2005 CHRYSLER CARAVAN brakes

(3) Align the engine compartment ends of both
heater core tubes with the openings in the dash
panel seal and push them simultaneously forward
through the seal far enough to engage the heater
core ends of the tubes with the heater core supply
and return ports.
(4) Position both heater core tubes and the sealing
plate simultaneously to the heater core supply and
return ports.
NOTE: The heater core tubes each have a slot that
must be indexed to a location tab within each of the
heater core ports. Adjust the position of the tubes
as required so that the sealing plate fits flush
against the heater core supply and return ports,
which indicates that the tubes are properly indexed.
(5) Index both heater core tubes to the heater core
ports.
(6) Install the screw that secures the heater core
tube sealing plate to the heater core supply and
return ports. Tighten the screw to 3 N´m (27 in. lbs.).
(7) Install the silencer under the driver side end of
the instrument panel.
(8) Connect the heater hoses to the heater hose
tubes (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING/HEATER INLET HOSE - INSTAL-
LATION) and(Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING/HEATER RETURN
HOSE - INSTALLATION).
(9) Reconnect the battery negative cable.
(10) Refill the engine cooling system (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM REFILL).
FRONT HEATER CORE
(1) While pushing the brake pedal downward and
pulling the accelerator pedal upward far enough for
clearance, slide the heater core into the distribution
housing.
(2) Install the two screws that secure the heater
core mounting plate to the distribution housing.
Tighten the screws to 2 N´m (17 in. lbs.).(3) Install the heater core tubes (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING/
HEATER CORE - INSTALLATION).
(4) Reconnect the power brake booster input rod
(push rod) to the pin on the brake pedal arm (Refer
to 5 - BRAKES/HYDRAULIC/MECHANICAL/
POWER BRAKE BOOSTER - INSTALLATION).
(5) Reinstall the brake lamp switch into its mount-
ing bracket (Refer to 8 - ELECTRICAL/LAMPS/
LIGHTING - EXTERIOR/BRAKE LAMP SWITCH -
INSTALLATION).
(6) Reinstall the silencer boot around the base of
the lower steering shaft on the dash panel.
(7) Reconnect the battery negative cable.
(8) Refill the engine cooling system (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM REFILL).
(9) Operate system for two thermostat cycles to
assure the elimination of any air that may be
trapped within the cooling system.
HEATER INLET HOSE
REMOVAL
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
WARNING).
NOTE: The heater inlet hose is constructed from
formed steel tubing and rubber hoses. Depending
on application, the ends are secured to the heater
core, engine oil cooler or the engine by spring ten-
sion clamps.
(1) Drain the engine cooling system (Refer to 7 -
COOLING - STANDARD PROCEDURE - COOLING
SYSTEM DRAIN).
24 - 86 PLUMBING - FRONTRS
HEATER CORE (Continued)

BACKLIGHT (EBL) SYSTEM, DIAGNOSISAND TESTING - ELECTRIC ..............8G-2
BACKSTOW STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-158
BACKSTOW STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-158
BAG RETAINER - INSTALLATION, PLASTIC GROCERY .................. 23-149
BAG RETAINER - REMOVAL, PLASTIC GROCERY ......................... 23-149
BALANCE - STANDARD PROCEDURE, TIRE AND WHEEL ..................... 22-5
BALANCE SHAFTS AND CARRIER ASSEMBLY - DESCRIPTION .............9-71
BALANCE SHAFTS AND CARRIER ASSEMBLY - INSTALLATION .............9-73
BALANCE SHAFTS AND CARRIER ASSEMBLY - OPERATION ...............9-71
BALANCE SHAFTS AND CARRIER ASSEMBLY - REMOVAL .................9-71
BALL JOINT - DESCRIPTION, LOWER ......2-10
BALL JOINT - DIAGNOSIS AND TESTING, LOWER ............................. 2-10
BALL JOINT - OPERATION, LOWER .......2-10
BAR - DESCRIPTION, STABILIZER ....2-16,2-44
BAR - DESCRIPTION, TRACK ............2-45
BAR - INSPECTION, STABILIZER ..........2-17
BAR - INSTALLATION, STABILIZER ........2-17
BAR - INSTALLATION, TRACK ............2-46
BAR - OPERATION, STABILIZER ......2-16,2-44
BAR - OPERATION, TRACK ................2-46
BAR - REMOVAL, STABILIZER ...........2-17
BAR - REMOVAL, TRACK ...............2-46
BAR CUSHION - INSTALLATION, STABILIZER ...........................2-4
BAR CUSHION - REMOVAL, STABILIZER ....2-4
BASE BRAKE BLEEDING - STANDARD PROCEDURE ..........................5-8
BASE BRAKE SYSTEM - DIAGNOSIS AND TESTING .............................5-4
BASE BRAKE SYSTEM, SPECIAL TOOLS ....5-10
BASE BRAKES - DESCRIPTION ............5-3
BASE BRAKES - OPERATION ..............5-3
BASE BRAKES (EXPORT) - DESCRIPTION . . . 5-3
BASE COAT/CLEARCOAT FINISH - DESCRIPTION ...................... 23-101
BASE RISER - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-135
BASE RISER - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-134
BASE TRAY - INSTALLATION, FLOOR CONSOLE ........................... 23-89
BASE TRAY - REMOVAL, FLOOR CONSOLE ........................... 23-89
BATTERY - DESCRIPTION ...............8F-7
BATTERY - OPERATION .................8F-9
BATTERY - REMOVAL .................8F-16
BATTERY - SPECIFICATIONS ............8N-24
BATTERY CABLES - DESCRIPTION .......8F-16
BATTERY CABLES - OPERATION .........8F-17
BATTERY CABLES, DIAGNOSIS AND TESTING ........................... 8F-17
BATTERY CHARGING, STANDARD PROCEDURE - CONVENTIONAL ..........8F-11
BATTERY CHARGING, STANDARD PROCEDURE - SPIRAL PLATE ...........8F-10
BATTERY, DIAGNOSIS AND TESTING ......8F-9
BATTERY ELECTROLYTE LEVEL, STANDARD PROCEDURE - CHECKING ....8F-14
BATTERY HOLDDOWN - INSTALLATION . . . 8F-16
BATTERY HOLDDOWN - REMOVAL .......8F-16
BATTERY REPLACEMENT - STANDARD PROCEDURE ........................ 8N-24
BATTERY, SPECIFICATIONS ..............8F-6
BATTERY SYSTEM - DESCRIPTION ........8F-1
BATTERY SYSTEM - OPERATION .........8F-2
BATTERY SYSTEM, DIAGNOSIS AND TESTING ............................ 8F-2
BATTERY SYSTEM SPECIAL TOOLS, SPECIAL TOOLS ...................... 8F-7
BATTERY TEMPERATURE SENSOR - DESCRIPTION ....................... 8F-24
BATTERY TEMPERATURE SENSOR - OPERATION ......................... 8F-24
BATTERY TEMPERATURE SENSOR - REMOVAL .......................... 8F-24
BATTERY TEMPERATURE SENSOR - SPECIFICATIONS ..................... 8F-23BATTERY TESTER, STANDARD
PROCEDURE - MICRO 420 .............8F-15
BATTERY TRAY - DESCRIPTION .........8F-19
BATTERY TRAY - INSTALLATION .........8F-20
BATTERY TRAY - REMOVAL ............8F-19
BEARING - DESCRIPTION, HUB .......2-30,2-5
BEARING - DIAGNOSIS AND TESTING, HUB............................. 2-31,2-5
BEARING - INSTALLATION, HUB .......2-33,2-5
BEARING - OPERATION, HUB .........2-30,2-5
BEARING - REMOVAL, HUB ..........2-31,2-5
BEARING CLEARANCE - STANDARD PROCEDURE, MEASURING
CONNECTING ROD ................... 9-123
BEARING CLEARANCE USING PLASTIGAGE - STANDARD
PROCEDURE, MEASURING ..........9-12,9-86
BEARING FITTING - STANDARD PROCEDURE, MAIN ................... 9-125
BEARING PRELOAD - ADJUSTMENT, DIFFERENTIAL ...................... 21-228
BEARING PRELOAD MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL ....................... 21-79
BEARINGS - INSTALLATION, CRANKSHAFT MAIN .................. 9-127
BEARINGS - REMOVAL, CRANKSHAFT MAIN .............................. 9-127
BEARINGS (IN BLOCK) - DESCRIPTION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - INSPECTION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - INSTALLATION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - OPERATION, CAMSHAFT ......................... 9-118
BEARINGS (IN BLOCK) - REMOVAL, CAMSHAFT ......................... 9-118
BELLCRANK - INSTALLATION ...........23-35
BELLCRANK - REMOVAL ...............23-35
BELT - DIAGNOSIS AND TESTING, ACCESSORY DRIVE .....................7-7
BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER LAP ..............23-157
BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER LAP ..............23-157
BELT - INSTALLATION, TIMING ...........9-67
BELT - REMOVAL, TIMING ..............9-65
BELT & RETRACTOR - FIRST ROW - OUTBOARD - INSTALLATION, SEAT ......8O-40
BELT & RETRACTOR - FIRST ROW - OUTBOARD - REMOVAL, SEAT ..........8O-39
BELT & RETRACTOR - OUTBOARD - FRONT - INSTALLATION, SEAT ..........8O-39
BELT & RETRACTOR - OUTBOARD - FRONT - REMOVAL, SEAT ..............8O-38
BELT & RETRACTOR - SECOND ROW - LEFT OUTBOARD - INSTALLATION,
SEAT .............................. 8O-42
BELT & RETRACTOR - SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT .....8O-42
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD - INSTALLATION,
SEAT .............................. 8O-40
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT ....8O-40
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC -
LWB - INSTALLATION, SEAT ............8O-41
BELT & RETRACTOR - SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC -
LWB - REMOVAL, SEAT ...............8O-41
BELT BUCKLE - FIRST ROW - BENCH - INSTALLATION, SEAT .................8O-37
BELT BUCKLE - FIRST ROW - BENCH - REMOVAL, SEAT ..................... 8O-36
BELT BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT ....8O-36
BELT BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT .......8O-35
BELT BUCKLE - FRONT INBOARD - INSTALLATION, SEAT .................8O-35
BELT BUCKLE - FRONT INBOARD - REMOVAL, SEAT ..................... 8O-35
BELT BUCKLE - SECOND ROW - THREE PASSENGER BENCH - INSTALLATION,
SEAT .............................. 8O-40BELT BUCKLE - SECOND ROW - THREE
PASSENGER BENCH - REMOVAL, SEAT . . . 8O-40
BELT BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT . . . 8O-38
BELT BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT .......8O-37
BELT CENTER LAP BELT - FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-157
BELT CENTER LAP BELT - FOLD-IN- FLOOR - REMOVAL, SEAT .............23-157
BELT COVER(S) - INSTALLATION, TIMING ............................. 9-64
BELT COVER(S) - REMOVAL, TIMING ......9-63
BELT HEIGHT ADJUSTE R-BOR
C-PILLAR - INSTALLATION, SEAT ........8O-38
BELT HEIGHT ADJUSTE R-BOR
C-PILLAR - REMOVAL, SEAT ...........8O-38
BELT HEIGHT ADJUSTER KNOB - INSTALLATION, SEAT .................8O-38
BELT HEIGHT ADJUSTER KNOB - REMOVAL, SEAT ..................... 8O-38
BELT MOLDING - INSTALLATION, FRONT DOOR INNER ....................... 23-168
BELT MOLDING - INSTALLATION, FRONT DOOR OUTER ...................... 23-167
BELT MOLDING - REMOVAL, FRONT DOOR INNER ....................... 23-168
BELT MOLDING - REMOVAL, FRONT DOOR OUTER ...................... 23-167
BELT TENSION - STANDARD PROCEDURE, CHECKING POWER
STEERING ............................7-8
BELT TENSION SENSOR - DESCRIPTION . . . 8O-8
BELT TENSION SENSOR - OPERATION .....8O-9
BELT TENSION, SPECIFICATIONS - ACCESSORY DRIVE .....................7-5
BELT TENSIONER - 2.4L - INSTALLATION . . 7-11
BELT TENSIONER - 2.4L - REMOVAL ......7-11
BELT TENSIONER - 3.3/3.8L - INSTALLATION ........................ 7-12
BELT TENSIONER - 3.3/3.8L - REMOVAL . . . 7-12
BELT TENSIONER - DESCRIPTION, SEAT . . 8O-43
BELT TENSIONER - OPERATION, SEAT ....8O-43
BELT TENSIONER & PULLEY - INSTALLATION, TIMING .................9-70
BELT TENSIONER & PULLEY - REMOVAL, TIMING .................... 9-69
BELTS - 2.4L - ADJUSTMENTS, DRIVE .....7-10
BELTS - 2.4L - INSTALLATION, DRIVE ......7-9
BELTS - 2.4L - REMOVAL, DRIVE ..........7-9
BELTS - 3.3/3.8L - INSTALLATION, DRIVE . . 7-12
BELTS - 3.3/3.8L - REMOVAL, DRIVE ......7-11
BELTS - CLEANING, DRIVE ...............7-8
BELTS - INSPECTION, DRIVE .............7-8
BENCH - INSTALLATION, SEAT BACK HINGE COVERS - QUAD BUCKET, 50/50
SPLIT ............................. 23-146
BENCH - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW ................8O-37
BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW - THREE
PASSENGER ........................ 8O-40
BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW INBOARD -
50/50 .............................. 8O-38
BENCH - INSTALLATION, SEAT CUSHION COVER - QUAD BUCKET, 50/50 SPLIT . . . 23-144
BENCH - REMOVAL, SEAT BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT . . 23-146
BENCH - REMOVAL, SEAT BELT BUCKLE - FIRST ROW ....................... 8O-36
BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW - THREE PASSENGER ....8O-40
BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW INBOARD - 50/50 .......8O-37
BENCH - REMOVAL, SEAT CUSHION COVER - QUAD BUCKET, 50/50 SPLIT . . . 23-144
BENCH SEAT - REMOVAL, CHILD SEAT MODULE .......................... 23-104
BENCH SEAT BACK - INSTALLATION .....23-147
BENCH SEAT BACK - REMOVAL ........23-147
BENCH SEAT BACK COVER - INSTALLATION ...................... 23-148
BENCH SEAT BACK COVER - REMOVAL . . 23-148
BENCH SEAT BACK HINGE - REMOVAL . . 23-146
BENCH SEAT BACK PANEL - INSTALLATION ...................... 23-144
BENCH SEAT BACK PANEL - REMOVAL . . 23-143
RS INDEX3
Description Group-Page Description Group-Page Description Group-Page

BRAKE CABLES - ADJUSTMENT,PARKING ............................ 5-65
BRAKE CALIPER - INSTALLATION, REAR DISC ............................... 5-30
BRAKE CALIPER - REMOVAL, REAR DISC ............................... 5-28
BRAKE CALIPER ADAPTER - INSTALLATION, FRONT DISC .............5-31
BRAKE CALIPER ADAPTER - REMOVAL, FRONT DISC ......................... 5-31
BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT
DISC ............................... 5-27
BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC .......5-24
BRAKE CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION, DISC .........5-32
BRAKE CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL, DISC .............5-31
BRAKE CALIPER (TRW BRAKES) - INSTALLATION, FRONT DISC .............5-27
BRAKE CALIPER (TRW BRAKES) - REMOVAL, FRONT DISC ................5-24
BRAKE FASTENER TORQUE, SPECIFICATIONS .......................5-9
BRAKE FLUID CONTAMINATION - DIAGNOSIS AND TESTING ..............5-33
BRAKE FLUID LEVEL CHECKING - STANDARD PROCEDURE ................5-33
BRAKE FLUID LEVEL SWITCH - DESCRIPTION ........................ 5-10
BRAKE FLUID LEVEL SWITCH - INSTALLATION ........................ 5-11
BRAKE FLUID LEVEL SWITCH - OPERATION .......................... 5-10
BRAKE FLUID LEVEL SWITCH - REMOVAL ........................... 5-11
BRAKE FLUID, SPECIFICATIONS ..........5-33
BRAKE INTERMEDIATE - INSTALLATION, CABLE - PARKING ..................... 5-69
BRAKE INTERMEDIATE - REMOVAL, CABLE - PARKING ..................... 5-69
BRAKE LAMP SWITCH - DESCRIPTION ....8L-4
BRAKE LAMP SWITCH - DIAGNOSIS AND TESTING ........................ 8L-4
BRAKE LAMP SWITCH - INSTALLATION ....8L-5
BRAKE LAMP SWITCH - OPERATION ......8L-4
BRAKE LAMP SWITCH - REMOVAL .......8L-5
BRAKE LEVER AND FRONT CABLE - INSTALLATION, PARKING ...............5-77
BRAKE LEVER AND FRONT CABLE - REMOVAL, PARKING ................... 5-77
BRAKE PROPORTIONING - DESCRIPTION, ELECTRONIC VARIABLE ....5-88
BRAKE PROPORTIONING - OPERATION, ELECTRONIC VARIABLE ................5-89
BRAKE ROTOR - DIAGNOSIS AND TESTING ............................ 5-55
BRAKE ROTOR - INSTALLATION, FRONT . . . 5-59
BRAKE ROTOR - REMOVAL, FRONT .......5-59
BRAKE ROTOR, EXPORT ................5-60
BRAKE ROTOR MACHINING - STANDARD PROCEDURE ......................... 5-58
BRAKE ROTOR, SPECIFICATIONS .........5-60
BRAKE SHOE LINING - INSPECTION, REAR DRUM ......................... 5-22
BRAKE SHOES - ADJUSTMENT, PARKING . . 5-85
BRAKE SHOES - ADJUSTMENT, REAR DRUM .............................. 5-23
BRAKE SHOES - CLEANING, DISC ....5-16,5-18
BRAKE SHOES - INSPECTION, DISC . . . 5-16,5-18
BRAKE SHOES - INSTALLATION, REAR DISC ............................... 5-19
BRAKE SHOES - INSTALLATION, REAR DRUM .............................. 5-22
BRAKE SHOES - REMOVAL, REAR DISC ....5-17
BRAKE SHOES - REMOVAL, REAR DRUM . . 5-19
BRAKE SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT
DISC ............................... 5-16
BRAKE SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC .......5-15
BRAKE SHOES (TRW BRAKES) - INSTALLATION, FRONT DISC .............5-17
BRAKE SHOES (TRW BRAKES) - REMOVAL, FRONT DISC ................5-15
BRAKE SYSTEM - DESCRIPTION, ANTILOCK ........................... 5-87BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE ........................5-4
BRAKE SYSTEM - OPERATION, ANTILOCK ........................... 5-88
BRAKE SYSTEM BLEEDING - STANDARD PROCEDURE, ANTILOCK ................5-90
BRAKE SYSTEM (EXPORT) - DESCRIPTION, ANTILOCK ...............5-87
BRAKE SYSTEM, SPECIAL TOOLS - BASE . . 5-10
BRAKE TUBES AND HOSES - DESCRIPTION ........................ 5-14
BRAKE TUBES AND HOSES - INSPECTION ......................... 5-14
BRAKE TUBES AND HOSES - OPERATION . . 5-14
BRAKES - DESCRIPTION, BASE ...........5-3
BRAKES - OPERATION, BASE .............5-3
BRAKES (EXPORT) - DESCRIPTION, BASE ................................5-3
BRAKES (EXPORT) - DESCRIPTION, DISC . . 5-13
BRAKES (FRONT) - DESCRIPTION, DISC . . . 5-11
BRAKES (FRONT) - OPERATION, DISC .....5-13
BRAKES (REAR) - DESCRIPTION, DISC ....5-13
BRAKES (REAR) - DESCRIPTION, DRUM . . . 5-13
BRAKES (REAR) - OPERATION, DISC ......5-14
BRAKE/TRANSMISSION SHIFT INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING ................ 21-115,21-266
BREAK-IN, STANDARD PROCEDURE - A/C CLUTCH ........................ 24-15
BUCKET - INSTALLATION, BUCKET SEAT BACK - QUAD ........................ 23-141
BUCKET - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW INBOARD -
QUAD ............................. 8O-36
BUCKET - REMOVAL, BUCKET SEAT BACK - QUAD ...................... 23-140
BUCKET - REMOVAL, SEAT BELT BUCKLE - FIRST ROW INBOARD - QUAD .........8O-35
BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT BACK HINGE
COVERS - QUAD .................... 23-146
BUCKET, 50/50 SPLIT, BENCH - INSTALLATION, SEAT CUSHION COVER
- QUAD ........................... 23-144
BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK HINGE COVERS
- QUAD ........................... 23-146
BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT CUSHION COVER -
QUAD ............................. 23-144
BUCKET SEAT BACK - QUAD BUCKET - INSTALLATION ...................... 23-141
BUCKET SEAT BACK - QUAD BUCKET - REMOVAL ......................... 23-140
BUCKET SEAT RISER - INSTALLATION, QUAD ............................. 23-143
BUCKET SEAT RISER - REMOVAL, QUAD . 23-143
BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - INSTALLATION, QUAD .......23-143
BUCKET SEAT SIDE SHIELD - NO CUP HOLDER - REMOVAL, QUAD ...........23-143
BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - INSTALLATION, QUAD .....23-151
BUCKET SEAT SIDE SHIELD/CUP HOLDER - FLAP AND SPRING
ASSEMBLY - REMOVAL, QUAD .........23-151
BUCKET SEAT SIDE SHIELD/CUP HOLDER - INSTALLATION, QUAD .......23-142
BUCKET SEAT SIDE SHIELD/CUP HOLDER - REMOVAL, QUAD ...........23-141
BUCKLE - FIRST ROW - BENCH - INSTALLATION, SEAT BELT .............8O-37
BUCKLE - FIRST ROW - BENCH - REMOVAL, SEAT BELT ................8O-36
BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT ....8O-36
BUCKLE - FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT ........8O-35
BUCKLE - FRONT INBOARD - INSTALLATION, SEAT BELT .............8O-35
BUCKLE - FRONT INBOARD - REMOVAL, SEAT BELT ......................... 8O-35
BUCKLE - SECOND ROW - THREE PASSENGER BENCH - INSTALLATION,
SEAT BELT ......................... 8O-40BUCKLE - SECOND ROW - THREE
PASSENGER BENCH - REMOVAL, SEAT
BELT .............................. 8O-40
BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT
BELT .............................. 8O-38
BUCKLE - SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT ....8O-37
BUMPER - DESCRIPTION, JOUNCE ........2-35
BUMPER - INSTALLATION, STOP ........23-25
BUMPER - OPERATION, JOUNCE .........2-35
BUMPER - REMOVAL, STOP ............23-25
BUMPER BEZEL - INSTALLATION, SLIDING DOOR STOP .................23-25
BUMPER BEZEL - REMOVAL, SLIDING DOOR STOP ........................ 23-25
BUMPER REINFORCEMENT - INSTALLATION, FRONT .................13-3
BUMPER REINFORCEMENT - INSTALLATION, REAR .................. 13-5
BUMPER REINFORCEMENT - REMOVAL, FRONT .............................. 13-3
BUMPER REINFORCEMENT - REMOVAL, REAR ............................... 13-5
BUS COMMUNICATION RECEIVE - PCM INPUT - OPERATION, DATA .............8E-14
BUS, OPERATION - PROGRAMMABLE COMMUNICATIONS INTERFACE (PCI) .....14-25
BUSHING - LEAF SPRING FRONT - INSTALLATION ........................ 2-30
BUSHING - LEAF SPRING FRONT - REMOVAL ........................... 2-29
BUSHINGS - INSTALLATION, FRONT CROSSMEMBER MOUNT ...............13-17
BUSHINGS - REMOVAL, FRONT CROSSMEMBER MOUNT ...............13-17
BUSHINGS (CONTINENTAL TEVES BRAKES) - ASSEMBLY, CALIPER GUIDE
PIN ................................ 5-25
BUSHINGS (CONTINENTAL TEVES BRAKES) - DISASSEMBLY, CALIPER
GUIDE PIN ........................... 5-24
CABIN HEATER - DESCRIPTION ........24-113
CABIN HEATER, DIAGNOSIS AND TESTING - SUPPLEMENTAL ...........24-114
CABLE - DESCRIPTION .................8P-4
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-7
CABLE - DESCRIPTION, SPARK PLUG .....8I-10
CABLE - INSTALLATION ................8P-4
CABLE - INSTALLATION, GEAR SHIFT ....21-234
CABLE - INSTALLATION, HOLD OPEN LATCH ............................. 23-38
CABLE - INSTALLATION, INSIDE HANDLE . . 23-38
CABLE - INSTALLATION, INSTRUMENT PANEL ANTENNA ..................... 8A-12
CABLE - INSTALLATION, LATCH RELEASE . 23-64
CABLE - INSTALLATION, OUTSIDE HANDLE ............................ 23-37
CABLE - INSTALLATION, PARKING BRAKE LEVER AND FRONT ..............5-77
CABLE - INSTALLATION, THROTTLE CONTROL .......................... 14-40
CABLE - OPERATION ................... 8P-4
CABLE - OPERATION, ANTENNA BODY .....8A-7
CABLE - PARKING BRAKE INTERMEDIATE - INSTALLATION ..........5-69
CABLE - PARKING BRAKE INTERMEDIATE - REMOVAL .............5-69
CABLE - REMOVAL .................... 8P-4
CABLE - REMOVAL, GEAR SHIFT . . 21-233,21-84
CABLE - REMOVAL, HOLD OPEN LATCH . . . 23-38
CABLE - REMOVAL, INSIDE HANDLE .....23-37
CABLE - REMOVAL, INSTRUMENT PANEL ANTENNA .......................... 8A-12
CABLE - REMOVAL, LATCH RELEASE .....23-63
CABLE - REMOVAL, OUTSIDE HANDLE ....23-37
CABLE - REMOVAL, PARKING BRAKE LEVER AND FRONT .................... 5-77
CABLE - REMOVAL, THROTTLE CONTROL .......................... 14-40
CABLE ADJUSTMENT, ADJUSTMENTS - GEARSHIFT ........................ 21-235
CABLE ADJUSTMENT, INSTALLATION - SYNCHRONIZING ..............23-105,23-147
CABLE, DIAGNOSIS AND TESTING - ANTENNA BODY ...................... 8A-8
RS INDEX5
Description Group-Page Description Group-Page Description Group-Page

CABLE END CLEANING ANDLUBRICATION - STANDARD
PROCEDURE ......................... 5-65
CABLE RESISTANCE, SPECIFICATIONS - SPARK PLUG ......................... 8I-2
CABLES - ADJUSTMENT, PARKING BRAKE .............................. 5-65
CABLES - DESCRIPTION, BATTERY .......8F-16
CABLES - OPERATION, BATTERY ........8F-17
CABLES, DIAGNOSIS AND TESTING - BATTERY ........................... 8F-17
CALIBRATION, STANDARD PROCEDURE - A/C-HEATER CONTROL ................24-19
CALIBRATION, STANDARD PROCEDURE - COMPASS ........................... 8M-4
CALIPER - CLEANING ..............5-25,5-29
CALIPER - INSPECTION ............5-25,5-29
CALIPER - INSTALLATION, REAR DISC BRAKE .............................. 5-30
CALIPER - REMOVAL, REAR DISC BRAKE .............................. 5-28
CALIPER ADAPTER - INSTALLATION, FRONT DISC BRAKE ................... 5-31
CALIPER ADAPTER - REMOVAL, FRONT DISC BRAKE ......................... 5-31
CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT
DISC BRAKE ......................... 5-27
CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC
BRAKE .............................. 5-24
CALIPER GUIDE PIN BUSHINGS (CONTINENTAL TEVES BRAKES) -
ASSEMBLY ............................ 5-25
CALIPER GUIDE PIN BUSHINGS (CONTINENTAL TEVES BRAKES) -
DISASSEMBLY ........................ 5-24
CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION, DISC BRAKE ............5-32
CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL, DISC BRAKE ................5-31
CALIPER PISTON AND SEAL - ASSEMBLY ...................... 5-26,5-30
CALIPER PISTON AND SEAL - DISASSEMBLY .................... 5-24,5-28
CALIPER (TRW BRAKES) - INSTALLATION, FRONT DISC BRAKE ......5-27
CALIPER (TRW BRAKES) - REMOVAL, FRONT DISC BRAKE ................... 5-24
CAMSHAFT & BEARINGS (IN BLOCK) - DESCRIPTION ....................... 9-118
CAMSHAFT & BEARINGS (IN BLOCK) - INSPECTION ........................ 9-118
CAMSHAFT & BEARINGS (IN BLOCK) - INSTALLATION ....................... 9-118
CAMSHAFT & BEARINGS (IN BLOCK) - OPERATION ......................... 9-118
CAMSHAFT & BEARINGS (IN BLOCK) - REMOVAL .......................... 9-118
CAMSHAFT END PLAY - STANDARD PROCEDURE, MEASURING ..............9-29
CAMSHAFT OIL SEAL(S) - INSTALLATION . . 9-29
CAMSHAFT OIL SEAL(S) - REMOVAL ......9-28
CAMSHAFT POSITION SENSOR - DESCRIPTION ......................... 8I-4
CAMSHAFT POSITION SENSOR - OPERATION .......................... 8I-4
CAMSHAFT SPROCKET - INSTALLATION, TIMING CHAIN ....................... 9-160
CAMSHAFT SPROCKET - REMOVAL, TIMING CHAIN ....................... 9-159
CAMSHAFT SPROCKETS - INSTALLATION . . 9-67
CAMSHAFT SPROCKETS - REMOVAL ......9-66
CAMSHAFT(S) - CLEANING ..............9-30
CAMSHAFT(S) - DESCRIPTION ...........9-29
CAMSHAFT(S) - INSPECTION ............9-30
CAMSHAFT(S) - INSTALLATION ..........9-31
CAMSHAFT(S) - OPERATION .............9-29
CAMSHAFT(S) - REMOVAL ..............9-30
CANISTER - DESCRIPTION, VAPOR ......25-19
CANISTER - INSTALLATION, REAR EVAP . . 25-21
CANISTER - OPERATION, VAPOR ........25-19
CANISTER - REMOVAL, REAR EVAP ......25-20
CAP - DESCRIPTION, FUEL FILLER .......25-13
CAP - DESCRIPTION, RADIATOR PRESSURE .......................... 7-27
CAP - INSTALLATION, INSTRUMENT PANEL RIGHT END ................... 23-72CAP - OPERATION, FUEL FILLER
........25-13
CAP - OPERATION, RADIATOR PRESSURE .......................... 7-27
CAP - REMOVAL, INSTRUMENT PANEL RIGHT END ......................... 23-72
CAP TESTING - DIAGNOSIS AND TESTING, COOLING SYSTEM
PRESSURE .......................... 7-28
CAP TO FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR .....7-28
CAPACITIES - SPECIFICATIONS, FLUID ......0-6
CARE, CLEANING - WHEEL AND WHEEL TRIM .............................. 22-19
CARGO - INSTALLATION, AWD, HEAVY DUTY ............................... 2-36
CARGO - INSTALLATION, SPRING ........2-40
CARGO - REMOVAL, AWD, HEAVY DUTY . . . 2-36
CARGO - REMOVAL, SPRING ............2-40
CARPET INSERT - FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR
TUB ............................... 23-98
CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB ....23-98
CARPET TRIM RING AND COVER - FOLD-IN-FLOOR - INSTALLATION ........23-84
CARPET TRIM RING AND COVER - FOLD-IN-FLOOR - REMOVAL ............23-84
CARPETS - FOLD-IN-FLOOR - INSTALLATION ....................... 23-83
CARPETS - FOLD-IN-FLOOR - REMOVAL . . 23-82
CARPETS AND FLOOR MATS - INSTALLATION ....................... 23-81
CARPETS AND FLOOR MATS - REMOVAL . 23-81
CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB .......23-96
CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB ...........23-95
CARRIER ASSEMBLY - DESCRIPTION, BALANCE SHAFTS ..................... 9-71
CARRIER ASSEMBLY - INSTALLATION, BALANCE SHAFTS ..................... 9-73
CARRIER ASSEMBLY - OPERATION, BALANCE SHAFTS ..................... 9-71
CARRIER ASSEMBLY - REMOVAL, BALANCE SHAFTS ..................... 9-71
CATALYTIC CONVERTER - DESCRIPTION . . . 11-4
CATALYTIC CONVERTER - INSPECTION ....11-6
CATALYTIC CONVERTER - INSTALLATION . . . 11-6
CATALYTIC CONVERTER - OPERATION .....11-4
CATALYTIC CONVERTER - REMOVAL ......11-5
CAUTION, A/C SYSTEM ................24-66
CAUTION, DESCRIPTION .................5-4
CAUTION, DESCRIPTION ...............19-37
CAUTION, OPERATION .................5-90
CAUTION, SENSOR - TPM ..............22-11
CAUTIONS, WARNING - WARNINGS . 19-10,19-26
CD CHANGER - DESCRIPTION ..........8A-11
CD CHANGER - INSTALLATION ..........8A-11
CD CHANGER - OPERATION ............8A-11
CD CHANGER - REMOVAL .............8A-11
CENTER - DESCRIPTION, ELECTRONIC VEHICLE INFO ....................... 8M-7
CENTER - INSTALLATION, MESSAGE ......8M-1
CENTER - OPERATION, ELECTRONIC VEHICLE INFO ....................... 8M-7
CENTER - REMOVAL, MESSAGE .........8M-1
CENTER BEZEL - INSTALLATION, INSTRUMENT PANEL .................. 23-72
CENTER BEZEL - REMOVAL, INSTRUMENT PANEL .................. 23-71
CENTER BEZEL OUTLETS, INSTALLATION - FRONT ............................ 24-45
CENTER BEZEL OUTLETS, REMOVAL - FRONT ............................. 24-44
CENTER CONSOLE LAMP - INSTALLATION ....................... 8L-21
CENTER CONSOLE LAMP - REMOVAL ....8L-21
CENTER CONSOLE LAMP SWITCH - INSTALLATION ....................... 8L-21
CENTER CONSOLE LAMP SWITCH - REMOVAL .......................... 8L-21
CENTER, DIAGNOSIS AND TESTING - ELECTRONIC VEHICLE INFORMATION .....8M-8
CENTER HIGH MOUNTED STOP LAMP - INSTALLATION ........................ 8L-6
CENTER HIGH MOUNTED STOP LAMP - REMOVAL ........................... 8L-6CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION .................. 8L-6
CENTER HIGH MOUNTED STOP LAMP UNIT - REMOVAL ..................... 8L-6
CENTER HINGE - INSTALLATION .........23-24
CENTER HINGE - REMOVAL ............23-24
CENTER LAP BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT ............23-157
CENTER LAP BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT ................23-157
CENTER PROGRAMMING, STANDARD PROCEDURE - ELECTRONIC VEHICLE
INFORMATION ....................... 8M-8
CENTER STRIKER - INSTALLATION .......23-28
CENTER STRIKER - REMOVAL ..........23-28
CENTERING - STANDARD PROCEDURE, CLOCKSPRING ...................... 8O-11
CHAIN AND CAMSHAFT SPROCKET - INSTALLATION, TIMING ................9-160
CHAIN AND CAMSHAFT SPROCKET - REMOVAL, TIMING ................... 9-159
CHAIN COVER - INSTALLATION, TIMING . . 9-157
CHAIN COVER - REMOVAL, TIMING ......9-156
CHAIN WEAR - STANDARD PROCEDURE, MEASURING TIMING .................. 9-155
CHANGE - STANDARD PROCEDURE, ENGINE OIL AND FILTER ...........9-139,9-54
CHANGER - DESCRIPTION, CD ..........8A-11
CHANGER - INSTALLATION, CD .........8A-11
CHANGER - OPERATION, CD ............8A-11
CHANGER - REMOVAL, CD ..............8A-11
CHANNEL - INSTALLATION, WATER .....23-174
CHANNEL - REMOVAL, WATER .........23-174
CHARGE LEVEL TEST, DIAGNOSIS AND TESTING - SYSTEM ................... 24-67
CHARGE, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-71
CHARGING, STANDARD PROCEDURE - CONVENTIONAL BATTERY ..............8F-11
CHARGING, STANDARD PROCEDURE - SPIRAL PLATE BATTERY ...............8F-10
CHARGING SYSTEM - DESCRIPTION .....8F-21
CHARGING SYSTEM - OPERATION .......8F-21
CHARTS - DIAGNOSIS AND TESTING, STEERING SYSTEM DIAGNOSIS ..........19-3
CHARTS - SPECIFICATIONS, COLOR CODE ............................. 23-100
CHECK - DIAGNOSIS AND TESTING, COOLING SYSTEM FLOW ................7-3
CHECK - DIAGNOSIS AND TESTING, EXHAUST SYSTEM RESTRICTION .........11-2
CHECK - STANDARD PROCEDURE, COOLANT LEVEL .......................7-4
CHECK - STANDARD PROCEDURE, ENGINE OIL LEVEL ................... 9-140
CHECK, STANDARD PROCEDURE - ENGINE OIL LEVEL .................... 9-54
CHECK, STANDARD PROCEDURE - FLUID LEVEL AND CONDITION .........21-230,21-82
CHECK STRAP - INSTALLATION .........23-15
CHECK STRAP - REMOVAL .............23-15
CHECKING - STANDARD PROCEDURE, BRAKE FLUID LEVEL ................... 5-33
CHECKING - STANDARD PROCEDURE, POWER STEERING FLUID LEVEL ........19-44
CHECKING BATTERY ELECTROLYTE LEVEL, STANDARD PROCEDURE .........8F-14
CHECKING ENGINE OIL PRESSURE - DIAGNOSIS AND TESTING ..............9-53
CHECKING POWER STEERING BELT TENSION - STANDARD PROCEDURE .......7-8
CHILD RESTRAINT ANCHOR - DESCRIPTION ........................ 8O-9
CHILD RESTRAINT ANCHOR - OPERATION ......................... 8O-10
CHILD SEAT - INSTALLATION, QUAD ....23-106
CHILD SEAT - REMOVAL, QUAD ........23-106
CHILD SEAT MODULE, BENCH SEAT - REMOVAL ......................... 23-104
CHIME SYSTEM - DIAGNOSIS AND TESTING ............................ 8B-2
CHIME/BUZZER - DESCRIPTION ..........8B-1
CHIME/BUZZER - OPERATION ............8B-1
CHIME/BUZZER - WARNING .............8B-2
CHIME/THERMISTOR - DESCRIPTION .....8N-8
CHIME/THERMISTOR - INSTALLATION .....8N-9
CHIME/THERMISTOR - OPERATION .......8N-8
CHIME/THERMISTOR - REMOVAL ........8N-8
6 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

DEFOGGER RELAY - DESCRIPTION,REAR WINDOW ....................... 8G-3
DEFOGGER RELAY - INSTALLATION, REAR WINDOW ....................... 8G-4
DEFOGGER RELAY - OPERATION, REAR WINDOW ............................ 8G-3
DEFOGGER RELAY - REMOVAL, REAR WINDOW ............................ 8G-4
DEFOGGER SWITCH - DESCRIPTION, REAR WINDOW ....................... 8G-4
DEFOGGER SWITCH - OPERATION, REAR WINDOW ............................ 8G-4
DEFROSTER DUCT - INSTALLATION ......24-50
DEFROSTER DUCT - REMOVAL ..........24-49
DEMAGNETIZING, STANDARD PROCEDURE - COMPASS ...............8M-5
DEMISTER DUCTS - INSTALLATION, INSTRUMENT PANEL .................. 24-54
DEMISTER DUCTS - REMOVAL, INSTRUMENT PANEL .................. 24-54
DEMISTER OUTLETS, INSTALLATION - FRONT ............................. 24-45
DEMISTER OUTLETS, REMOVAL - FRONT . 24-44
DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER AN
AIRBAG ............................. 8O-7
DETECTION ASSY - INSTALLATION, NATURAL VAC LEAK .................. 25-14
DETECTION ASSY - REMOVAL, NATURAL VAC LEAK .......................... 25-14
DETECTION PUMP - INSTALLATION, LEAK .............................. 25-15
DETECTION PUMP - REMOVAL, LEAK ......25-15
DEVICES - STANDARD PROCEDURE, ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE ........................8W -01-8
DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING - ON-BOARD .................8F-22
DIAGNOSTIC TROUBLE CODES - STANDARD PROCEDURE, OBTAINING .....8E-15
DIAGRAMS - 4XTE TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS .................. 21-199,21-54
DIAGRAMS - DESCRIPTION, HOW TO USE WIRING ......................8W -01-1
DIAGRAMS - SPECIAL TOOLS, SCHEMATICS ........................ 21-68
DIESEL - DESCRIPTION ...............19-52
DIESEL - INSTALLATION ...............19-53
DIESEL - REMOVAL ................... 19-52
DIESEL ENGINE - DESCRIPTION, FUEL REQUIREMENTS .......................0-6
DIESEL ENGINES - DESCRIPTION, ENGINE OIL ...........................0-6
DIESEL ENGINES - EXPORT - DESCRIPTION ........................ 0-21
DIESEL ENGINES, INSTALLATION - 2.5L/2.8L ........................... 24-78
DIESEL ENGINES, REMOVAL - 2.5L/2.8L . . 24-77
DIFFERENTIAL BEARING PRELOAD - ADJUSTMENT ...................... 21-228
DIFFERENTIAL BEARING PRELOAD MEASUREMENT AND ADJUSTMENT,
ADJUSTMENTS ...................... 21-79
DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME ........13-11
DIMENSIONS - SPECIFICATIONS, BODY OPENING .......................... 23-180
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-6
DIODE - INSTALLATION ............8W-01-14
DIODE - REMOVAL ................8W -01-14
DISABLED INDICATOR - DESCRIPTION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - INSTALLATION, PASSENGER AIRBAG .................8O-34
DISABLED INDICATOR - OPERATION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - REMOVAL, PASSENGER AIRBAG .................8O-34
DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE, TRANSMISSION COOLER
LINE QUICK CONNECT FITTING ...........7-38
DISC BRAKE CALIPER - INSTALLATION, REAR ............................... 5-30
DISC BRAKE CALIPER - REMOVAL, REAR ............................... 5-28
DISC BRAKE CALIPER ADAPTER - INSTALLATION, FRONT .................5-31DISC BRAKE CALIPER ADAPTER -
REMOVAL, FRONT ..................... 5-31
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-27
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-24
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION ...............5-32
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL .................. 5-31
DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION, FRONT .................5-27
DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL, FRONT ..................... 5-24
DISC BRAKE SHOES - CLEANING .....5-16,5-18
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18
DISC BRAKE SHOES - INSTALLATION, REAR ............................... 5-19
DISC BRAKE SHOES - REMOVAL, REAR ....5-17
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-16
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-15
DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION, FRONT .................5-17
DISC BRAKE SHOES (TRW BRAKES) - REMOVAL, FRONT ..................... 5-15
DISC BRAKES (EXPORT) - DESCRIPTION . . . 5-13
DISC BRAKES (FRONT) - DESCRIPTION ....5-11
DISC BRAKES (FRONT) - OPERATION ......5-13
DISC BRAKES (REAR) - DESCRIPTION .....5-13
DISC BRAKES (REAR) - OPERATION ......5-14
DISCHARGE (ESD) SENSITIVE DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC ...................8W -01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-80
DISCHARGE LINE - REMOVAL, A/C .......24-79
DISPLAY - DESCRIPTION, PARK ASSIST . . . 8B-3
DISPLAY - INSTALLATION, PARK ASSIST . . . 8B-4
DISPLAY - OPERATION, PARK ASSIST .....8B-3
DISPLAY - REMOVAL, PARK ASSIST ......8B-4
DISPLAY TEST MODE, OPERATION - DRB III T STATE .......................... 25-10
DISSASEMBLY, REMOVAL ..............24-51
DISTRIBUTION DUCT - INSTALLATION ....24-57
DISTRIBUTION DUCT - REMOVAL ........24-57
DISTRIBUTION DUCTS - INSTALLATION, FLOOR ............................. 24-50
DISTRIBUTION DUCTS - REMOVAL, FLOOR ............................. 24-50
DISTRIBUTION SYSTEM - DESCRIPTION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEM - OPERATION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEMS, SPECIAL TOOLS - POWER ...................8W -97-1
DOES NOT FILL - DIAGNOSIS AND TESTING, VEHICLE ................... 25-17
DOME/CARGO LAMP - INSTALLATION ....8L-22
DOME/CARGO LAMP - REMOVAL ........8L-22
DOOR - INSTALLATION ................23-15
DOOR - INSTALLATION, FUEL FILL .......23-52
DOOR - INSTALLATION, SLIDING ........23-29
DOOR - REMOVAL .................... 23-15
DOOR - REMOVAL, FUEL FILL ..........23-52
DOOR - REMOVAL, SLIDING ............23-29
DOOR ACTUATOR - DESCRIPTION, BLEND ........................ 24-22,24-34
DOOR ACTUATOR - DESCRIPTION, MODE ............................. 24-29
DOOR ACTUATOR - DESCRIPTION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - INSTALLATION, BLEND ........................ 24-22,24-35
DOOR ACTUATOR - INSTALLATION, MODE ............................. 24-30
DOOR ACTUATOR - INSTALLATION, RECIRCULATION ..................... 24-32
DOOR ACTUATOR - OPERATION, BLEND . . 24-22,
24-35
DOOR ACTUATOR - OPERATION, MODE . . . 24-29
DOOR ACTUATOR - OPERATION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - REAR - DESCRIPTION, MODE .................24-39DOOR ACTUATOR - REAR -
INSTALLATION, MODE .................24-40
DOOR ACTUATOR - REAR - OPERATION, MODE ............................. 24-39
DOOR ACTUATOR - REAR - REMOVAL, MODE ............................. 24-39
DOOR ACTUATOR - REMOVAL, BLEND . . . 24-22, 24-35
DOOR ACTUATOR - REMOVAL, MODE ....24-29
DOOR ACTUATOR - REMOVAL, RECIRCULATION ..................... 24-32
DOOR ADJUSTMENT, STANDARD PROCEDURE - POWER SLIDING .........8N-49
DOOR ADJUSTMENTS, ADJUSTMENTS - SLIDING ............................ 23-30
DOOR BLOCKER LATCH - INSTALLATION, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH - REMOVAL, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL FILL .............23-53
DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL FILL .................23-53
DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL FILL .............23-54
DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL FILL .................23-54
DOOR CONTROL MODULE - DESCRIPTION, SLIDING ...............8E-18
DOOR CONTROL MODULE - OPERATION, SLIDING ............................ 8E-18
DOOR CONTROL MODULE, DIAGNOSIS AND TESTING - SLIDING ...............8E-18
DOOR CYLINDER LOCK SWITCH - EXPORT - DESCRIPTION ...............8N-22
DOOR CYLINDER LOCK SWITCH - EXPORT - OPERATION ................8N-22
DOOR CYLINDER LOCK SWITCH, EXPORT ............................ 8N-22
DOOR GLASS - INSTALLATION ..........23-17
DOOR GLASS - INSTALLATION, SLIDING . 23-163
DOOR GLASS - REMOVAL .............23-16
DOOR GLASS - REMOVAL, SLIDING .....23-163
DOOR GLASS RUN WEATHERSTRIP - INSTALLATION, FRONT ...............23-166
DOOR GLASS RUN WEATHERSTRIP - REMOVAL, FRONT ................... 23-166
DOOR INNER BELT MOLDING - INSTALLATION, FRONT ...............23-168
DOOR INNER BELT MOLDING - REMOVAL, FRONT ................... 23-168
DOOR LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING .........8N-48
DOOR LOCK MOTOR - INSTALLATION, SLIDING ........................... 8N-25
DOOR LOCK MOTOR - REMOVAL, SLIDING ........................... 8N-25
DOOR LOCK MOTOR, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR LOCK SWITCH, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR MOTOR - DESCRIPTION, SLIDING . . 8N-51
DOOR MOTOR - INSTALLATION, SLIDING . 8N-51
DOOR MOTOR - OPERATION, SLIDING . . . 8N-51
DOOR MOTOR - REMOVAL, SLIDING .....8N-51
DOOR OUTER BELT MOLDING - INSTALLATION, FRONT ...............23-167
DOOR OUTER BELT MOLDING - REMOVAL, FRONT ................... 23-167
DOOR SILL PLATE - INSTALLATION, SLIDING ............................ 23-99
DOOR SILL PLATE - REMOVAL, SLIDING . . 23-98
DOOR SILL TRIM PLATE - INSTALLATION ....................... 23-89
DOOR SILL TRIM PLATE - REMOVAL .....23-89
DOOR STOP BUMPER BEZEL - INSTALLATION, SLIDING ...............23-25
DOOR STOP BUMPER BEZEL - REMOVAL, SLIDING .................. 23-25
DOOR SYSTEM - DESCRIPTION, POWER SLIDING ........................... 8N-40
DOOR SYSTEM - OPERATION, POWER SLIDING ........................... 8N-41
DOOR SYSTEM, DIAGNOSIS AND TESTING - POWER SLIDING ............8N-42
DOOR WEATHERSTRIP - INSTALLATION, FRONT ............................ 23-168
10 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

DOOR WEATHERSTRIP - INSTALLATION,SLIDING ........................... 23-168
DOOR WEATHERSTRIP - REMOVAL, FRONT ............................ 23-168
DOOR WEATHERSTRIP - REMOVAL, SLIDING ........................... 23-168
DOSING PUMP - DESCRIPTION, FUEL . . . 24-117
DOSING PUMP - INSTALLATION, FUEL . . . 24-117
DOSING PUMP - OPERATION, FUEL .....24-117
DOSING PUMP - REMOVAL, FUEL ......24-117
DOWNSTREAM 1/2 - 2.4/3.3/3.8L - REMOVAL .......................... 14-38
DOWNSTREAM 2/1, 2.4/3.3/3.8L - INSTALLATION ....................... 14-39
D-PILLAR TRIM PANEL - INSTALLATION, LEFT .............................. 23-94
D-PILLAR TRIM PANEL - INSTALLATION, RIGHT ............................. 23-98
D-PILLAR TRIM PANEL - REMOVAL, LEFT .............................. 23-94
D-PILLAR TRIM PANEL - REMOVAL, RIGHT ............................. 23-97
DRAIN TUBE - INSTALLATION ..........23-172
DRAIN TUBE - REMOVAL .............23-172
DRAINCOCK - INSTALLATION, RADIATOR . . . 7-27
DRAINCOCK - REMOVAL, RADIATOR ......7-27
DRAINING - STANDARD PROCEDURE, COOLING SYSTEM .....................7-4
DRAINING FUEL TANK - STANDARD PROCEDURE ......................... 14-2
DRAW TEST, STANDARD PROCEDURE - IGNITION-OFF ....................... 8F-13
DRB III TSTATE DISPLAY TEST MODE,
OPERATION ......................... 25-10
DRIER - DESCRIPTION, RECEIVER .......24-92
DRIER - INSTALLATION, RECEIVER ......24-93
DRIER - OPERATION, RECEIVER .........24-92
DRIER - REMOVAL, RECEIVER ..........24-92
DRIVE - ASSEMBLY, FINAL .......21-224,21-78
DRIVE - DESCRIPTION, FINAL ....21-219,21-74
DRIVE - DESCRIPTION, FLEX ...........8N-55
DRIVE - DISASSEMBLY, FINAL ....21-220,21-75
DRIVE - INSTALLATION, FLEX ..........8N-56
DRIVE - OPERATION, FINAL ......21-220,21-75
DRIVE - OPERATION, FLEX .............8N-55
DRIVE - REMOVAL, FLEX ..............8N-55
DRIVE BELT - DIAGNOSIS AND TESTING, ACCESSORY ..........................7-7
DRIVE BELT TENSION, SPECIFICATIONS - ACCESSORY ..........................7-5
DRIVE BELTS - 2.4L - ADJUSTMENTS .....7-10
DRIVE BELTS - 2.4L - INSTALLATION .......7-9
DRIVE BELTS - 2.4L - REMOVAL ..........7-9
DRIVE BELTS - 3.3/3.8L - INSTALLATION . . . 7-12
DRIVE BELTS - 3.3/3.8L - REMOVAL ......7-11
DRIVE BELTS - CLEANING ...............7-8
DRIVE BELTS - INSPECTION ..............7-8
DRIVE UNIT - DESCRIPTION, LOWER ....8N-53
DRIVE UNIT - INSTALLATION, LOWER ....8N-54
DRIVE UNIT - OPERATION, LOWER ......8N-53
DRIVE UNIT - REMOVAL, LOWER .......8N-53
DRIVE UNIT TRACK & RACK - DESCRIPTION, LOWER ................8N-57
DRIVE UNIT TRACK & RACK - INSTALLATION, LOWER ...............8N-58
DRIVE UNIT TRACK & RACK - OPERATION, LOWER .................. 8N-57
DRIVE UNIT TRACK & RACK - REMOVAL, LOWER ................... 8N-57
DRIVELINE MODULE FLUIDS - DESCRIPTION, AWD REAR ...............0-6
DRIVER AIRBAG - DESCRIPTION ........8O-16
DRIVER AIRBAG - INSTALLATION .......8O-18
DRIVER AIRBAG - OPERATION ..........8O-16
DRIVER AIRBAG - REMOVAL ...........8O-17
DRIVER HEATED SEAT SWITCH, DIAGNOSIS AND TESTING ..............8G-9
DRIVER SEAT SWITCH, DIAGNOSIS AND TESTING ........................... 8N-34
DRIVING CLUTCHES - DESCRIPTION ....21-219,
21-74
DRIVING CLUTCHES - OPERATION . 21-219,21-74
DROP - STANDARD PROCEDURE, TESTING FOR A VOLTAGE ...........8W-01-10
DRUM - INSTALLATION .................5-32
DRUM - REMOVAL .................... 5-32
DRUM BRAKE - INSTALLATION, SUPPORT PLATE ...................... 5-61DRUM BRAKE - REMOVAL, SUPPORT
PLATE .............................. 5-61
DRUM BRAKE AUTOMATIC ADJUSTER - DIAGNOSIS AND TESTING ..............5-14
DRUM BRAKE SHOE LINING - INSPECTION, REAR .................... 5-22
DRUM BRAKE SHOES - ADJUSTMENT, REAR ............................... 5-23
DRUM BRAKE SHOES - INSTALLATION, REAR ............................... 5-22
DRUM BRAKE SHOES - REMOVAL, REAR . . 5-19
DRUM BRAKES (REAR) - DESCRIPTION ....5-13
DUAL ZONE, DESCRIPTION - MANUAL .....24-2
DUAL ZONE, OPERATION - MANUAL ......24-5
DUCT - INSTALLATION, DEFROSTER .....24-50
DUCT - INSTALLATION, DISTRIBUTION . . . 24-57
DUCT - INSTALLATION, REAR FLOOR HEAT .............................. 24-63
DUCT - REMOVAL, DEFROSTER .........24-49
DUCT - REMOVAL, DISTRIBUTION .......24-57
DUCT - REMOVAL, REAR FLOOR HEAT . . . 24-63
DUCTS - INSTALLATION, FLOOR DISTRIBUTION ....................... 24-50
DUCTS - INSTALLATION, INSTRUMENT PANEL ............................. 24-55
DUCTS - INSTALLATION, INSTRUMENT PANEL DEMISTER .................... 24-54
DUCTS - REMOVAL, FLOOR DISTRIBUTION ....................... 24-50
DUCTS - REMOVAL, INSTRUMENT PANEL .............................. 24-55
DUCTS - REMOVAL, INSTRUMENT PANEL DEMISTER .................... 24-54
DUTY, CARGO - INSTALLATION, AWD, HEAVY.............................. 2-36
DUTY, CARGO - REMOVAL, AWD, HEAVY . . . 2-36
DVD PLAYER - DESCRIPTION ...........8A-12
DVD PLAYER - INSTALLATION ..........8A-12
DVD PLAYER - REMOVAL ..............8A-12
ELECTRIC BACKLIGHT (EBL) SYSTEM, DIAGNOSIS AND TESTING ..............8G-2
ELECTROLYTE LEVEL, STANDARD PROCEDURE - CHECKING BATTERY ......8F-14
ELECTRONIC VARIABLE BRAKE PROPORTIONING - DESCRIPTION ........5-88
ELECTRONIC VARIABLE BRAKE PROPORTIONING - OPERATION ..........5-89
ELECTRONIC VEHICLE INFO CENTER - DESCRIPTION ........................ 8M-7
ELECTRONIC VEHICLE INFO CENTER - OPERATION ......................... 8M-7
ELECTRONIC VEHICLE INFORMATION CENTER, DIAGNOSIS AND TESTING ......8M-8
ELECTRONIC VEHICLE INFORMATION CENTER PROGRAMMING, STANDARD
PROCEDURE ......................... 8M-8
ELECTROSTATIC DISCHARGE (ESD) SENSITIVE DEVICES - STANDARD
PROCEDURE ......................8W -01-8
ELEMENT - INSTALLATION, AIR CLEANER ....................... 9-101,9-24
ELEMENT - REMOVAL, AIR CLEANER . 9-101,9-24
ELEMENTS - DESCRIPTION, HEATED SEAT .............................. 8G-11
ELEMENTS - OPERATION, HEATED SEAT . . 8G-11
ELEMENTS, DIAGNOSIS AND TESTING - HEATED SEAT ....................... 8G-11
EMISSION CONTROL INFORMATION LABEL, DESCRIPTION - VEHICLE .........25-1
END CAP - INSTALLATION, INSTRUMENT PANEL RIGHT ....................... 23-72
END CAP - REMOVAL, INSTRUMENT PANEL RIGHT ....................... 23-72
END CLEANING AND LUBRICATION - STANDARD PROCEDURE, CABLE .........5-65
END PLAY - STANDARD PROCEDURE, CRANKSHAFT ........................ 9-37
END PLAY - STANDARD PROCEDURE, MEASURING CAMSHAFT ................9-29
END PLAY - STANDARD PROCEDURE, MEASURING CRANKSHAFT .............9-128
ENGAGE ACTUATOR - DESCRIPTION ......8N-9
ENGAGE ACTUATOR - INSTALLATION .....8N-10
ENGAGE ACTUATOR - OPERATION ........8N-9
ENGAGE ACTUATOR - REMOVAL .........8N-9
ENGINE - A/C COMPRESSOR MOUNTING BRACKET, 2.4L ................. 24-74,24-75
ENGINE - CLEANING ................... 7-18ENGINE - DESCRIPTION, 2.4L/3.3L/3.8L . . . 19-52
ENGINE - DESCRIPTION, FUEL
REQUIREMENTS - DIESEL ...............0-6
ENGINE - INSPECTION .................7-18
ENGINE - INSTALLATION, 2.4L .....19-47,19-50,
19-51,19-53
ENGINE - INSTALLATION, 3.3L/3.8L . 19-48,19-50, 19-52,19-53
ENGINE - REMOVAL, 2.4L . . . 19-46,19-49,19-51, 19-52
ENGINE - REMOVAL, 3.3L/3.8L ....19-46,19-49,
19-51,19-52
ENGINE - SPECIFICATIONS, 2.4L .........9-16
ENGINE 2.4L - DESCRIPTION .............9-3
ENGINE 3.3/3.8L - DESCRIPTION .........9-78
ENGINE ASSEMBLY - INSTALLATION . . 9-14,9-91
ENGINE ASSEMBLY - REMOVAL ......9-12,9-88
ENGINE BLOCK - CLEANING ........9-115,9-37
ENGINE BLOCK - DESCRIPTION .....9-115,9-36
ENGINE BLOCK - INSPECTION ......9-115,9-37
ENGINE BLOCK HEATER - DESCRIPTION . . . 7-20
ENGINE BLOCK HEATER - INSTALLATION . . . 7-21
ENGINE BLOCK HEATER - OPERATION .....7-20
ENGINE BLOCK HEATER - REMOVAL ......7-21
ENGINE BLOCK HEATER TESTING - DIAGNOSIS AND TESTING ..............7-21
ENGINE COOLANT - DESCRIPTION ........7-19
ENGINE COOLANT - DESCRIPTION .........0-3
ENGINE COOLANT TEMPERATURE SENSOR - 2.4L - DESCRIPTION ..........7-21
ENGINE COOLANT TEMPERATURE SENSOR - 2.4L - INSTALLATION ..........7-21
ENGINE COOLANT TEMPERATURE SENSOR - 2.4L - REMOVAL .............7-21
ENGINE COOLANT TEMPERATURE SENSOR - 3.3/3.8L - DESCRIPTION .......7-21
ENGINE COOLANT TEMPERATURE SENSOR - 3.3/3.8L - INSTALLATION .......7-23
ENGINE COOLANT TEMPERATURE SENSOR - 3.3/3.8L - REMOVAL ..........7-21
ENGINE COOLANT THERMOSTAT - 2.4L - INSTALLATION ........................ 7-24
ENGINE COOLANT THERMOSTAT - 2.4L - REMOVAL ........................... 7-24
ENGINE COOLANT THERMOSTAT - 3.3/3.8L - INSTALLATION ...............7-25
ENGINE COOLANT THERMOSTAT - 3.3/3.8L - REMOVAL ................... 7-24
ENGINE COOLANT THERMOSTAT - DESCRIPTION ........................ 7-23
ENGINE COOLANT THERMOSTAT - DIAGNOSIS AND TESTING ..............7-23
ENGINE COOLANT THERMOSTAT - OPERATION .......................... 7-23
ENGINE COOLING SYSTEM - DIAGNOSIS AND TESTING ........................ 7-14
ENGINE COOLING SYSTEM REQUIREMENTS, DESCRIPTION ..........24-1
ENGINE COOLING SYSTEM, WARNING ....24-65
ENGINE CORE AND OIL GALLERY PLUGS - STANDARD PROCEDURE ..........9-10,9-88
ENGINE DIAGNOSIS - INTRODUCTION - DIAGNOSIS AND TESTING ...........9-3,9-78
ENGINE DIAGNOSIS - MECHANICAL - DIAGNOSIS AND TESTING ...........9-6,9-82
ENGINE DIAGNOSIS - PERFORMANCE - DIAGNOSIS AND TESTING ...........9-4,9-80
ENGINE GASKET SURFACE PREPARATION - STANDARD
PROCEDURE ..................... 9-11,9-87
ENGINE MOUNTING - DESCRIPTION . 9-134,9-50
ENGINE OIL - DESCRIPTION, FLEXIBLE FUEL ................................0-3
ENGINE OIL - DIESEL ENGINES - DESCRIPTION .........................0-6
ENGINE OIL AND FILTER CHANGE - STANDARD PROCEDURE ...........9-139,9-54
ENGINE OIL AND LUBRICANTS - DESCRIPTION .........................0-1
ENGINE OIL LEAK INSPECTION - DIAGNOSIS AND TESTING ...........9-8,9-84
ENGINE OIL LEVEL CHECK - STANDARD PROCEDURE ........................ 9-140
ENGINE OIL LEVEL CHECK, STANDARD PROCEDURE ......................... 9-54
ENGINE OIL PRESSURE - DIAGNOSIS AND TESTING ....................... 9-138
RS INDEX11
Description Group-Page Description Group-Page Description Group-Page

FOLD-IN-FLOOR - REMOVAL, SEATCUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT - SECOND ROW ...............23-138
FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD - SECOND ROW ................23-139
FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET INSERT .......23-98
FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - REMOVAL, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - SPECIFICATIONS, WELD LOCATIONS ................... 23-350
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY SEALING
LOCATIONS ........................ 23-209
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, STRUCTURAL
ADHESIVE LOCATIONS ...............23-228
FOLD-IN-FLOOR SEATING - INSTALLATION .................... 5-68,5-75
FOLD-IN-FLOOR SEATING - INSTALLATION, FWD ................... 2-45
FOLD-IN-FLOOR SEATING - REMOVAL . 5-66,5-72
FOLD-IN-FLOOR SEATING - REMOVAL, FWD................................ 2-45
FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS .....13-11
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FORWARD ............23-137
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FORWARD ................23-137
FORM-IN-PLACE GASKETS AND SEALERS, STANDARD PROCEDURE . . . 9-11,9-86
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FOLD ................23-160
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FOLD .................... 23-160
FRAME - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT BACK ....23-134
FRAME - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT BACK ........23-134
FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-157
FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-156
FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS .........13-11
FRAME DIMENSIONS - SPECIFICATIONS . . . 13-6
FREE MODULE - INSTALLATION, HANDS . . . 8T-3
FREE MODULE - REMOVAL, HANDS .......8T-3
FRONT - DESCRIPTION, HALF SHAFT .......3-1
FRONT - DESCRIPTION, PLUMBING ......24-65
FRONT - INSTALLATION, BUSHING - LEAF SPRING ........................ 2-30
FRONT - INSTALLATION, CRANKSHAFT OIL SEAL ....................... 9-130,9-42
FRONT - INSTALLATION, HALF SHAFT ......3-4
FRONT - INSTALLATION, SEAT BELT & RETRACTOR - OUTBOARD .............8O-39
FRONT - INSTALLATION, SPRING MOUNTS ............................ 2-43
FRONT - INSTALLATION, WHEEL MOUNTING STUDS ................... 22-21
FRONT - OPERATION, PLUMBING ........24-65
FRONT - REMOVAL, BUSHING - LEAF SPRING ............................. 2-29
FRONT - REMOVAL, CRANKSHAFT OIL SEAL .......................... 9-130,9-41
FRONT - REMOVAL, HALF SHAFT ..........3-2
FRONT - REMOVAL, SEAT BELT & RETRACTOR - OUTBOARD .............8O-38
FRONT - REMOVAL, SPRING MOUNTS .....2-42
FRONT - REMOVAL, WHEEL MOUNTING STUDS ............................. 22-21
FRONT - SPECIFICATIONS, HALF SHAFT ....3-6FRONT A/C EXPANSION VALVE,
DIAGNOSIS AND TESTING .............24-82
FRONT BLOWER MOTOR, DIAGNOSIS AND TESTING ....................... 24-46
FRONT BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING .......24-25
FRONT BRAKE ROTOR - INSTALLATION ....5-59
FRONT BRAKE ROTOR - REMOVAL .......5-59
FRONT BUMPER REINFORCEMENT - INSTALLATION ........................ 13-3
FRONT BUMPER REINFORCEMENT - REMOVAL ........................... 13-3
FRONT CABLE - INSTALLATION, PARKING BRAKE LEVER ................5-77
FRONT CABLE - REMOVAL, PARKING BRAKE LEVER ........................ 5-77
FRONT CENTER BEZEL OUTLETS, INSTALLATION ....................... 24-45
FRONT CENTER BEZEL OUTLETS, REMOVAL .......................... 24-44
FRONT CONTROL MODULE - DESCRIPTION ........................ 8E-7
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE, DIAGNOSIS AND TESTING ........................ 8E-7
FRONT CRADLE CROSSMEMBER - DESCRIPTION ....................... 13-14
FRONT CRADLE CROSSMEMBER THREAD REPAIR - DESCRIPTION ........13-14
FRONT CROSSMEMBER MOUNT BUSHINGS - INSTALLATION ............13-17
FRONT CROSSMEMBER MOUNT BUSHINGS - REMOVAL .................13-17
FRONT DEMISTER OUTLETS, INSTALLATION ....................... 24-45
FRONT DEMISTER OUTLETS, REMOVAL . . . 24-44
FRONT DISC BRAKE CALIPER ADAPTER - INSTALLATION ...................... 5-31
FRONT DISC BRAKE CALIPER ADAPTER - REMOVAL .......................... 5-31
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-27
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-24
FRONT DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION ...............5-27
FRONT DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL .................. 5-24
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-16
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-15
FRONT DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION ...............5-17
FRONT DISC BRAKE SHOES (TRW BRAKES) - REMOVAL .................. 5-15
FRONT DOOR GLASS RUN WEATHERSTRIP - INSTALLATION .......23-166
FRONT DOOR GLASS RUN WEATHERSTRIP - REMOVAL ...........23-166
FRONT DOOR INNER BELT MOLDING - INSTALLATION ...................... 23-168
FRONT DOOR INNER BELT MOLDING - REMOVAL ......................... 23-168
FRONT DOOR OUTER BELT MOLDING - INSTALLATION ...................... 23-167
FRONT DOOR OUTER BELT MOLDING - REMOVAL ......................... 23-167
FRONT DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
FRONT DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
FRONT FASCIA - INSTALLATION ..........13-1
FRONT FASCIA - REMOVAL ..............13-1
FRONT FENDER - INSTALLATION ........23-52
FRONT FENDER - REMOVAL ............23-51
FRONT FOG LAMP - DIAGNOSIS AND TESTING ............................ 8L-7
FRONT FOG LAMP - INSTALLATION .......8L-8
FRONT FOG LAMP - REMOVAL ...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .......8L-9
FRONT FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE ................8L-9FRONT HEATER CORE, INSTALLATION
....24-86
FRONT HEATER CORE, REMOVAL ........24-85
FRONT HEATER CORE TUBES, INSTALLATION ....................... 24-85
FRONT HEATER CORE TUBES, REMOVAL . . 24-84
FRONT INBOARD - INSTALLATION, SEAT BELT BUCKLE ....................... 8O-35
FRONT INBOARD - REMOVAL, SEAT BELT BUCKLE ....................... 8O-35
FRONT MOUNT - INSTALLATION ....9-134,9-50
FRONT MOUNT - REMOVAL ........9-134,9-50
FRONT SEAT - INSTALLATION ..........23-110
FRONT SEAT - REMOVAL .............23-108
FRONT SEAT BACK - INSTALLATION .....23-111
FRONT SEAT BACK - REMOVAL ........23-111
FRONT SEAT BACK ASSIST STRAP - INSTALLATION ...................... 23-112
FRONT SEAT BACK ASSIST STRAP - REMOVAL ......................... 23-112
FRONT SEAT BACK COVER - INSTALLATION ...................... 23-116
FRONT SEAT BACK COVER - REMOVAL . . 23-113
FRONT SEAT BACK PANEL - INSTALLATION ...................... 23-113
FRONT SEAT BACK PANEL - REMOVAL . . 23-112
FRONT SEAT CUSHION - INSTALLATION . . 23-118
FRONT SEAT CUSHION - OCS - INSTALLATION ...................... 23-120
FRONT SEAT CUSHION - OCS - REMOVAL ........................... 23-119
FRONT SEAT CUSHION - REMOVAL .....23-117
FRONT SEAT CUSHION SIDE COVER - INSTALLATION ...................... 23-121
FRONT SEAT CUSHION SIDE COVER - OCS - INSTALLATION ................23-122
FRONT SEAT CUSHION SIDE COVER - OCS - REMOVAL .................... 23-121
FRONT SEAT CUSHION SIDE COVER - REMOVAL ......................... 23-120
FRONT SEAT RISER - MANUAL - OCS - INSTALLATION ...................... 23-123
FRONT SEAT RISER - MANUAL - OCS - REMOVAL ......................... 23-123
FRONT SEAT TRACK - REAR COVER - INSTALLATION ...................... 23-128
FRONT SEAT TRACK - REAR COVER - REMOVAL ......................... 23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION ...............23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL ................... 23-126
FRONT SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION ...............23-125
FRONT SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL ................... 23-124
FRONT SEAT TRACK MANUAL ADJUSTER - INSTALLATION ...........23-126
FRONT SEAT TRACK MANUAL ADJUSTER - REMOVAL ...............23-125
FRONT SEAT TRACK POWER ADJUSTER - INSTALLATION .................... 23-124
FRONT SEAT TRACK POWER ADJUSTER - REMOVAL ........................ 23-124
FRONT SEAT TRACK REAR COVER - OCS - INSTALLATION .................... 23-129
FRONT SEAT TRACK REAR COVER - OCS - REMOVAL ........................ 23-129
FRONT SUSPENSION - DESCRIPTION ......2-2
FRONT SUSPENSION - OPERATION ........2-2
FRONT SUSPENSION FASTENER TORQUE, SPECIFICATIONS ...............2-3
FRONT SUSPENSION, SPECIAL TOOLS .....2-3
FRONT WHEEL SPEED SENSOR - INSTALLATION ........................ 5-92
FRONT WHEEL SPEED SENSOR - REMOVAL ........................... 5-91
FRONT WHEELHOUSE SPLASH SHIELD - INSTALLATION ....................... 23-57
FRONT WHEELHOUSE SPLASH SHIELD - REMOVAL .......................... 23-57
FRONT WIPER ARM ALIGNMENT - STANDARD PROCEDURE ...............8R-9
FRONT WIPER ARMS - INSTALLATION ....8R-9
FRONT WIPER ARMS - REMOVAL ........8R-9
FRONT WIPER MOTOR - INSTALLATION . . 8R-10
FRONT WIPER MOTOR - REMOVAL .......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS AND TESTING ........................ 8R-2
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FRONT WIPER/WASHER SWITCH -DIAGNOSIS AND TESTING ..............8R-2
FRONT-WHEEL-DRIVE - INSTALLATION ....2-36
FRONT-WHEEL-DRIVE - REMOVAL ........2-36
FUEL CORRECTION OR ADAPTIVE MEMORIES, OPERATION ...............14-24
FUEL DELIVERY SYSTEM - DIAGNOSIS AND TESTING ........................ 14-2
FUEL DOSING PUMP - DESCRIPTION ....24-117
FUEL DOSING PUMP - INSTALLATION . . . 24-117
FUEL DOSING PUMP - OPERATION .....24-117
FUEL DOSING PUMP - REMOVAL .......24-117
FUEL ENGINE OIL - DESCRIPTION, FLEXIBLE .............................0-3
FUEL FILL DOOR - INSTALLATION .......23-52
FUEL FILL DOOR - REMOVAL ...........23-52
FUEL FILL DOOR BLOCKER LATCH - INSTALLATION ....................... 23-53
FUEL FILL DOOR BLOCKER LATCH - REMOVAL .......................... 23-53
FUEL FILL DOOR BLOCKER LATCH STRIKER - INSTALLATION ..............23-53
FUEL FILL DOOR BLOCKER LATCH STRIKER - REMOVAL .................23-53
FUEL FILL DOOR BLOCKER LOCKOUT LINK - INSTALLATION .................23-54
FUEL FILL DOOR BLOCKER LOCKOUT LINK - REMOVAL ..................... 23-54
FUEL FILLER CAP - DESCRIPTION .......25-13
FUEL FILLER CAP - OPERATION .........25-13
FUEL INJECTOR - DESCRIPTION .........14-30
FUEL INJECTOR - OPERATION ..........14-31
FUEL LEVEL SENDING UNIT / SENSOR - DESCRIPTION ........................ 14-5
FUEL LEVEL SENDING UNIT / SENSOR - INSTALLATION ........................ 14-6
FUEL LEVEL SENDING UNIT / SENSOR - OPERATION .......................... 14-5
FUEL LEVEL SENDING UNIT / SENSOR - REMOVAL ........................... 14-5
FUEL LINES/HOSES AND CLAMPS - DESCRIPTION ........................ 14-7
FUEL PRESSURE GAUGE - STANDARD PROCEDURE ......................... 14-3
FUEL PRESSURE REGULATOR - INSTALLATION ........................ 14-7
FUEL PRESSURE REGULATOR - OPERATION .......................... 14-7
FUEL PRESSURE REGULATOR - REMOVAL ........................... 14-7
FUEL PUMP - DESCRIPTION .............14-8
FUEL PUMP - OPERATION ..............14-8
FUEL PUMP MODULE - DESCRIPTION .....14-8
FUEL PUMP MODULE - OPERATION .......14-9
FUEL PUMP RELAY - DESCRIPTION ......14-32
FUEL PUMP RELAY - OPERATION ........14-32
FUEL REQUIREMENTS - DESCRIPTION ......0-4
FUEL REQUIREMENTS - DIESEL ENGINE - DESCRIPTION ........................0-6
FUEL, SPECIAL TOOLS ............14-27,14-4
FUEL SYSTEM PRESSURE RELEASE PROCEDURE - STANDARD
PROCEDURE ......................... 14-2
FUEL SYSTEM PRESSURE, SPECIFICATIONS ...................... 14-4
FUEL TANK - DESCRIPTION ............14-12
FUEL TANK - OPERATION ..............14-12
FUEL TANK - STANDARD PROCEDURE, DRAINING ........................... 14-2
FUEL TANK FILLER TUBE - INSTALLATION ....................... 14-17
FUEL TANK FILLER TUBE - REMOVAL ....14-16
FULL OPEN SWITCH - DESCRIPTION ....8N-11,
8N-52
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD ...........8W-97-3
FUSE - OPERATION, IOD .............8W-97-3
FUSES POWERING SEVERAL LOADS - STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON ......8W-01-10
FWD - FOLD-IN-FLOOR SEATING - INSTALLATION ........................ 2-45
FWD - FOLD-IN-FLOOR SEATING - REMOVAL ........................... 2-45
FWD - INSTALLATION ..................2-45
FWD - INSTALLATION, REAR WHEEL SPEED SENSOR ....................... 5-93
FWD - INSTALLATION, SPRING ...........2-42FWD - REMOVAL
...................... 2-45
FWD - REMOVAL, REAR WHEEL SPEED SENSOR ............................ 5-93
FWD - REMOVAL, SPRING ..............2-40
GALLERY PLUGS - STANDARD PROCEDURE, ENGINE CORE AND OIL . 9-10,9-88
GAP AND FLUSH MEASUREMENTS - SPECIFICATIONS .................... 23-177
GAP, SPECIFICATIONS - WHEEL SPEED SENSOR AIR ......................... 5-91
GAS STRUT - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-139
GAS STRUT - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-138
GASKET - DIAGNOSIS AND TESTING, CYLINDER HEAD ................. 9-102,9-25
GASKET SURFACE PREPARATION - STANDARD PROCEDURE, ENGINE ....9-11,9-87
GASKETS AND SEALERS, STANDARD PROCEDURE - FORM-IN-PLACE ......9-11,9-86
GAUGE - STANDARD PROCEDURE, FUEL PRESSURE .......................... 14-3
GEAR - DESCRIPTION .................19-26
GEAR - INSTALLATION, LHD ............19-31
GEAR - INSTALLATION, RHD ............19-33
GEAR & LINK ROD - DESCRIPTION, LIFT . 8N-16
GEAR & LINK ROD - INSTALLATION, LIFT ............................... 8N-17
GEAR & LINK ROD - OPERATION, LIFT . . . 8N-16
GEAR & LINK ROD - REMOVAL, LIFT .....8N-16
GEAR - OPERATION .................... 19-26
GEAR - REMOVAL, LHD ...............19-26
GEAR - REMOVAL, RHD ...............19-29
GEAR SHIFT CABLE - INSTALLATION ....21-234
GEAR SHIFT CABLE - REMOVAL . . . 21-233,21-84
GEAR, SPECIAL TOOLS - POWER STEERING .......................... 19-34
GEARSHIFT CABLE ADJUSTMENT, ADJUSTMENTS ..................... 21-235
GEARTRAIN - DESCRIPTION, PLANETARY .................. 21-112,21-263
GEARTRAIN - OPERATION, PLANETARY . 21-112, 21-263
GENERAL - WARNINGS .............8W-01-7
GENERAL DIAGNOSIS - DIAGNOSIS AND TESTING, 4XTE TRANSAXLE .......21-149,21-5
GENERATOR - DESCRIPTION ...........8F-24
GENERATOR - OPERATION .............8F-24
GENERATOR DECOUPLER PULLEY - DESCRIPTION ....................... 8F-28
GENERATOR DECOUPLER PULLEY - DIAGNOSIS AND TESTING ..............8F-28
GENERATOR DECOUPLER PULLEY - INSTALLATION ....................... 8F-29
GENERATOR DECOUPLER PULLEY - OPERATION ......................... 8F-28
GENERATOR DECOUPLER PULLEY - REMOVAL .......................... 8F-29
GENERATOR, SPECIFICATIONS ..........8F-23
GLASS - DESCRIPTION, HEATED .........8G-1
GLASS - INSTALLATION, DOOR .........23-17
GLASS - INSTALLATION, LIFTGATE ......23-164
GLASS - INSTALLATION, SLIDING DOOR . 23-163
GLASS - OPERATION, HEATED ...........8G-2
GLASS - REMOVAL, DOOR .............23-16
GLASS - REMOVAL, LIFTGATE .........23-164
GLASS - REMOVAL, SLIDING DOOR .....23-163
GLASS INTEGRAL ANTENNA - EXPORT - DESCRIPTION, QUARTER ..............8A-13
GLASS INTEGRAL ANTENNA - EXPORT - OPERATION, QUARTER ................8A-13
GLASS INTEGRAL ANTENNA, EXPORT - QUARTER .......................... 8A-13
GLASS PANEL - INSTALLATION ........23-173
GLASS PANEL - REMOVAL ............23-173
GLASS PANEL ADJUSTMENT, ADJUSTMENTS - SUNROOF ...........23-173
GLASS RUN WEATHERSTRIP - INSTALLATION, FRONT DOOR ..........23-166
GLASS RUN WEATHERSTRIP - REMOVAL, FRONT DOOR .............23-166
GLASS-OUTSIDE REARVIEW MIRROR - INSTALLATION ....................... 23-61
GLASS-OUTSIDE REARVIEW MIRROR - REMOVAL .......................... 23-61
GLOVE BOX - INSTALLATION ...........23-66
GLOVE BOX - REMOVAL ...............23-66GLOVE BOX LAMP SWITCH -
INSTALLATION ....................... 8L-22
GLOVE BOX LAMP SWITCH - REMOVAL . . 8L-22
GLOVE BOX LATCH - INSTALLATION .....23-66
GLOVE BOX LATCH - REMOVAL .........23-66
GLOVE BOX LATCH STRIKER - INSTALLATION ....................... 23-66
GLOVE BOX LATCH STRIKER - REMOVAL . 23-66
GRID REPAIR PROCEDURE, STANDARD PROCEDURE ......................... 8G-5
GRILLE - DESCRIPTION ...............23-55
GRILLE - INSTALLATION ...............23-55
GRILLE - INSTALLATION, COWL .........23-50
GRILLE - REMOVAL ..................23-55
GRILLE - REMOVAL, COWL ............23-50
GROCERY BAG RETAINER - INSTALLATION, PLASTIC ..............23-149
GROCERY BAG RETAINER - REMOVAL, PLASTIC .......................... 23-149
GROMMET REPLACEMENT, STANDARD PROCEDURE - PUSH-PIN ..............8N-48
GROUND - OPERATION, PCM ...........8E-14
GROUND - STANDARD PROCEDURE, TESTING FOR A SHORT TO ..........8W-01-9
GROUND AND SPLICE INFORMATION - DESCRIPTION, CONNECTOR ..........8W-01-7
GROUND ON FUSES POWERING SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO.............................8W -01-10
GUIDE - INSTALLATION, UNDER SEAT STORAGE BIN ...................... 23-150
GUIDE - REMOVAL, UNDER SEAT STORAGE BIN ...................... 23-150
GUIDE PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - ASSEMBLY, CALIPER ....5-25
GUIDE PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - DISASSEMBLY,
CALIPER ............................ 5-24
GUIDE PINS (TRW BRAKES) - INSTALLATION, DISC BRAKE CALIPER .....5-32
GUIDE PINS (TRW BRAKES) - REMOVAL, DISC BRAKE CALIPER .................. 5-31
HALF SHAFT - DIAGNOSIS AND TESTING . . . 3-1
HALF SHAFT - FRONT - DESCRIPTION ......3-1
HALF SHAFT - FRONT - INSTALLATION .....3-4
HALF SHAFT - FRONT - REMOVAL .........3-2
HALF SHAFT - FRONT - SPECIFICATIONS ....3-6
HANDLE - INSTALLATION, ASSIST .......23-79
HANDLE - INSTALLATION, EXTERIOR ....23-22,
23-40
HANDLE - INSTALLATION, INSIDE LATCH . . 23-34
HANDLE - INSTALLATION, OUTSIDE ......23-36
HANDLE - INSTALLATION, RECLINER ....23-108
HANDLE - REMOVAL, ASSIST ...........23-79
HANDLE - REMOVAL, EXTERIOR . . . 23-21,23-40
HANDLE - REMOVAL, INSIDE LATCH .....23-34
HANDLE - REMOVAL, OUTSIDE .........23-35
HANDLE - REMOVAL, RECLINER .......23-108
HANDLE ACTUATOR - INSTALLATION, INSIDE ............................. 23-27
HANDLE ACTUATOR - REMOVAL, INSIDE . . 23-27
HANDLE CABLE - INSTALLATION, INSIDE . . 23-38
HANDLE CABLE - INSTALLATION, OUTSIDE ........................... 23-37
HANDLE CABLE - REMOVAL, INSIDE .....23-37
HANDLE CABLE - REMOVAL, OUTSIDE ....23-37
HANDLE SWITCH - DESCRIPTION, EXTERIOR .......................... 8N-10
HANDLE SWITCH - INSTALLATION, EXTERIOR .......................... 8N-10
HANDLE SWITCH - OPERATION, EXTERIOR .......................... 8N-10
HANDLE SWITCH - REMOVAL, EXTERIOR . 8N-10
HANDLING AIRBAGS - STANDARD PROCEDURE ......................... 8O-6
HANDLING TUBING AND FITTINGS, STANDARD PROCEDURE ...............24-69
HANDS FREE MODULE - INSTALLATION ....8T-3
HANDS FREE MODULE - REMOVAL .......8T-3
HARNESS - DESCRIPTION, WIRING ......8N-59
HARNESS - DIAGNOSIS AND TESTING, WIRING ..........................8W -01-7
HARNESS - INSTALLATION, WIRING .....8N-59
HARNESS - OPERATION, WIRING ........8N-59
HARNESS - REMOVAL, WIRING .........8N-59
HCU (HYDRAULIC CONTROL UNIT) - DESCRIPTION ....................... 5-100
RS INDEX15
Description Group-Page Description Group-Page Description Group-Page