL
.....2-12
ARM - REMOVAL, LOWER CONTROL ......2-12
ARM - REMOVAL, REAR WIPER .........8R-10
ARM ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ............8R-9
ARM (REAR BUSHING - HYDRO) - ASSEMBLY, LOWER CONTROL ...........2-15
ARM (REAR BUSHING - HYDRO) - DISASSEMBLY, LOWER CONTROL ........2-13
ARM (REAR BUSHING - STANDARD) - ASSEMBLY, LOWER CONTROL ...........2-14
ARM (REAR BUSHING - STANDARD) - DISASSEMBLY, LOWER CONTROL ........2-13
ARMREST - INSTALLATION ............23-108
ARMREST - REMOVAL ...............23-108
ARMREST - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION ..............23-130
ARMREST - SECOND ROW - FOLD-IN- FLOOR - REMOVAL .................. 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION ...................... 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
REMOVAL ......................... 23-130
ARMS - DESCRIPTION, ROCKER ........9-112
ARMS - INSPECTION, ROCKER ...........9-35
ARMS - INSTALLATION, FRONT WIPER ....8R-9
ARMS - INSTALLATION, ROCKER .........9-35
ARMS - OPERATION, ROCKER ..........9-112
ARMS - REMOVAL, FRONT WIPER .........8R-9
ARMS - REMOVAL, ROCKER .............9-35
ARMS AND SHAFT - ASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - DISASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - INSTALLATION, ROCKER ............................ 9-113
ARMS AND SHAFT - REMOVAL, ROCKER . . 9-112
ASSIST DISPLAY - DESCRIPTION, PARK . . . 8B-3
ASSIST DISPLAY - INSTALLATION, PARK . . . 8B-4
ASSIST DISPLAY - OPERATION, PARK .....8B-3
ASSIST DISPLAY - REMOVAL, PARK ......8B-4
ASSIST HANDLE - INSTALLATION ........23-79
ASSIST HANDLE - REMOVAL ...........23-79
ASSIST MODULE - DESCRIPTION, PARK . . . 8B-4
ASSIST MODULE - INSTALLATION, PARK . . 8B-6
ASSIST MODULE - OPERATION, PARK .....8B-5
ASSIST MODULE - REMOVAL, PARK ......8B-5
ASSIST SENSOR - DESCRIPTION, PARK . . . 8B-6
ASSIST SENSOR - INSTALLATION, PARK . . . 8B-6
ASSIST SENSOR - OPERATION, PARK .....8B-6
ASSIST SENSOR - REMOVAL, PARK ......8B-6
ASSIST STRAP - INSTALLATION, FRONT SEAT BACK ........................ 23-112
ASSIST STRAP - REMOVAL, FRONT SEAT BACK ........................ 23-112
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - ADHESIVE .............23-51
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - TAPE .................23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - ADHESIVE .................. 23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - TAPE ...................... 23-51
AUDIO/VIDEO - DESCRIPTION ...........8A-1
AUDIO/VIDEO, DIAGNOSIS AND TESTING . . 8A-2
AUTO SHUT DOWN RELAY - DESCRIPTION ......................... 8I-3
AUTO SHUT DOWN RELAY - OPERATION . . . 8I-3
AUTOMATIC ADJUSTER - DIAGNOSIS AND TESTING, DRUM BRAKE ............5-14
AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD PROCEDURE,
PARKING BRAKE ...................... 5-63
AUTOMATIC ADJUSTER TENSION RESET - STANDARD PROCEDURE, PARKING
BRAKE .............................. 5-64
AUTOMATIC DAY / NIGHT MIRROR - DESCRIPTION ....................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR - OPERATION ......................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR, DIAGNOSIS AND TESTING .............8N-28
AUTOMATIC TEMPERATURE CONTROL, DESCRIPTION ........................ 24-3
AUTOMATIC TEMPERATURE CONTROL, OPERATION .......................... 24-5AUTOMATIC TEMPERATURE CONTROL
SYSTEM, OPERATION ................24-114
AUTOMATIC TRANSAXLE - DESCRIPTION, 40TE ................... 21-2
AUTOMATIC TRANSAXLE - DESCRIPTION, 41TE .................21-147
AUTOMATIC TRANSAXLE - OPERATION, 40TE ............................... 21-4
AUTOMATIC TRANSAXLE - OPERATION, 41TE ............................. 21-149
AUTOMATIC TRANSAXLE, SPECIAL TOOLS - 41TE ...................... 21-213
AUTOMATIC/MANUAL TRANSAXLE FLUID - DESCRIPTION ........................0-4
AWD - INSTALLATION ..................2-45
AWD - INSTALLATION, REAR WHEEL SPEED SENSOR ....................... 5-92
AWD - INSTALLATION, SPRING ..........2-39
AWD - REMOVAL ..................... 2-44
AWD - REMOVAL, REAR WHEEL SPEED SENSOR ............................ 5-92
AWD - REMOVAL, SPRING ..............2-38
AWD, HEAVY DUTY, CARGO - INSTALLATION ........................ 2-36
AWD, HEAVY DUTY, CARGO - REMOVAL . . . 2-36
AWD POWER TRANSFER UNIT FLUID - DESCRIPTION .........................0-6
AWD REAR DRIVELINE MODULE FLUIDS - DESCRIPTION ........................0-6
B OR C-PILLAR - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ..............8O-38
B OR C-PILLAR - REMOVAL, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
BACK - INSTALLATION, BENCH SEAT ....23-147
BACK - INSTALLATION, FRONT SEAT ....23-111
BACK - QUAD BUCKET - INSTALLATION, BUCKET SEAT ...................... 23-141
BACK - QUAD BUCKET - REMOVAL, BUCKET SEAT ...................... 23-140
BACK - REMOVAL, BENCH SEAT ........23-147
BACK - REMOVAL, FRONT SEAT ........23-111
BACK ASSIST STRAP - INSTALLATION, FRONT SEAT ....................... 23-112
BACK ASSIST STRAP - REMOVAL, FRONT SEAT ....................... 23-112
BACK COVER - INSTALLATION, BENCH SEAT ............................. 23-148
BACK COVER - INSTALLATION, FRONT SEAT ............................. 23-116
BACK COVER - REMOVAL, BENCH SEAT . . 23-148
BACK COVER - REMOVAL, FRONT SEAT . . 23-113
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-133
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-133
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-156
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-155
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-134
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-134
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-157
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-156
BACK HINGE - REMOVAL, BENCH SEAT . . 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION,
SEAT ............................. 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT . . 23-146
BACK PANEL - INSTALLATION, BENCH SEAT ............................. 23-144
BACK PANEL - INSTALLATION, FRONT SEAT ............................. 23-113
BACK PANEL - REMOVAL, BENCH SEAT . . 23-143
BACK PANEL - REMOVAL, FRONT SEAT . . 23-112
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT ............................. 23-134
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT .....23-134
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-158
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - REMOVAL, SEAT .............23-158
2 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FOLD-IN-FLOOR - REMOVAL, SEATCUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT - SECOND ROW ...............23-138
FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD - SECOND ROW ................23-139
FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET INSERT .......23-98
FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - REMOVAL, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - SPECIFICATIONS, WELD LOCATIONS ................... 23-350
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY SEALING
LOCATIONS ........................ 23-209
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, STRUCTURAL
ADHESIVE LOCATIONS ...............23-228
FOLD-IN-FLOOR SEATING - INSTALLATION .................... 5-68,5-75
FOLD-IN-FLOOR SEATING - INSTALLATION, FWD ................... 2-45
FOLD-IN-FLOOR SEATING - REMOVAL . 5-66,5-72
FOLD-IN-FLOOR SEATING - REMOVAL, FWD................................ 2-45
FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS .....13-11
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FORWARD ............23-137
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FORWARD ................23-137
FORM-IN-PLACE GASKETS AND SEALERS, STANDARD PROCEDURE . . . 9-11,9-86
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FOLD ................23-160
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FOLD .................... 23-160
FRAME - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT BACK ....23-134
FRAME - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT BACK ........23-134
FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-157
FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-156
FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS .........13-11
FRAME DIMENSIONS - SPECIFICATIONS . . . 13-6
FREE MODULE - INSTALLATION, HANDS . . . 8T-3
FREE MODULE - REMOVAL, HANDS .......8T-3
FRONT - DESCRIPTION, HALF SHAFT .......3-1
FRONT - DESCRIPTION, PLUMBING ......24-65
FRONT - INSTALLATION, BUSHING - LEAF SPRING ........................ 2-30
FRONT - INSTALLATION, CRANKSHAFT OIL SEAL ....................... 9-130,9-42
FRONT - INSTALLATION, HALF SHAFT ......3-4
FRONT - INSTALLATION, SEAT BELT & RETRACTOR - OUTBOARD .............8O-39
FRONT - INSTALLATION, SPRING MOUNTS ............................ 2-43
FRONT - INSTALLATION, WHEEL MOUNTING STUDS ................... 22-21
FRONT - OPERATION, PLUMBING ........24-65
FRONT - REMOVAL, BUSHING - LEAF SPRING ............................. 2-29
FRONT - REMOVAL, CRANKSHAFT OIL SEAL .......................... 9-130,9-41
FRONT - REMOVAL, HALF SHAFT ..........3-2
FRONT - REMOVAL, SEAT BELT & RETRACTOR - OUTBOARD .............8O-38
FRONT - REMOVAL, SPRING MOUNTS .....2-42
FRONT - REMOVAL, WHEEL MOUNTING STUDS ............................. 22-21
FRONT - SPECIFICATIONS, HALF SHAFT ....3-6FRONT A/C EXPANSION VALVE,
DIAGNOSIS AND TESTING .............24-82
FRONT BLOWER MOTOR, DIAGNOSIS AND TESTING ....................... 24-46
FRONT BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING .......24-25
FRONT BRAKE ROTOR - INSTALLATION ....5-59
FRONT BRAKE ROTOR - REMOVAL .......5-59
FRONT BUMPER REINFORCEMENT - INSTALLATION ........................ 13-3
FRONT BUMPER REINFORCEMENT - REMOVAL ........................... 13-3
FRONT CABLE - INSTALLATION, PARKING BRAKE LEVER ................5-77
FRONT CABLE - REMOVAL, PARKING BRAKE LEVER ........................ 5-77
FRONT CENTER BEZEL OUTLETS, INSTALLATION ....................... 24-45
FRONT CENTER BEZEL OUTLETS, REMOVAL .......................... 24-44
FRONT CONTROL MODULE - DESCRIPTION ........................ 8E-7
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE, DIAGNOSIS AND TESTING ........................ 8E-7
FRONT CRADLE CROSSMEMBER - DESCRIPTION ....................... 13-14
FRONT CRADLE CROSSMEMBER THREAD REPAIR - DESCRIPTION ........13-14
FRONT CROSSMEMBER MOUNT BUSHINGS - INSTALLATION ............13-17
FRONT CROSSMEMBER MOUNT BUSHINGS - REMOVAL .................13-17
FRONT DEMISTER OUTLETS, INSTALLATION ....................... 24-45
FRONT DEMISTER OUTLETS, REMOVAL . . . 24-44
FRONT DISC BRAKE CALIPER ADAPTER - INSTALLATION ...................... 5-31
FRONT DISC BRAKE CALIPER ADAPTER - REMOVAL .......................... 5-31
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-27
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-24
FRONT DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION ...............5-27
FRONT DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL .................. 5-24
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-16
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-15
FRONT DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION ...............5-17
FRONT DISC BRAKE SHOES (TRW BRAKES) - REMOVAL .................. 5-15
FRONT DOOR GLASS RUN WEATHERSTRIP - INSTALLATION .......23-166
FRONT DOOR GLASS RUN WEATHERSTRIP - REMOVAL ...........23-166
FRONT DOOR INNER BELT MOLDING - INSTALLATION ...................... 23-168
FRONT DOOR INNER BELT MOLDING - REMOVAL ......................... 23-168
FRONT DOOR OUTER BELT MOLDING - INSTALLATION ...................... 23-167
FRONT DOOR OUTER BELT MOLDING - REMOVAL ......................... 23-167
FRONT DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
FRONT DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
FRONT FASCIA - INSTALLATION ..........13-1
FRONT FASCIA - REMOVAL ..............13-1
FRONT FENDER - INSTALLATION ........23-52
FRONT FENDER - REMOVAL ............23-51
FRONT FOG LAMP - DIAGNOSIS AND TESTING ............................ 8L-7
FRONT FOG LAMP - INSTALLATION .......8L-8
FRONT FOG LAMP - REMOVAL ...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .......8L-9
FRONT FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE ................8L-9FRONT HEATER CORE, INSTALLATION
....24-86
FRONT HEATER CORE, REMOVAL ........24-85
FRONT HEATER CORE TUBES, INSTALLATION ....................... 24-85
FRONT HEATER CORE TUBES, REMOVAL . . 24-84
FRONT INBOARD - INSTALLATION, SEAT BELT BUCKLE ....................... 8O-35
FRONT INBOARD - REMOVAL, SEAT BELT BUCKLE ....................... 8O-35
FRONT MOUNT - INSTALLATION ....9-134,9-50
FRONT MOUNT - REMOVAL ........9-134,9-50
FRONT SEAT - INSTALLATION ..........23-110
FRONT SEAT - REMOVAL .............23-108
FRONT SEAT BACK - INSTALLATION .....23-111
FRONT SEAT BACK - REMOVAL ........23-111
FRONT SEAT BACK ASSIST STRAP - INSTALLATION ...................... 23-112
FRONT SEAT BACK ASSIST STRAP - REMOVAL ......................... 23-112
FRONT SEAT BACK COVER - INSTALLATION ...................... 23-116
FRONT SEAT BACK COVER - REMOVAL . . 23-113
FRONT SEAT BACK PANEL - INSTALLATION ...................... 23-113
FRONT SEAT BACK PANEL - REMOVAL . . 23-112
FRONT SEAT CUSHION - INSTALLATION . . 23-118
FRONT SEAT CUSHION - OCS - INSTALLATION ...................... 23-120
FRONT SEAT CUSHION - OCS - REMOVAL ........................... 23-119
FRONT SEAT CUSHION - REMOVAL .....23-117
FRONT SEAT CUSHION SIDE COVER - INSTALLATION ...................... 23-121
FRONT SEAT CUSHION SIDE COVER - OCS - INSTALLATION ................23-122
FRONT SEAT CUSHION SIDE COVER - OCS - REMOVAL .................... 23-121
FRONT SEAT CUSHION SIDE COVER - REMOVAL ......................... 23-120
FRONT SEAT RISER - MANUAL - OCS - INSTALLATION ...................... 23-123
FRONT SEAT RISER - MANUAL - OCS - REMOVAL ......................... 23-123
FRONT SEAT TRACK - REAR COVER - INSTALLATION ...................... 23-128
FRONT SEAT TRACK - REAR COVER - REMOVAL ......................... 23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION ...............23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL ................... 23-126
FRONT SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION ...............23-125
FRONT SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL ................... 23-124
FRONT SEAT TRACK MANUAL ADJUSTER - INSTALLATION ...........23-126
FRONT SEAT TRACK MANUAL ADJUSTER - REMOVAL ...............23-125
FRONT SEAT TRACK POWER ADJUSTER - INSTALLATION .................... 23-124
FRONT SEAT TRACK POWER ADJUSTER - REMOVAL ........................ 23-124
FRONT SEAT TRACK REAR COVER - OCS - INSTALLATION .................... 23-129
FRONT SEAT TRACK REAR COVER - OCS - REMOVAL ........................ 23-129
FRONT SUSPENSION - DESCRIPTION ......2-2
FRONT SUSPENSION - OPERATION ........2-2
FRONT SUSPENSION FASTENER TORQUE, SPECIFICATIONS ...............2-3
FRONT SUSPENSION, SPECIAL TOOLS .....2-3
FRONT WHEEL SPEED SENSOR - INSTALLATION ........................ 5-92
FRONT WHEEL SPEED SENSOR - REMOVAL ........................... 5-91
FRONT WHEELHOUSE SPLASH SHIELD - INSTALLATION ....................... 23-57
FRONT WHEELHOUSE SPLASH SHIELD - REMOVAL .......................... 23-57
FRONT WIPER ARM ALIGNMENT - STANDARD PROCEDURE ...............8R-9
FRONT WIPER ARMS - INSTALLATION ....8R-9
FRONT WIPER ARMS - REMOVAL ........8R-9
FRONT WIPER MOTOR - INSTALLATION . . 8R-10
FRONT WIPER MOTOR - REMOVAL .......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS AND TESTING ........................ 8R-2
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

TUBE - REMOVAL, DRAIN.............23-172
TUBE - REMOVAL, EXHAUST ..........24-116
TUBE - REMOVAL, FUEL TANK FILLER ....14-16
TUBES AND HOSES - DESCRIPTION, BRAKE .............................. 5-14
TUBES AND HOSES - INSPECTION, BRAKE .............................. 5-14
TUBES AND HOSES - OPERATION, BRAKE .............................. 5-14
TUBES, INSTALLATION - FRONT HEATER CORE .............................. 24-85
TUBES, INSTALLATION - UNDERBODY HEATER ........................... 24-112
TUBES, REMOVAL - FRONT HEATER CORE .............................. 24-84
TUBES, REMOVAL - UNDERBODY HEATER ........................... 24-109
TUBING AND FITTINGS, STANDARD PROCEDURE - HANDLING ..............24-69
TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE KEY
LOCK .............................. 23-90
TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK ............23-90
TURN SIGNAL SYSTEM - DESCRIPTION . . . 8L-17
TURN SIGNAL SYSTEM - OPERATION ....8L-17
UNDER SEAT STORAGE BIN - INSTALLATION ...................... 23-149
UNDER SEAT STORAGE BIN - REMOVAL . 23-149
UNDER SEAT STORAGE BIN GUIDE - INSTALLATION ...................... 23-150
UNDER SEAT STORAGE BIN GUIDE - REMOVAL ......................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - INSTALLATION .................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - REMOVAL ........................ 23-150
UNDERBODY HEATER TUBES, INSTALLATION ...................... 24-112
UNDERBODY HEATER TUBES, REMOVAL . 24-109
UNDERBODY LINES - DESCRIPTION .....24-108
UNDERBODY LINES - OPERATION ......24-108
UNDERBODY REFRIGERANT LINES, INSTALLATION ...................... 24-112
UNDERBODY REFRIGERANT LINES, REMOVAL ......................... 24-110
UNIT - DESCRIPTION, LOWER DRIVE ....8N-53
UNIT - EXPORT - INSTALLATION, HEADLAMP ......................... 8L-17
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-17
UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - INSTALLATION, HEADLAMP .......8L-15
UNIT - INSTALLATION, HEATER ........24-122
UNIT - INSTALLATION, LOWER DRIVE ....8N-54
UNIT - INSTALLATION, TAIL LAMP .......8L-19
UNIT - OPERATION, LOWER DRIVE ......8N-53
UNIT - REMOVAL, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - REMOVAL, HEADLAMP ..........8L-15
UNIT - REMOVAL, HEATER ............24-121
UNIT - REMOVAL, LOWER DRIVE .......8N-53
UNIT - REMOVAL, TAIL LAMP ...........8L-19
UNIT / SENSOR - DESCRIPTION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - INSTALLATION, FUEL LEVEL SENDING ...................... 14-6
UNIT / SENSOR - OPERATION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - REMOVAL, FUEL LEVEL SENDING ...................... 14-5
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG
LAMP ............................... 8L-9
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP ....8L-15
UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP .........8L-9
UNIT ALIGNMENT - STANDARD PROCEDURE, HEADLAMP ..............8L-14
UNIT FLUID - DESCRIPTION, AWD POWER TRANSFER .....................0-6
UNIT TRACK & RACK - DESCRIPTION, LOWER DRIVE ...................... 8N-57
UNIT TRACK & RACK - INSTALLATION, LOWER DRIVE ...................... 8N-58
UNIT TRACK & RACK - OPERATION, LOWER DRIVE ...................... 8N-57UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE ...................... 8N-57
UNIVERSAL TRANSMITTER - DESCRIPTION ....................... 8M-11
UNIVERSAL TRANSMITTER, DIAGNOSIS AND TESTING ....................... 8M-11
UPPER - INSPECTION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, SHROUD .......19-22
UPPER - REMOVAL, INTAKE MANIFOLD ....9-60
UPPER - REMOVAL, SHROUD ...........19-22
UPPER HINGE - INSTALLATION .........23-36
UPPER HINGE - REMOVAL .............23-36
UPPER INTAKE MANIFOLD - INSTALLATION ....................... 9-149
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-148
UPPER RADIATOR CROSSMEMBER - INSTALLATION ....................... 23-56
UPPER RADIATOR CROSSMEMBER - REMOVAL .......................... 23-56
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-80
UPPER TRIM - REMOVAL, B-PILLAR .....23-80
UPSTREAM 1/1 - 2.4L - INSTALLATION . . . 14-38
UPSTREAM 1/1 - 2.4L - REMOVAL .......14-37
UPSTREAM 1/1 - 3.3/3.8L - INSTALLATION ....................... 14-39
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL ....14-38
USE WIRING DIAGRAMS - DESCRIPTION, HOW TO .............8W-01-1
USING PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING
CLEARANCE ..................... 9-12,9-86
VAC LEAK DETECTION ASSY - INSTALLATION, NATURAL ..............25-14
VAC LEAK DETECTION ASSY - REMOVAL, NATURAL .................. 25-14
VACUUM PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD ........9-148
VACUUM RESERVOIR - DESCRIPTION .....8P-6
VACUUM RESERVOIR - INSTALLATION ....8P-6
VACUUM RESERVOIR - OPERATION .......8P-6
VACUUM RESERVOIR - REMOVAL ........8P-6
VALVE - DESCRIPTION ................25-23
VALVE - DESCRIPTION, A/C EXPANSION . 24-100
VALVE - DESCRIPTION, EXPANSION ......24-81
VALVE - DESCRIPTION, PCV ............25-18
VALVE - INSTALLATION, OIL PRESSURE RELIEF ............................. 9-144
VALVE - OPERATION ..................25-23
VALVE - OPERATION, A/C EXPANSION . . . 24-100
VALVE - OPERATION, EXPANSION .......24-81
VALVE - OPERATION, PCV ..............25-18
VALVE - REMOVAL, OIL PRESSURE RELIEF ............................. 9-143
VALVE BODY - ASSEMBLY ......21-139,21-291
VALVE BODY - DESCRIPTION ....21-132,21-283
VALVE BODY - DISASSEMBLY ....21-135,21-286
VALVE BODY - INSTALLATION ....21-144,21-295
VALVE BODY - OPERATION ......21-132,21-283
VALVE BODY - REMOVAL .......21-133,21-284
VALVE CORE - DESCRIPTION, SERVICE PORT.............................. 24-95
VALVE CORE - INSTALLATION, SERVICE PORT.............................. 24-95
VALVE CORE - REMOVAL, SERVICE PORT.............................. 24-95
VALVE, DESCRIPTION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE, DIAGNOSIS AND TESTING - FRONT A/C EXPANSION ...............24-82
VALVE, DIAGNOSIS AND TESTING - REAR A/C EXPANSION ...............24-101
VALVE (HEIGHT SENSING) - DESCRIPTION, PROPORTIONING .........5-53
VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING, PROPORTIONING .........5-54
VALVE (HEIGHT SENSING) - INSTALLATION, PROPORTIONING .........5-55
VALVE (HEIGHT SENSING) - OPERATION, PROPORTIONING ..................... 5-53
VALVE (HEIGHT SENSING) - REMOVAL, PROPORTIONING ..................... 5-55
VALVE, OPERATION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE SEATS - STANDARD PROCEDURE, REFACING VALVES ................... 9-107VALVE SPRINGS - DESCRIPTION
........9-109
VALVE SPRINGS - OPERATION ..........9-109
VALVE STEM SEALS - DESCRIPTION .....9-114
VALVE STEM SEALS - INSTALLATION .....9-115
VALVE STEM SEALS - REMOVAL ........9-115
VALVE TIMING VERIFICATION - STANDARD PROCEDURE ...............9-155
VALVES - OPERATION, HYDRAULIC CIRCUITS ............................ 5-95
VALVES & SEATS - CLEANING, INTAKE/EXHAUST ................ 9-108,9-33
VALVES & SEATS - DESCRIPTION, INTAKE/EXHAUST ................ 9-107,9-33
VALVES & SEATS - INSPECTION, INTAKE/EXHAUST .................... 9-108
VALVES & SEATS - INSTALLATION, INTAKE/EXHAUST .................... 9-109
VALVES & SEATS - OPERATION, INTAKE/EXHAUST .................... 9-107
VALVES & SEATS - REMOVAL, INTAKE/EXHAUST .................... 9-108
VALVES AND VALVE SEATS - STANDARD PROCEDURE, REFACING ...............9-107
VANITY LAMP - INSTALLATION .........8L-24
VANITY LAMP - REMOVAL .............8L-24
VAPOR CANISTER - DESCRIPTION .......25-19
VAPOR CANISTER - OPERATION .........25-19
VARIABLE BRAKE PROPORTIONING - DESCRIPTION, ELECTRONIC .............5-88
VARIABLE BRAKE PROPORTIONING - OPERATION, ELECTRONIC ................5-89
VARIATION ADJUSTMENT, STANDARD PROCEDURE - COMPASS ...............8M-5
VEHICLE DOES NOT FILL - DIAGNOSIS AND TESTING ....................... 25-17
VEHICLE EMISSION CONTROL INFORMATION LABEL, DESCRIPTION ......25-1
VEHICLE IDENTIFICATION - DESCRIPTION ........................ 23-1
VEHICLE INFO CENTER - DESCRIPTION, ELECTRONIC ........................ 8M-7
VEHICLE INFO CENTER - OPERATION, ELECTRONIC ........................ 8M-7
VEHICLE INFORMATION CENTER, DIAGNOSIS AND TESTING -
ELECTRONIC ........................ 8M-8
VEHICLE INFORMATION CENTER PROGRAMMING, STANDARD
PROCEDURE - ELECTRONIC ............8M-8
VEHICLE THEFT SECURITY - DESCRIPTION ........................ 8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
VENT WINDOW MOTOR, DIAGNOSIS AND TESTING ....................... 8N-62
VERIFICATION - STANDARD PROCEDURE, VALVE TIMING ...........9-155
VIBRATION - DIAGNOSIS AND TESTING, TIRE AND WHEEL ..................... 22-1
VIBRATION DAMPER - INSTALLATION ....9-132,
9-49
VIBRATION DAMPER - REMOVAL ....9-132,9-48
VIDEO SCREEN - DESCRIPTION .........8A-20
VIDEO SCREEN - INSTALLATION ........8A-20
VIDEO SCREEN - OPERATION ...........8A-20
VIDEO SCREEN - REMOVAL ............8A-20
VIEW MIRROR - INSTALLATION, REAR . . . 23-97
VIEW MIRROR - INSTALLATION, SIDE ....23-60
VIEW MIRROR - REMOVAL, REAR .......23-97
VIEW MIRROR - REMOVAL, SIDE ........23-60
VISOR - INSTALLATION, SUN ...........23-99
VISOR - REMOVAL, SUN ...............23-99
VISOR SUPPORT - INSTALLATION, SUN . . . 23-99
VISOR SUPPORT - REMOVAL, SUN ......23-99
VOLT SUPPLY - PCM OUTPUT - OPERATION, 5 ....................... 8E-15
VOLTAGE DROP - STANDARD PROCEDURE, TESTING FOR A .......8W-01-10
VOLTAGE POTENTIAL - STANDARD PROCEDURE, TESTING OF ...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION ....8F-30
VOLTAGE REGULATOR - OPERATION .....8F-30
VOLTAGE TEST, STANDARD PROCEDURE - OPEN-CIRCUIT ..................... 8F-13
VTSS/SKIS INDICATOR LAMP - DESCRIPTION ........................ 8Q-8
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

VTSS/SKIS INDICATOR LAMP -OPERATION .......................... 8Q-8
WARNING - A/C SYSTEM ..............24-66
WARNING - ENGINE COOLING SYSTEM . . . 24-65
WARNING - INSTALLATION ............23-162
WARNING - INSTALLATION .............19-16
WARNING - REMOVAL ...............23-161
WARNING - REMOVAL ................19-11
WARNING - SAFETY PRECAUTIONS AND WARNINGS .......................... 23-1
WARNING - WARNINGS ................8O-5
WARNING - WARNINGS AND CAUTIONS . . 19-10, 19-26
WARNING - WINDSHIELD SAFETY PRECAUTIONS ...................... 23-161
WARNING, CHIME/BUZZER ..............8B-2
WARNING, DESCRIPTION ................5-4
WARNING, DESCRIPTION ..............19-37
WARNING, LAMPS/LIGHTING - EXTERIOR ........................... 8L-3
WARNING, OPERATION ...............24-114
WARNINGS AND CAUTIONS, WARNING . . 19-10, 19-26
WARNINGS, GENERAL ..............8W-01-7
WARNINGS, WARNING .................8O-5
WARNINGS, WARNING - SAFETY PRECAUTIONS ........................ 23-1
WASHER FLUID LEVEL SWITCH - INSTALLATION ...................... 8R-11
WASHER FLUID LEVEL SWITCH - REMOVAL .......................... 8R-11
WASHER HOSES - INSTALLATION .......8R-12
WASHER HOSES - REMOVAL ...........8R-11
WASHER PUMP MOTOR - INSTALLATION . 8R-12
WASHER PUMP MOTOR - REMOVAL .....8R-12
WASHER RESERVOIR - INSTALLATION . . . 8R-13
WASHER RESERVOIR - REMOVAL .......8R-12
WASHER SYSTEM - DIAGNOSIS AND TESTING ............................ 8R-5
WATER CHANNEL - INSTALLATION ......23-174
WATER CHANNEL - REMOVAL .........23-174
WATER LEAKS, DIAGNOSIS AND TESTING ............................ 23-1
WATER PUMP - 2.4L - CLEANING ........7-32
WATER PUMP - 2.4L - DESCRIPTION ......7-32
WATER PUMP - 2.4L - INSPECTION .......7-32
WATER PUMP - 2.4L - INSTALLATION .....7-32
WATER PUMP - 2.4L - REMOVAL .........7-32
WATER PUMP - 3.3/3.8L - CLEANING .....7-35
WATER PUMP - 3.3/3.8L - DESCRIPTION . . . 7-34
WATER PUMP - 3.3/3.8L - INSPECTION ....7-35
WATER PUMP - 3.3/3.8L - INSTALLATION ........................ 7-35
WATER PUMP - 3.3/3.8L - REMOVAL ......7-34
WATER PUMP INLET TUBE - 2.4L - DESCRIPTION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - INSTALLATION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - REMOVAL ........................... 7-36
WATER PUMP INLET TUBE - 3.3/3.8L - INSTALLATION ........................ 7-37
WATER PUMP INLET TUBE - 3.3/3.8L - REMOVAL ........................... 7-37
WATERSHIELD - INSTALLATION .........23-21
WATERSHIELD - REMOVAL .............23-21
WEAR - STANDARD PROCEDURE, MEASURING TIMING CHAIN ............9-155
WEAR INDICATORS - DIAGNOSIS AND TESTING, TREAD ..................... 22-16
WEAR PATTERNS - DIAGNOSIS AND TESTING, TIRE ...................... 22-16
WEATHERSTRIP - INSTALLATION, FRONT DOOR ............................ 23-168
WEATHERSTRIP - INSTALLATION, FRONT DOOR GLASS RUN .................. 23-166
WEATHERSTRIP - INSTALLATION, SLIDING DOOR ..................... 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR ............................ 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR GLASS RUN .................. 23-166WEATHERSTRIP - REMOVAL, SLIDING
DOOR ............................ 23-168
WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION, SEAT .........8O-43
WEIGHT BLADDER & PRESSURE SENSOR - OPERATION, SEAT ...........8O-44
WELD LOCATIONS - FOLD-IN-FLOOR - SPECIFICATIONS .................... 23-350
WELD LOCATIONS - SPECIFICATIONS . . . 23-234
WHEEL - DESCRIPTION ...............22-18
WHEEL - INSPECTION, TONE ............5-94
WHEEL - INSTALLATION, STEERING ......19-24
WHEEL - REMOVAL, STEERING .........19-23
WHEEL ALIGNMENT - DESCRIPTION ......2-47
WHEEL ALIGNMENT - STANDARD PROCEDURE ......................... 2-52
WHEEL ALIGNMENT, SPECIFICATIONS .....2-56
WHEEL AND WHEEL TRIM CARE, CLEANING .......................... 22-19
WHEEL ASSEMBLY (ALUMINUM WHEEL) - INSTALLATION, TIRE .................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL) - REMOVAL, TIRE ..................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - INSTALLATION, TIRE ................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - REMOVAL, TIRE ...................... 22-8
WHEEL BALANCE - STANDARD PROCEDURE, TIRE .................... 22-5
WHEEL COVER - DESCRIPTION .........22-19
WHEEL COVER - INSTALLATION ..........22-20
WHEEL COVER - REMOVAL ............22-19
WHEEL CYLINDERS - INSPECTION ........5-62
WHEEL CYLINDERS - INSTALLATION ......5-62
WHEEL CYLINDERS - REMOVAL ..........5-62
WHEEL INSPECTION - DIAGNOSIS AND TESTING ........................... 22-19
WHEEL MATCH MOUNTING - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL MOUNTING STUDS - FRONT - INSTALLATION ....................... 22-21
WHEEL MOUNTING STUDS - FRONT - REMOVAL .......................... 22-21
WHEEL MOUNTING STUDS - REAR - INSTALLATION ....................... 22-22
WHEEL MOUNTING STUDS - REAR - REMOVAL .......................... 22-22
WHEEL ROTATION - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL RUNOUT, SPECIFICATIONS - TONE ............................... 5-91
WHEEL, SPECIFICATIONS ..............22-19
WHEEL SPEED SENSOR - AWD - INSTALLATION, REAR .................. 5-92
WHEEL SPEED SENSOR - AWD - REMOVAL, REAR ...................... 5-92
WHEEL SPEED SENSOR - FWD - INSTALLATION, REAR .................. 5-93
WHEEL SPEED SENSOR - FWD - REMOVAL, REAR ...................... 5-93
WHEEL SPEED SENSOR - INSTALLATION, FRONT .................5-92
WHEEL SPEED SENSOR - REMOVAL, FRONT .............................. 5-91
WHEEL SPEED SENSOR AIR GAP, SPECIFICATIONS ...................... 5-91
WHEEL TRIM CARE, CLEANING - WHEEL . . 22-19
WHEEL VIBRATION - DIAGNOSIS AND TESTING, TIRE ....................... 22-1
WHEELHOUSE SPLASH SHIELD - INSTALLATION, FRONT ................23-57
WHEELHOUSE SPLASH SHIELD - REMOVAL, FRONT .................... 23-57
WIND DEFLECTOR - INSTALLATION .....23-174
WIND DEFLECTOR - REMOVAL .........23-174
WIND NOISE, DIAGNOSIS AND TESTING . . . 23-2
WINDOW - INSTALLATION, QUARTER . . . 23-164
WINDOW - REMOVAL, QUARTER .......23-164
WINDOW CRANK - INSTALLATION .......23-21
WINDOW CRANK - REMOVAL ...........23-21
WINDOW DEFOGGER RELAY - DESCRIPTION, REAR .................. 8G-3WINDOW DEFOGGER RELAY -
INSTALLATION, REAR .................. 8G-4
WINDOW DEFOGGER RELAY - OPERATION, REAR .................... 8G-3
WINDOW DEFOGGER RELAY - REMOVAL, REAR ..................... 8G-4
WINDOW DEFOGGER SWITCH - DESCRIPTION, REAR .................. 8G-4
WINDOW DEFOGGER SWITCH - OPERATION, REAR .................... 8G-4
WINDOW MOTOR - REMOVAL ..........8N-62
WINDOW MOTOR, DIAGNOSIS AND TESTING - VENT ..................... 8N-62
WINDOW REGULATOR - MANUAL - INSTALLATION ....................... 23-23
WINDOW REGULATOR - MANUAL - REMOVAL .......................... 23-22
WINDOW REGULATOR - POWER - INSTALLATION ....................... 23-22
WINDOW REGULATOR - POWER - REMOVAL .......................... 23-22
WINDOW SWITCH, DIAGNOSIS AND TESTING ........................... 8N-63
WINDOWS - DESCRIPTION, POWER .....8N-61
WINDOWS - OPERATION, POWER .......8N-61
WINDOWS, DIAGNOSIS AND TESTING - POWER ............................ 8N-61
WINDSHIELD - DESCRIPTION ..........23-161
WINDSHIELD SAFETY PRECAUTIONS, WARNING ......................... 23-161
WIPER ARM - INSTALLATION, REAR .....8R-10
WIPER ARM - REMOVAL, REAR ..........8R-10
WIPER ARM ALIGNMENT - STANDARD PROCEDURE, FRONT .................. 8R-9
WIPER ARMS - INSTALLATION, FRONT ....8R-9
WIPER ARMS - REMOVAL, FRONT ........8R-9
WIPER BLADES - CLEANING ...........8R-13
WIPER BLADES - INSTALLATION ........8R-13
WIPER BLADES - REMOVAL ............8R-13
WIPER LINKAGE - INSTALLATION .......8R-14
WIPER LINKAGE - REMOVAL ...........8R-13
WIPER MODULE - INSTALLATION .......8R-14
WIPER MODULE - REMOVAL ...........8R-14
WIPER MOTOR - INSTALLATION, FRONT . . 8R-10
WIPER MOTOR - INSTALLATION, REAR . . . 8R-10
WIPER MOTOR - REMOVAL, FRONT ......8R-9
WIPER MOTOR - REMOVAL, REAR ......8R-10
WIPER SYSTEM - DIAGNOSIS AND TESTING, FRONT ..................... 8R-2
WIPER SYSTEM - DIAGNOSIS AND TESTING, REAR ...................... 8R-4
WIPERS/WASHERS - DESCRIPTION .......8R-1
WIPERS/WASHERS - OPERATION ........8R-2
WIPER/WASHER SWITCH - DESCRIPTION, REAR .................8R-10
WIPER/WASHER SWITCH - DIAGNOSIS AND TESTING, FRONT .................8R-2
WIPER/WASHER SWITCH - OPERATION, REAR .............................. 8R-11
WIRE SPLICING - STANDARD PROCEDURE .....................8W -01-15
WIRING - INSTALLATION, HEATER ......24-122
WIRING - REMOVAL, HEATER ..........24-122
WIRING DIAGRAMS - DESCRIPTION, HOW TO USE .....................8W -01-1
WIRING HARNESS - DESCRIPTION ......8N-59
WIRING HARNESS - DIAGNOSIS AND TESTING .........................8W -01-7
WIRING HARNESS - INSTALLATION ......8N-59
WIRING HARNESS - OPERATION ........8N-59
WIRING HARNESS - REMOVAL .........8N-59
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD PROCEDURE, REPAIR OF DAMAGED
OR............................. 9-10,9-88
ZONE, DESCRIPTION - MANUAL DUAL .....24-2
ZONE, DESCRIPTION - MANUAL SINGLE . . . 24-2
ZONE, DESCRIPTION - MANUAL THREE ....24-2
ZONE, OPERATION - MANUAL DUAL ......24-5
ZONE, OPERATION - MANUAL SINGLE .....24-4
ZONE, OPERATION - MANUAL THREE .....24-5
RS INDEX35
Description Group-Page Description Group-Page Description Group-Page