2005 CHRYSLER CARAVAN turn signal

richer than optimum A/F mixture or vice versa. As
the PCM adjusts the air/fuel ratio, the sensor must
be able to rapidly detect the change. As the sensor
ages, it could take longer to detect the changes in the
oxygen content of the exhaust gas. The rate of
change that an oxygen sensor experiences is called
'Big Slope'. The PCM checks the oxygen sensor volt-
age in increments of a few milliseconds.
Reduced Output Voltage (Half Cycle)ÐThe
output voltage of the O2S ranges from 0 to 1 volt. A
good sensor can easily generate any output voltage in
this range as it is exposed to different concentrations
of oxygen. To detect a shift in the A/F mixture (lean
or rich), the output voltage has to change beyond a
threshold value. A malfunctioning sensor could have
difficulty changing beyond the threshold value. Many
times the condition is only temporey and the sensor
will recover. Under normal conditions the voltage sig-
nal surpasses the threshold, and a counter is incre-
mented by one. This is called the Half Cycle Counter.
Heater PerformanceÐThe heater is tested by a
separate monitor. Refer to the Oxygen Sensor Heater
Monitor.
OPERATIONÐAs the Oxygen Sensor signal
switches, the PCM monitors the half cycle and big
slope signals from the oxygen sensor. If during the
test neither counter reaches a predetermined value, a
malfunction is entered and a Freeze Frame is stored.
Only one counter reaching its predetermined value is
needed for the monitor to pass.
The Oxygen Sensor Signal Monitor is a two trip
monitor that is tested only once per trip. When the
Oxygen Sensor fails the test in two consecutive trips,
the MIL is illuminated and a DTC is set. The MIL is
extinguished when the Oxygen Sensor monitor
passes in three consecutive trips. The DTC is erased
from memory after 40 consecutive warm-up cycles
without test failure.
Enabling ConditionsÐThe following conditions
must typically be met for the PCM to run the oxygen
sensor monitor:
²Battery voltage
²Engine temperature
²Engine run time
²Engine run time at a predetermined speed
²Engine run time at a predetermined speed and
throttle opening
²Transmission in gear (automatic only)
²Fuel system in Closed Loop
²Long Term Adaptive (within parameters)
²Power Steering Switch in low PSI (no load)
²Engine at idle
²Fuel level above 15%
²Ambient air temperature
²Barometric pressure²Engine RPM within acceptable range of desired
idle
²Closed throttle speed
Pending ConditionsÐThe Task Manager typi-
cally does not run the Oxygen Sensor Signal Monitor
if overlapping monitors are running or the MIL is
illuminated for any of the following:
²Misfire Monitor
²Front Oxygen Sensor and Heater Monitor
²MAP Sensor
²Vehicle Speed Sensor
²Engine Coolant Temperature Sensor
²Throttle Position Sensor
²Engine Controller Self Test Faults
²Cam or Crank Sensor
²Injector and Coil
²Idle Air Control Motor
²EVAP Electrical
²EGR Solenoid Electrical
²Intake Air Temperature
²5 Volt Feed
ConflictÐThe Task Manager does not run the
Oxygen Sensor Monitor if any of the following condi-
tions are present:
²A/C ON (A/C clutch cycling temporarily sus-
pends monitor)
²Purge flow in progress
²Ethenal content learn is taking place and the
ethenal used once flag is set
SuspendÐThe Task Manager suspends maturing
a fault for the Oxygen Sensor Monitor if an of the fol-
lowing are present:
²Oxygen Sensor Heater Monitor, Priority 1
²Misfire Monitor, Priority 2
OXYGEN SENSOR HEATER MONITOR (NGC)
DESCRIPTIONÐIf the Oxygen sensor (O2S) DTC
as well as a O2S heater DTC is present, the O2S
Heater DTC MUST be repaired first. After the O2S
Heater is repaired, verify that the sensor circuit is
operating correctly.
The voltage reading taken from the O2S are very
temperature sensitive. The readings taken from the
O2S are not accurate below 300 degrees C. Heating
the O2S is done to allow the engine controller to shift
to closed loop control as soon as possible. The heating
element used to heat the O2S must be tested to
ensure that it is heating the sensor properly. Starting
with the introduction on the NGC module the strat-
egy for checking the heater circuit has changed. The
heater resistance is checked by the NGC almost
immediately after the engine is started. The same
O2S heater return pin used to read the heater resis-
tance is capable of detecting an open circuit, a
shorted high or shorted low condition.
RSEMISSIONS CONTROL25-3
EMISSIONS CONTROL (Continued)

OXYGEN SENSOR HEATER MONITOR (SBEC)
DESCRIPTIONÐIf there is an oxygen sensor
(O2S) DTC as well as a O2S heater DTC, the O2S
heater fault MUST be repaired first. After the O2S
fault is repaired, verify that the heater circuit is
operating correctly.
The voltage readings taken from the O2S are very
temperature sensitive. The readings are not accurate
below 300ÉC. Heating of the O2S is done to allow the
engine controller to shift to closed loop control as
soon as possible. The heating element used to heat
the O2S must be tested to ensure that it is heating
the sensor properly.
The heater element itself is not tested directly. The
sensor output is used to test the heater by isolating
the effect of the heater element on the O2S output
voltage from the other effects. The resistance is nor-
mally between 100 ohms and 4.5 megaohms. When
oxygen sensor temperature increases, the resistance
in the internal circuit decreases. The PCM sends a 5
volts biased signal through the oxygen sensors to
ground this monitoring circuit. As the temperature
increases, resistance decreases and the PCM detects
a lower voltage at the reference signal. Inversely, as
the temperature decreases, the resistance increases
and the PCM detects a higher voltage at the refer-
ence signal. The O2S circuit is monitored for a drop
in voltage.
OPERATIONÐThe Oxygen Sensor Heater Moni-
tor begins after the ignition has been turned OFF
and the O2 sensors have cooled. The PCM sends a 5
volt bias to the oxygen sensor every 1.6 seconds. The
PCM keeps it biased for 35 ms each time. As the sen-
sor cools down, the resistance increases and the PCM
reads the increase in voltage. Once voltage has
increased to a predetermined amount, higher than
when the test started, the oxygen sensor is cool
enough to test heater operation.
When the oxygen sensor is cool enough, the PCM
energizes the ASD relay. Voltage to the O2 sensor
begins to increase the temperature. As the sensor
temperature increases, the internal resistance
decreases. The PCM continues biasing the 5 volt sig-
nal to the sensor. Each time the signal is biased, the
PCM reads a voltage decrease. When the PCM
detects a voltage decrease of a predetermined value
for several biased pulses, the test passes.
The heater elements are tested each time the
engine is turned OFF if all the enabling conditions
are met. If the monitor fails, the PCM stores a
maturing fault and a Freeze Frame is entered. If two
consecutive tests fail, a DTC is stored. Because the
ignition is OFF, the MIL is illuminated at the begin-
ning of the next key cycle, after the 2nd failure.Enabling ConditionsÐThe following conditions
must be met for the PCM to run the oxygen sensor
heater test:
²Engine run time of at least 5.1 minutes
²Key OFF power down
²Battery voltage of at least 10 volts
²Sufficient Oxygen Sensor cool down
Pending ConditionsÐThere are not conditions or
situations that prompt conflict or suspension of test-
ing. The oxygen sensor heater test is not run pending
resolution of MIL illumination due to oxygen sensor
failure.
SuspendÐThere are no conditions which exist for
suspending the Heater Monitor.
CATALYST MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide.
Normal vehicle miles or engine misfire can cause a
catalyst to decay. A meltdown of the ceramic core can
cause a reduction of the exhaust passage. This can
increase vehicle emissions and deteriorate engine
performance, driveability and fuel economy.
The catalyst monitor uses dual oxygen sensors
(O2S's) to monitor the efficiency of the converter. The
dual O2S strategy is based on the fact that as a cat-
alyst deteriorates, its oxygen storage capacity and its
efficiency are both reduced. By monitoring the oxy-
gen storage capacity of a catalyst, its efficiency can
be indirectly calculated. The upstream O2S is used to
detect the amount of oxygen in the exhaust gas
before the gas enters the catalytic converter. The
PCM calculates the A/F mixture from the output of
the O2S. A low voltage indicates high oxygen content
(lean mixture). A high voltage indicates a low content
of oxygen (rich mixture).
When the upstream O2S detects a high oxygen
condition, there is an abundance of oxygen in the
exhaust gas. A functioning converter would store this
oxygen so it can use it for the oxidation of HC and
CO. As the converter absorbs the oxygen, there will
be a lack of oxygen downstream of the converter. The
output of the downstream O2S will indicate limited
activity in this condition.
As the converter loses the ability to store oxygen,
the condition can be detected from the behavior of
the downstream O2S. When the efficiency drops, no
chemical reaction takes place. This means the con-
centration of oxygen will be the same downstream as
upstream. The output voltage of the downstream
O2S copies the voltage of the upstream sensor. The
only difference is a time lag (seen by the PCM)
between the switching of the O2S's.
25 - 4 EMISSIONS CONTROLRS
EMISSIONS CONTROL (Continued)

INTERMEDIATE - INSTALLATION, CABLE- PARKING BRAKE ..................... 5-69
INTERMEDIATE - REMOVAL, CABLE - PARKING BRAKE ...................... 5-69
INTERNATIONAL SYMBOLS - DESCRIPTION .........................0-1
INTRODUCTION - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-3,9-78
IOD FUSE - DESCRIPTION ...........8W-97-3
IOD FUSE - OPERATION .............8W-97-3
JOINT - DESCRIPTION, LOWER BALL ......2-10
JOINT - DIAGNOSIS AND TESTING, LOWER BALL ........................ 2-10
JOINT - OPERATION, LOWER BALL .......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-60
JOINT MOLDING - REMOVAL, ROOF ......23-60
JOUNCE BUMPER - DESCRIPTION ........2-35
JOUNCE BUMPER - OPERATION ..........2-35
JUMP STARTING - STANDARD PROCEDURE ......................... 0-25
JUNCTION BLOCK - DESCRIPTION, NON-ABS ............................ 5-33
JUNCTION BLOCK - INSTALLATION, NON-ABS ............................ 5-34
JUNCTION BLOCK - OPERATION, NON-ABS ............................ 5-33
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-34
KEY - DESCRIPTION, TRANSPONDER .....8Q-6
KEY - OPERATION, TRANSPONDER .......8Q-6
KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........23-90
KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ...........23-90
KEY REMOTE ENTRY MODULE - DESCRIPTION, SENTRY ................8Q-3
KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY .......8Q-5
KEY REMOTE ENTRY MODULE - INSTALLATION, SENTRY ................8Q-6
KEY REMOTE ENTRY MODULE - OPERATION, SENTRY .................. 8Q-4
KEY REMOTE ENTRY MODULE - REMOVAL, SENTRY ................... 8Q-6
KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY .......8Q-3
KEYLESS ENTRY TRANSMITTER, DIAGNOSIS AND TESTING .............8N-24
KEYLESS ENTRY TRANSMITTER PROGRAMMING - STANDARD
PROCEDURE, REMOTE ................8N-24
KEY/LOCK CYLINDER - DESCRIPTION ....19-20
KEY/LOCK CYLINDER - INSTALLATION ....19-20
KEY/LOCK CYLINDER - OPERATION ......19-20
KEY/LOCK CYLINDER - REMOVAL .......19-20
KNEE - INSTALLATION, BLOCKER- INFLATABLE ......................... 23-75
KNEE - REMOVAL, BLOCKER- INFLATABLE ......................... 23-75
KNEE BLOCKER AIRBAG - DESCRIPTION . . 8O-22
KNEE BLOCKER AIRBAG - INSTALLATION . 8O-23
KNEE BLOCKER AIRBAG - OPERATION . . . 8O-22
KNEE BLOCKER AIRBAG - REMOVAL .....8O-23
KNOB - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
KNOB - REMOVAL, SEAT BELT HEIGHT ADJUSTER ......................... 8O-38
KNOCK SENSOR - DESCRIPTION ..........8I-8
KNOCK SENSOR - OPERATION ...........8I-8
KNUCKLE - DESCRIPTION ................2-6
KNUCKLE - INSPECTION, STEERING ........2-9
KNUCKLE - INSTALLATION, STEERING ......2-9
KNUCKLE - OPERATION .................2-7
KNUCKLE - REMOVAL, STEERING .........2-7
LABEL, DESCRIPTION - VEHICLE EMISSION CONTROL INFORMATION .......25-1
LAMP - DESCRIPTION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - DIAGNOSIS AND TESTING, FRONT FOG .......................... 8L-7
LAMP - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP - INSTALLATION, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - INSTALLATION, COURTESY ......8L-21
LAMP - INSTALLATION, DOME/CARGO ....8L-22
LAMP - INSTALLATION, FRONT FOG .......8L-8
LAMP - INSTALLATION, LICENSE ........8L-17
LAMP - INSTALLATION, LIFTGATE .......8L-22 LAMP - INSTALLATION, PARK/TURN
SIGNAL ............................ 8L-18
LAMP - INSTALLATION, READING ........8L-23
LAMP - INSTALLATION, TAIL ...........8L-19
LAMP - INSTALLATION, VANITY .........8L-24
LAMP - OPERATION, VTSS/SKIS INDICATOR .......................... 8Q-8
LAMP - REMOVAL, CENTER CONSOLE ....8L-21
LAMP - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP - REMOVAL, COURTESY ..........8L-21
LAMP - REMOVAL, DOME/CARGO .......8L-22
LAMP - REMOVAL, FRONT FOG ..........8L-8
LAMP - REMOVAL, LICENSE ............8L-17
LAMP - REMOVAL, LIFTGATE ...........8L-22
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-18
LAMP - REMOVAL, READING ...........8L-22
LAMP - REMOVAL, TAIL ...............8L-18
LAMP - REMOVAL, VANITY .............8L-24
LAMP SWITCH - DESCRIPTION, BRAKE ....8L-4
LAMP SWITCH - DIAGNOSIS AND TESTING, BRAKE ...................... 8L-4
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-5
LAMP SWITCH - INSTALLATION, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - INSTALLATION, GLOVE BOX ............................... 8L-22
LAMP SWITCH - OPERATION, BRAKE ......8L-4
LAMP SWITCH - REMOVAL, BRAKE .......8L-5
LAMP SWITCH - REMOVAL, CENTER CONSOLE ........................... 8L-21
LAMP SWITCH - REMOVAL, GLOVE BOX . . 8L-22
LAMP UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP .................8L-6
LAMP UNIT - INSTALLATION, TAIL .......8L-19
LAMP UNIT - REMOVAL, CENTER HIGH MOUNTED STOP ...................... 8L-6
LAMP UNIT - REMOVAL, TAIL ...........8L-19
LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG .....8L-9
LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG ...............8L-9
LAMPS - INSTALLATION, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS - REMOVAL, CLUSTER ILLUMINATION ...................... 8L-21
LAMPS, SPECIFICATIONS - EXTERIOR .....8L-3
LAMPS, SPECIFICATIONS - INTERIOR ....8L-20
LAMPS/LIGHTING - EXTERIOR - DESCRIPTION ........................ 8L-2
LAMPS/LIGHTING - EXTERIOR - OPERATION .......................... 8L-2
LAMPS/LIGHTING - EXTERIOR - WARNING ........................... 8L-3
LAP BELT - FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER .....23-157
LAP BELT - FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER .................. 23-157
LASH ADJUSTER NOISE DIAGNOSIS - DIAGNOSIS AND TESTING, HYDRAULIC ....9-34
LASH ADJUSTERS - INSTALLATION, HYDRAULIC .......................... 9-35
LASH ADJUSTERS - REMOVAL, HYDRAULIC .......................... 9-35
LATCH - DESCRIPTION ...........8N-12,8N-49
LATCH - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID ....23-90
LATCH - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID .................23-90
LATCH - INSTALLATION .....23-18,23-41,23-63
LATCH - INSTALLATION ..........8N-13,8N-50
LATCH - INSTALLATION, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH - INSTALLATION, GLOVE BOX .....23-66
LATCH - INSTALLATION, HOLD OPEN .....23-25
LATCH / LOCK ASSEMBLY - INSTALLATION ....................... 23-27
LATCH / LOCK ASSEMBLY - REMOVAL ....23-26
LATCH - OPERATION ............8N-12,8N-49
LATCH - REMOVAL .........23-18,23-41,23-63
LATCH - REMOVAL ..............8N-12,8N-49
LATCH - REMOVAL, FUEL FILL DOOR BLOCKER ........................... 23-53
LATCH - REMOVAL, GLOVE BOX .........23-66
LATCH - REMOVAL, HOLD OPEN ........23-25
LATCH ACTUATOR - DESCRIPTION ......8N-13
LATCH ACTUATOR - INSTALLATION ......8N-14
LATCH ACTUATOR - OPERATION ........8N-13 LATCH ACTUATOR - REMOVAL
..........8N-13
LATCH CABLE - INSTALLATION, HOLD OPEN .............................. 23-38
LATCH CABLE - REMOVAL, HOLD OPEN . . . 23-38
LATCH HANDLE - INSTALLATION, INSIDE . . 23-34
LATCH HANDLE - REMOVAL, INSIDE .....23-34
LATCH LOCKING LINK - INSTALLATION, SEAT RISER ........................ 23-151
LATCH LOCKING LINK - REMOVAL, SEAT RISER ............................ 23-151
LATCH RELEASE CABLE - INSTALLATION . . 23-64
LATCH RELEASE CABLE - REMOVAL .....23-63
LATCH STRIKER - INSTALLATION . . 23-19,23-42, 23-64
LATCH STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER .................23-53
LATCH STRIKER - INSTALLATION, GLOVE BOX ............................... 23-66
LATCH STRIKER - INSTALLATION, HOLD OPEN .............................. 23-26
LATCH STRIKER - INSTALLATION, REAR . . 23-29
LATCH STRIKER - REMOVAL . 23-19,23-41,23-64
LATCH STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER ..................... 23-53
LATCH STRIKER - REMOVAL, GLOVE BOX ............................... 23-66
LATCH STRIKER - REMOVAL, HOLD OPEN .............................. 23-26
LATCH STRIKER - REMOVAL, REAR ......23-29
LEAD - DIAGNOSIS AND TESTING, TIRE/VEHICLE ......................... 22-14
LEAF SPRING FRONT - INSTALLATION, BUSHING ............................ 2-30
LEAF SPRING FRONT - REMOVAL, BUSHING ............................ 2-29
LEAK DETECTION ASSY - INSTALLATION, NATURAL VAC ....................... 25-14
LEAK DETECTION ASSY - REMOVAL, NATURAL VAC ....................... 25-14
LEAK DETECTION PUMP - INSTALLATION . 25-15
LEAK DETECTION PUMP - REMOVAL .....25-15
LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE OIL ...............9-8,9-84
LEAK REPAIRING - STANDARD PROCEDURE, TIRE ................... 22-17
LEAK TEST - DIAGNOSIS AND TESTING, COOLING SYSTEM .....................7-2
LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER HOUSING FLUID . . 21-154, 21-9
LEAKAGE TEST - DIAGNOSIS AND TESTING, CYLINDER COMBUSTION
PRESSURE ....................... 9-85,9-9
LEAKS - DIAGNOSIS AND TESTING, INTAKE MANIFOLD ...............9-147,9-60
LEAKS, DIAGNOSIS AND TESTING - REFRIGERANT SYSTEM ...............24-67
LEAKS, DIAGNOSIS AND TESTING - WATER ............................. 23-1
LEARN CYCLE, STANDARD PROCEDURE - POWER LIFTGATE ................... 8N-8
LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING DOOR ..............8N-48
LEARN PROCEDURE - STANDARD PROCEDURE, QUICK .................. 8E-15
LENS - INSTALLATION, CLUSTER ........8J-11
LENS - REMOVAL, CLUSTER ............8J-11
LEVEL AND CONDITION CHECK, STANDARD PROCEDURE - FLUID . . 21-230,21-82
LEVEL CHECK - STANDARD PROCEDURE, COOLANT .................7-4
LEVEL CHECK - STANDARD PROCEDURE, ENGINE OIL ..............9-140
LEVEL CHECK, STANDARD PROCEDURE - ENGINE OIL ........................ 9-54
LEVEL CHECKING - STANDARD PROCEDURE, BRAKE FLUID .............5-33
LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING FLUID . . . 19-44
LEVEL SENDING UNIT / SENSOR - DESCRIPTION, FUEL ................... 14-5
LEVEL SENDING UNIT / SENSOR - INSTALLATION, FUEL .................. 14-6
LEVEL SENDING UNIT / SENSOR - OPERATION, FUEL ..................... 14-5
LEVEL SENDING UNIT / SENSOR - REMOVAL, FUEL ...................... 14-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

PANEL TOP COVER - REMOVAL,INSTRUMENT ....................... 23-72
PANEL TOP PAD ASSEMBLY - INSTALLATION, INSTRUMENT ...........23-77
PANEL TOP PAD ASSEMBLY - REMOVAL, INSTRUMENT ....................... 23-77
PANEL/FENDER AIR EXHAUSTER - DESCRIPTION, REAR QUARTER .........23-59
PANEL/FENDER AIR EXHAUSTER - INSTALLATION, REAR QUARTER .........23-60
PANEL/FENDER AIR EXHAUSTER - REMOVAL, REAR QUARTER ............23-59
PANEL-THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, BOTTOM OF SEAT
CUSHION PAN ...................... 23-152
PANEL-THIRD ROW - FOLD-IN-FLOOR - REMOVAL, BOTTOM OF SEAT
CUSHION PAN ...................... 23-152
PARK ASSIST DISPLAY - DESCRIPTION ....8B-3
PARK ASSIST DISPLAY - INSTALLATION . . . 8B-4
PARK ASSIST DISPLAY - OPERATION .....8B-3
PARK ASSIST DISPLAY - REMOVAL .......8B-4
PARK ASSIST MODULE - DESCRIPTION ....8B-4
PARK ASSIST MODULE - INSTALLATION . . . 8B-6
PARK ASSIST MODULE - OPERATION .....8B-5
PARK ASSIST MODULE - REMOVAL .......8B-5
PARK ASSIST SENSOR - DESCRIPTION ....8B-6
PARK ASSIST SENSOR - INSTALLATION . . . 8B-6
PARK ASSIST SENSOR - OPERATION ......8B-6
PARK ASSIST SENSOR - REMOVAL .......8B-6
PARK SWITCH - DIAGNOSIS AND TESTING, FAILED ..................... 8R-2
PARKING BRAKE - INSTALLATION, LEVER .............................. 5-76
PARKING BRAKE - INSTALLATION, SHOES .............................. 5-84
PARKING BRAKE - REMOVAL, LEVER ......5-75
PARKING BRAKE - REMOVAL, SHOES .....5-78
PARKING BRAKE AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD
PROCEDURE ......................... 5-63
PARKING BRAKE AUTOMATIC ADJUSTER TENSION RESET - STANDARD
PROCEDURE ......................... 5-64
PARKING BRAKE CABLES - ADJUSTMENT ........................ 5-65
PARKING BRAKE INTERMEDIATE - INSTALLATION, CABLE .................5-69
PARKING BRAKE INTERMEDIATE - REMOVAL, CABLE ..................... 5-69
PARKING BRAKE LEVER AND FRONT CABLE - INSTALLATION ................5-77
PARKING BRAKE LEVER AND FRONT CABLE - REMOVAL .................... 5-77
PARKING BRAKE SHOES - ADJUSTMENT . . . 5-85
PARK/TURN SIGNAL LAMP - INSTALLATION ....................... 8L-18
PARK/TURN SIGNAL LAMP - REMOVAL . . . 8L-18
PARTS - DESCRIPTION, FFV REPLACEMENT ....................... 14-2
PASSENGER AIRBAG - DESCRIPTION ....8O-30
PASSENGER AIRBAG - INSTALLATION ....8O-32
PASSENGER AIRBAG - OPERATION ......8O-30
PASSENGER AIRBAG - REMOVAL ........8O-30
PASSENGER AIRBAG DISABLED INDICATOR - DESCRIPTION ............8O-33
PASSENGER AIRBAG DISABLED INDICATOR - INSTALLATION ............8O-34
PASSENGER AIRBAG DISABLED INDICATOR - OPERATION ..............8O-33
PASSENGER AIRBAG DISABLED INDICATOR - REMOVAL ...............8O-34
PASSENGER BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW -
THREE ............................. 8O-40
PASSENGER BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW - THREE . . . 8O-40
PATTERNS - DIAGNOSIS AND TESTING, TIRE WEAR ......................... 22-16
PCM GROUND - OPERATION ...........8E-14
PCM INPUT - OPERATION, DATA BUS COMMUNICATION RECEIVE .............8E-14
PCM INPUT - OPERATION, IGNITION SENSE ............................. 8E-14
PCM INPUT - OPERATION, SENSOR RETURN ............................ 8E-14
PCM OUTPUT - OPERATION, 5 VOLT SUPPLY ............................ 8E-15PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE ......................... 8E-1
PCV SYSTEM - DIAGNOSIS AND TESTING ........................... 25-18
PCV VALVE - DESCRIPTION ............25-18
PCV VALVE - OPERATION ..............25-18
PEDAL - INSTALLATION, ACCELERATOR . . . 14-28
PEDAL - REMOVAL, ACCELERATOR ......14-28
PEDAL TORQUE SHAFT - RHD - INSTALLATION ........................ 5-44
PEDAL TORQUE SHAFT - RHD - REMOVAL ........................... 5-44
PEDALS - ADJUSTABLE - INSTALLATION . . . 5-43
PEDALS - ADJUSTABLE - REMOVAL .......5-40
PEDALS SWITCH - INSTALLATION, ADJUSTABLE ......................... 5-11
PEDALS SWITCH - REMOVAL, ADJUSTABLE ......................... 5-11
PERFORMANCE - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-4,9-80
PERFORMANCE TEST, DIAGNOSIS AND TESTING - A/C ........................ 24-7
PERFORMANCE TEST, DIAGNOSIS AND TESTING - HEATER ................... 24-10
PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - ASSEMBLY, CALIPER GUIDE ....5-25
PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - DISASSEMBLY, CALIPER
GUIDE .............................. 5-24
PINCH SENSOR - DESCRIPTION .........8N-17
PINCH SENSOR - INSTALLATION ........8N-18
PINCH SENSOR - OPERATION ..........8N-17
PINCH SENSOR - REMOVAL ............8N-18
PINION FACTOR SETTING - STANDARD PROCEDURE ........................ 8E-15
PINS (TRW BRAKES) - INSTALLATION, DISC BRAKE CALIPER GUIDE ............5-32
PINS (TRW BRAKES) - REMOVAL, DISC BRAKE CALIPER GUIDE ................5-31
PIPE - 3.3/3.8L - INSTALLATION, CROSS-OVER ........................ 11-6
PIPE - 3.3/3.8L - REMOVAL, CROSS- OVER ............................... 11-6
PIPE - INSTALLATION, AIR INTAKE ......24-115
PIPE - REMOVAL, AIR INTAKE .........24-115
PIPES - INSTALLATION, HEATER ........24-120
PIPES - REMOVAL, HEATER ...........24-119
PISTON & CONNECTING ROD - DESCRIPTION ................... 9-119,9-44
PISTON & CONNECTING ROD - INSTALLATION ........................ 9-45
PISTON & CONNECTING ROD - REMOVAL ........................... 9-44
PISTON AND SEAL - ASSEMBLY, CALIPER ........................ 5-26,5-30
PISTON AND SEAL - DISASSEMBLY, CALIPER ........................ 5-24,5-28
PISTON RING, FITTING .................9-47
PISTON RING FITTING - STANDARD PROCEDURE ........................ 9-124
PISTON RINGS - INSTALLATION .........9-124
PISTON RINGS - REMOVAL ............9-124
PISTON TO CYLINDER BORE FITTING - STANDARD PROCEDURE ................9-44
PISTONS - STANDARD PROCEDURE, FITTING ............................ 9-120
PLANETARY GEARTRAIN - DESCRIPTION ................ 21-112,21-263
PLANETARY GEARTRAIN - OPERATION . . 21-112, 21-263
PLASTIC BODY PANEL REPAIR - STANDARD PROCEDURE ................23-3
PLASTIC GROCERY BAG RETAINER - INSTALLATION ...................... 23-149
PLASTIC GROCERY BAG RETAINER - REMOVAL ......................... 23-149
PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING CLEARANCE
USING .......................... 9-12,9-86
PLATINUM PLUGS - DESCRIPTION ........8I-9
PLAYER - DESCRIPTION, DVD ..........8A-12
PLAYER - INSTALLATION, DVD ..........8A-12
PLAYER - REMOVAL, DVD .............8A-12
PLUG CABLE - DESCRIPTION, SPARK .....8I-10
PLUG CABLE RESISTANCE, SPECIFICATIONS - SPARK ...............8I-2
PLUG, SPECIFICATIONS - SPARK .........8I-2
PLUGS - DESCRIPTION, PLATINUM ........8I-9PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY ....9-10,9-88
PLUMBING - FRONT - DESCRIPTION .....24-65
PLUMBING - FRONT - OPERATION .......24-65
POINTS - DESCRIPTION, LUBRICATION .....0-7
POLISHING - DESCRIPTION, FINESSE SANDING/BUFFING .................. 23-101
PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD
VACUUM ........................... 9-148
PORT VALVE CORE - DESCRIPTION, SERVICE ........................... 24-95
PORT VALVE CORE - INSTALLATION, SERVICE ........................... 24-95
PORT VALVE CORE - REMOVAL, SERVICE ........................... 24-95
POSITION SENSOR - DESCRIPTION, CAMSHAFT ........................... 8I-4
POSITION SENSOR - DESCRIPTION, CRANKSHAFT ....................... 14-29
POSITION SENSOR - DESCRIPTION, THROTTLE .......................... 14-40
POSITION SENSOR - OPERATION, CAMSHAFT ........................... 8I-4
POSITION SENSOR - OPERATION, CRANKSHAFT ....................... 14-29
POSITION SENSOR - OPERATION, THROTTLE .......................... 14-41
POSITION SENSOR - REMOVAL, CRANKSHAFT ....................... 14-30
POTENTIAL - STANDARD PROCEDURE, TESTING OF VOLTAGE ..............8W-01-9
POWER - INSTALLATION, WINDOW REGULATOR ........................ 23-22
POWER - REMOVAL, WINDOW REGULATOR ........................ 23-22
POWER ADJUSTER - INSTALLATION, FRONT SEAT TRACK .................23-124
POWER ADJUSTER - REMOVAL, FRONT SEAT TRACK ....................... 23-124
POWER BRAKE BOOSTER - DESCRIPTION ........................ 5-45
POWER BRAKE BOOSTER - DIAGNOSIS AND TESTING ........................ 5-46
POWER BRAKE BOOSTER - OPERATION . . . 5-46
POWER DISTRIBUTION SYSTEM - DESCRIPTION .....................8W -97-1
POWER DISTRIBUTION SYSTEM - OPERATION .......................8W -97-1
POWER DISTRIBUTION SYSTEMS, SPECIAL TOOLS ...................8W -97-1
POWER FOLDAWAY MIRROR SWITCH - EXPORT - DESCRIPTION ...............8N-29
POWER FOLDAWAY MIRROR SWITCH - EXPORT - INSTALLATION ..............8N-30
POWER FOLDAWAY MIRROR SWITCH - EXPORT - OPERATION ................8N-29
POWER FOLDAWAY MIRROR SWITCH - EXPORT - REMOVAL .................. 8N-29
POWER LIFTGATE CONTROL MODULE - DESCRIPTION ....................... 8E-10
POWER LIFTGATE CONTROL MODULE - OPERATION ......................... 8E-10
POWER LIFTGATE CONTROL MODULE, DIAGNOSIS AND TESTING .............8E-10
POWER LIFTGATE LEARN CYCLE, STANDARD PROCEDURE ...............8N-8
POWER LIFTGATE SYSTEM - DESCRIPTION ........................ 8N-2
POWER LIFTGATE SYSTEM - OPERATION . . 8N-2
POWER LIFTGATE SYSTEM, DIAGNOSIS AND TESTING ........................ 8N-3
POWER LOCKS - DESCRIPTION .........8N-20
POWER LOCKS - OPERATION ...........8N-21
POWER MIRRORS - DESCRIPTION ......8N-26
POWER MIRRORS - OPERATION ........8N-26
POWER MIRRORS, DIAGNOSIS AND TESTING ........................... 8N-27
POWER MODULE - BLOWER MOTOR - DESCRIPTION ....................... 24-30
POWER MODULE - BLOWER MOTOR - INSTALLATION ....................... 24-31
POWER MODULE - BLOWER MOTOR - OPERATION ......................... 24-30
POWER MODULE - BLOWER MOTOR - REMOVAL .......................... 24-30
POWER MODULE - DESCRIPTION, INTEGRATED ......................8W -97-1
RS INDEX23
Description Group-Page Description Group-Page Description Group-Page

SENSOR - OPERATION, BATTERYTEMPERATURE ...................... 8F-24
SENSOR - OPERATION, BELT TENSION ....8O-9
SENSOR - OPERATION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - OPERATION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - OPERATION, ENGINE SPEED . . . 14-30
SENSOR - OPERATION, EVAPORATOR TEMPERATURE ...................... 24-27
SENSOR - OPERATION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - OPERATION, HEATED SEAT ....8G-13
SENSOR - OPERATION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - OPERATION, KNOCK ...........8I-8
SENSOR - OPERATION, MAP ...........14-34
SENSOR - OPERATION, O2 .............14-36
SENSOR - OPERATION, PARK ASSIST .....8B-6
SENSOR - OPERATION, PINCH ..........8N-17
SENSOR - OPERATION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-44
SENSOR - OPERATION, THROTTLE POSITION .......................... 14-41
SENSOR - OPERATION, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - OUTPUT - DESCRIPTION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - INSTALLATION, SPEED ...................... 21-123,21-274
SENSOR - OUTPUT - OPERATION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - REMOVAL, SPEED . 21-123, 21-274
SENSOR - REMOVAL, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - REMOVAL, CRANKSHAFT POSITION .......................... 14-30
SENSOR - REMOVAL, FRONT WHEEL SPEED .............................. 5-91
SENSOR - REMOVAL, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - REMOVAL, IMPACT ..........8O-19
SENSOR - REMOVAL, PARK ASSIST ......8B-6
SENSOR - REMOVAL, PINCH ...........8N-18
SENSOR - REMOVAL, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - SPECIFICATIONS, BATTERY TEMPERATURE ...................... 8F-23
SENSOR - TPM - CAUTION .............22-11
SENSOR - TPM - DESCRIPTION .........22-10
SENSOR - TPM - INSTALLATION ........22-11
SENSOR - TPM - OPERATION ...........22-10
SENSOR - TPM - REMOVAL ............22-11
SENSOR AIR GAP, SPECIFICATIONS - WHEEL SPEED ........................ 5-91
SENSOR CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE .....8M-12
SENSOR, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE ..............8M-12
SENSOR, DIAGNOSIS AND TESTING - HEATED SEAT ....................... 8G-13
SENSOR RETURN - PCM INPUT - OPERATION ......................... 8E-14
SENTRY KEY REMOTE ENTRY MODULE - DESCRIPTION ........................ 8Q-3
SENTRY KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING ..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE - INSTALLATION ....................... 8Q-6
SENTRY KEY REMOTE ENTRY MODULE - OPERATION .......................... 8Q-4
SENTRY KEY REMOTE ENTRY MODULE - REMOVAL ........................... 8Q-6
SENTRY KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
SERVO - DESCRIPTION .................8P-4
SERVO - INSTALLATION ................8P-4
SERVO - OPERATION ..................8P-4
SERVO - REMOVAL .................... 8P-4
SETTING - STANDARD PROCEDURE, PINION FACTOR ...................... 8E-15
SETTING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
SEVERAL LOADS - STANDARD PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHACKLE - INSTALLATION, SPRING .......2-44 SHACKLE - REMOVAL, SPRING
..........2-44
SHAFT - ASSEMBLY, ROCKER ARMS .....9-113
SHAFT - DIAGNOSIS AND TESTING, HALF ................................3-1
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-113
SHAFT - FRONT - DESCRIPTION, HALF .....3-1
SHAFT - FRONT - INSTALLATION, HALF .....3-4
SHAFT - FRONT - REMOVAL, HALF ........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . . 3-6
SHAFT - INSTALLATION, ROCKER ARMS . . 9-113
SHAFT - REMOVAL, ROCKER ARMS ......9-112
SHAFT - RHD - INSTALLATION, PEDAL TORQUE ............................ 5-44
SHAFT - RHD - REMOVAL, PEDAL TORQUE ............................ 5-44
SHAFTS AND CARRIER ASSEMBLY - DESCRIPTION, BALANCE ................9-71
SHAFTS AND CARRIER ASSEMBLY - INSTALLATION, BALANCE ...............9-73
SHAFTS AND CARRIER ASSEMBLY - OPERATION, BALANCE .................9-71
SHAFTS AND CARRIER ASSEMBLY - REMOVAL, BALANCE ................... 9-71
SHIELD - INSTALLATION, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT
SIDE ............................. 23-143
SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE ............23-143
SHIELD - REMOVAL, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT
CUSHION SIDE ..................... 23-138
SHIELD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT CUSHION
SIDE ............................. 23-138
SHIELD CUP HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE ...............23-160
SHIELD CUP HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE ................... 23-160
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE ............23-151
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE .................. 23-151
SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE ............23-142
SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE .................. 23-141
SHIELDS - DESCRIPTION, HEAT ..........11-7
SHIELDS - INSTALLATION, HEAT .........11-7
SHIELDS - OPERATION, HEAT ............11-7
SHIELDS - REMOVAL, HEAT .............11-7
SHIFT CABLE - INSTALLATION, GEAR ....21-234
SHIFT CABLE - REMOVAL, GEAR . . 21-233,21-84
SHIFT INTERLOCK SOLENOID - DESCRIPTION ................ 21-113,21-264
SHIFT INTERLOCK SOLENOID - DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION ............... 21-115,21-266
SHIFT INTERLOCK SOLENOID - INSTALLATION ................ 21-116,21-267
SHIFT INTERLOCK SOLENOID - OPERATION .................. 21-114,21-265
SHIFT INTERLOCK SOLENOID - REMOVAL ................... 21-115,21-266
SHOCK ABSORBER - DESCRIPTION .......2-36
SHOCK ABSORBER - INSTALLATION ......2-38
SHOCK ABSORBER - OPERATION .........2-36
SHOCK ABSORBER - REMOVAL ..........2-36
SHOCK ABSORBER (UPPER BUSHING) - ASSEMBLY .......................... 2-37
SHOCK ABSORBER (UPPER BUSHING) - DISASSEMBLY ........................ 2-37
SHOE LINING - INSPECTION, REAR DRUM BRAKE ........................ 5-22
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-85
SHOES - ADJUSTMENT, REAR DRUM BRAKE .............................. 5-23
SHOES - CLEANING, DISC BRAKE ....5-16,5-18
SHOES - INSPECTION, DISC BRAKE . . . 5-16,5-18
SHOES - INSTALLATION, REAR DISC BRAKE .............................. 5-19
SHOES - INSTALLATION, REAR DRUM BRAKE .............................. 5-22SHOES - PARKING BRAKE -
INSTALLATION ........................ 5-84
SHOES - PARKING BRAKE - REMOVAL ....5-78
SHOES - REMOVAL, REAR DISC BRAKE ....5-17
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19
SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT DISC BRAKE ......5-16
SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC BRAKE ..........5-15
SHOES (TRW BRAKES) - INSTALLATION, FRONT DISC BRAKE ................... 5-17
SHOES (TRW BRAKES) - REMOVAL, FRONT DISC BRAKE ................... 5-15
SHORT TO GROUND - STANDARD PROCEDURE, TESTING FOR A ........8W-01-9
SHORT TO GROUND ON FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ..........................8W -01-10
SHROUD - LOWER - INSTALLATION ......19-21
SHROUD - LOWER - REMOVAL .........19-21
SHROUD - UPPER - INSTALLATION ......19-22
SHROUD - UPPER - REMOVAL ..........19-22
SHUT DOWN RELAY - DESCRIPTION, AUTO ............................... 8I-3
SHUT DOWN RELAY - OPERATION, AUTO . . . 8I-3
SIDE - INSTALLATION, BODY ...........23-44
SIDE - INSTALLATION, LIFTGATE ........23-44
SIDE - REMOVAL, BODY ...............23-44
SIDE - REMOVAL, LIFTGATE ............23-44
SIDE COVER - INSTALLATION, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - OCS - INSTALLATION, FRONT SEAT CUSHION ...............23-122
SIDE COVER - OCS - REMOVAL, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - REMOVAL, FRONT SEAT CUSHION .......................... 23-120
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY .....23-45
SIDE SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-143
SIDE SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT ........23-143
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT
CUSHION .......................... 23-138
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT
CUSHION .......................... 23-138
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - INSTALLATION ..............23-160
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - REMOVAL .................. 23-160
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT .................23-151
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT ...................... 23-151
SIDE SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-142
SIDE SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT .................23-141
SIDE VIEW MIRROR - INSTALLATION .....23-60
SIDE VIEW MIRROR - REMOVAL ........23-60
SIDEVIEW MIRROR - REMOVAL .........8N-30
SIGNAL LAMP - INSTALLATION, PARK/TURN ......................... 8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN ....8L-17
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-95
SILL PLATE - INSTALLATION, SLIDING DOOR ............................. 23-99
SILL PLATE - REMOVAL, LIFTGATE .......23-94
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-98
SILL TRIM PLATE - INSTALLATION, DOOR ............................. 23-89
SILL TRIM PLATE - REMOVAL, DOOR ....23-89
SINGLE ZONE, DESCRIPTION - MANUAL . . . 24-2
SINGLE ZONE, OPERATION - MANUAL .....24-4
SLEEVE - INSTALLATION, HEADREST ....23-107
SLEEVE - REMOVAL, HEADREST .......23-107
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, HEADREST ....23-131
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, HEADREST ........23-131
RS INDEX29
Description Group-Page Description Group-Page Description Group-Page

TUBE - REMOVAL, DRAIN.............23-172
TUBE - REMOVAL, EXHAUST ..........24-116
TUBE - REMOVAL, FUEL TANK FILLER ....14-16
TUBES AND HOSES - DESCRIPTION, BRAKE .............................. 5-14
TUBES AND HOSES - INSPECTION, BRAKE .............................. 5-14
TUBES AND HOSES - OPERATION, BRAKE .............................. 5-14
TUBES, INSTALLATION - FRONT HEATER CORE .............................. 24-85
TUBES, INSTALLATION - UNDERBODY HEATER ........................... 24-112
TUBES, REMOVAL - FRONT HEATER CORE .............................. 24-84
TUBES, REMOVAL - UNDERBODY HEATER ........................... 24-109
TUBING AND FITTINGS, STANDARD PROCEDURE - HANDLING ..............24-69
TUMBLER - FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE KEY
LOCK .............................. 23-90
TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK ............23-90
TURN SIGNAL SYSTEM - DESCRIPTION . . . 8L-17
TURN SIGNAL SYSTEM - OPERATION ....8L-17
UNDER SEAT STORAGE BIN - INSTALLATION ...................... 23-149
UNDER SEAT STORAGE BIN - REMOVAL . 23-149
UNDER SEAT STORAGE BIN GUIDE - INSTALLATION ...................... 23-150
UNDER SEAT STORAGE BIN GUIDE - REMOVAL ......................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - INSTALLATION .................... 23-150
UNDER SEAT STORAGE BIN LOCK/LATCH - REMOVAL ........................ 23-150
UNDERBODY HEATER TUBES, INSTALLATION ...................... 24-112
UNDERBODY HEATER TUBES, REMOVAL . 24-109
UNDERBODY LINES - DESCRIPTION .....24-108
UNDERBODY LINES - OPERATION ......24-108
UNDERBODY REFRIGERANT LINES, INSTALLATION ...................... 24-112
UNDERBODY REFRIGERANT LINES, REMOVAL ......................... 24-110
UNIT - DESCRIPTION, LOWER DRIVE ....8N-53
UNIT - EXPORT - INSTALLATION, HEADLAMP ......................... 8L-17
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-17
UNIT - INSTALLATION, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - INSTALLATION, HEADLAMP .......8L-15
UNIT - INSTALLATION, HEATER ........24-122
UNIT - INSTALLATION, LOWER DRIVE ....8N-54
UNIT - INSTALLATION, TAIL LAMP .......8L-19
UNIT - OPERATION, LOWER DRIVE ......8N-53
UNIT - REMOVAL, CENTER HIGH MOUNTED STOP LAMP .................8L-6
UNIT - REMOVAL, HEADLAMP ..........8L-15
UNIT - REMOVAL, HEATER ............24-121
UNIT - REMOVAL, LOWER DRIVE .......8N-53
UNIT - REMOVAL, TAIL LAMP ...........8L-19
UNIT / SENSOR - DESCRIPTION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - INSTALLATION, FUEL LEVEL SENDING ...................... 14-6
UNIT / SENSOR - OPERATION, FUEL LEVEL SENDING ...................... 14-5
UNIT / SENSOR - REMOVAL, FUEL LEVEL SENDING ...................... 14-5
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG
LAMP ............................... 8L-9
UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP ....8L-15
UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP .........8L-9
UNIT ALIGNMENT - STANDARD PROCEDURE, HEADLAMP ..............8L-14
UNIT FLUID - DESCRIPTION, AWD POWER TRANSFER .....................0-6
UNIT TRACK & RACK - DESCRIPTION, LOWER DRIVE ...................... 8N-57
UNIT TRACK & RACK - INSTALLATION, LOWER DRIVE ...................... 8N-58
UNIT TRACK & RACK - OPERATION, LOWER DRIVE ...................... 8N-57UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE ...................... 8N-57
UNIVERSAL TRANSMITTER - DESCRIPTION ....................... 8M-11
UNIVERSAL TRANSMITTER, DIAGNOSIS AND TESTING ....................... 8M-11
UPPER - INSPECTION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, INTAKE MANIFOLD ........................... 9-61
UPPER - INSTALLATION, SHROUD .......19-22
UPPER - REMOVAL, INTAKE MANIFOLD ....9-60
UPPER - REMOVAL, SHROUD ...........19-22
UPPER HINGE - INSTALLATION .........23-36
UPPER HINGE - REMOVAL .............23-36
UPPER INTAKE MANIFOLD - INSTALLATION ....................... 9-149
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-148
UPPER RADIATOR CROSSMEMBER - INSTALLATION ....................... 23-56
UPPER RADIATOR CROSSMEMBER - REMOVAL .......................... 23-56
UPPER TRIM - INSTALLATION, B-PILLAR . . 23-80
UPPER TRIM - REMOVAL, B-PILLAR .....23-80
UPSTREAM 1/1 - 2.4L - INSTALLATION . . . 14-38
UPSTREAM 1/1 - 2.4L - REMOVAL .......14-37
UPSTREAM 1/1 - 3.3/3.8L - INSTALLATION ....................... 14-39
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL ....14-38
USE WIRING DIAGRAMS - DESCRIPTION, HOW TO .............8W-01-1
USING PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING
CLEARANCE ..................... 9-12,9-86
VAC LEAK DETECTION ASSY - INSTALLATION, NATURAL ..............25-14
VAC LEAK DETECTION ASSY - REMOVAL, NATURAL .................. 25-14
VACUUM PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD ........9-148
VACUUM RESERVOIR - DESCRIPTION .....8P-6
VACUUM RESERVOIR - INSTALLATION ....8P-6
VACUUM RESERVOIR - OPERATION .......8P-6
VACUUM RESERVOIR - REMOVAL ........8P-6
VALVE - DESCRIPTION ................25-23
VALVE - DESCRIPTION, A/C EXPANSION . 24-100
VALVE - DESCRIPTION, EXPANSION ......24-81
VALVE - DESCRIPTION, PCV ............25-18
VALVE - INSTALLATION, OIL PRESSURE RELIEF ............................. 9-144
VALVE - OPERATION ..................25-23
VALVE - OPERATION, A/C EXPANSION . . . 24-100
VALVE - OPERATION, EXPANSION .......24-81
VALVE - OPERATION, PCV ..............25-18
VALVE - REMOVAL, OIL PRESSURE RELIEF ............................. 9-143
VALVE BODY - ASSEMBLY ......21-139,21-291
VALVE BODY - DESCRIPTION ....21-132,21-283
VALVE BODY - DISASSEMBLY ....21-135,21-286
VALVE BODY - INSTALLATION ....21-144,21-295
VALVE BODY - OPERATION ......21-132,21-283
VALVE BODY - REMOVAL .......21-133,21-284
VALVE CORE - DESCRIPTION, SERVICE PORT.............................. 24-95
VALVE CORE - INSTALLATION, SERVICE PORT.............................. 24-95
VALVE CORE - REMOVAL, SERVICE PORT.............................. 24-95
VALVE, DESCRIPTION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE, DIAGNOSIS AND TESTING - FRONT A/C EXPANSION ...............24-82
VALVE, DIAGNOSIS AND TESTING - REAR A/C EXPANSION ...............24-101
VALVE (HEIGHT SENSING) - DESCRIPTION, PROPORTIONING .........5-53
VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING, PROPORTIONING .........5-54
VALVE (HEIGHT SENSING) - INSTALLATION, PROPORTIONING .........5-55
VALVE (HEIGHT SENSING) - OPERATION, PROPORTIONING ..................... 5-53
VALVE (HEIGHT SENSING) - REMOVAL, PROPORTIONING ..................... 5-55
VALVE, OPERATION - HIGH PRESSURE RELIEF ............................. 24-72
VALVE SEATS - STANDARD PROCEDURE, REFACING VALVES ................... 9-107VALVE SPRINGS - DESCRIPTION
........9-109
VALVE SPRINGS - OPERATION ..........9-109
VALVE STEM SEALS - DESCRIPTION .....9-114
VALVE STEM SEALS - INSTALLATION .....9-115
VALVE STEM SEALS - REMOVAL ........9-115
VALVE TIMING VERIFICATION - STANDARD PROCEDURE ...............9-155
VALVES - OPERATION, HYDRAULIC CIRCUITS ............................ 5-95
VALVES & SEATS - CLEANING, INTAKE/EXHAUST ................ 9-108,9-33
VALVES & SEATS - DESCRIPTION, INTAKE/EXHAUST ................ 9-107,9-33
VALVES & SEATS - INSPECTION, INTAKE/EXHAUST .................... 9-108
VALVES & SEATS - INSTALLATION, INTAKE/EXHAUST .................... 9-109
VALVES & SEATS - OPERATION, INTAKE/EXHAUST .................... 9-107
VALVES & SEATS - REMOVAL, INTAKE/EXHAUST .................... 9-108
VALVES AND VALVE SEATS - STANDARD PROCEDURE, REFACING ...............9-107
VANITY LAMP - INSTALLATION .........8L-24
VANITY LAMP - REMOVAL .............8L-24
VAPOR CANISTER - DESCRIPTION .......25-19
VAPOR CANISTER - OPERATION .........25-19
VARIABLE BRAKE PROPORTIONING - DESCRIPTION, ELECTRONIC .............5-88
VARIABLE BRAKE PROPORTIONING - OPERATION, ELECTRONIC ................5-89
VARIATION ADJUSTMENT, STANDARD PROCEDURE - COMPASS ...............8M-5
VEHICLE DOES NOT FILL - DIAGNOSIS AND TESTING ....................... 25-17
VEHICLE EMISSION CONTROL INFORMATION LABEL, DESCRIPTION ......25-1
VEHICLE IDENTIFICATION - DESCRIPTION ........................ 23-1
VEHICLE INFO CENTER - DESCRIPTION, ELECTRONIC ........................ 8M-7
VEHICLE INFO CENTER - OPERATION, ELECTRONIC ........................ 8M-7
VEHICLE INFORMATION CENTER, DIAGNOSIS AND TESTING -
ELECTRONIC ........................ 8M-8
VEHICLE INFORMATION CENTER PROGRAMMING, STANDARD
PROCEDURE - ELECTRONIC ............8M-8
VEHICLE THEFT SECURITY - DESCRIPTION ........................ 8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
VENT WINDOW MOTOR, DIAGNOSIS AND TESTING ....................... 8N-62
VERIFICATION - STANDARD PROCEDURE, VALVE TIMING ...........9-155
VIBRATION - DIAGNOSIS AND TESTING, TIRE AND WHEEL ..................... 22-1
VIBRATION DAMPER - INSTALLATION ....9-132,
9-49
VIBRATION DAMPER - REMOVAL ....9-132,9-48
VIDEO SCREEN - DESCRIPTION .........8A-20
VIDEO SCREEN - INSTALLATION ........8A-20
VIDEO SCREEN - OPERATION ...........8A-20
VIDEO SCREEN - REMOVAL ............8A-20
VIEW MIRROR - INSTALLATION, REAR . . . 23-97
VIEW MIRROR - INSTALLATION, SIDE ....23-60
VIEW MIRROR - REMOVAL, REAR .......23-97
VIEW MIRROR - REMOVAL, SIDE ........23-60
VISOR - INSTALLATION, SUN ...........23-99
VISOR - REMOVAL, SUN ...............23-99
VISOR SUPPORT - INSTALLATION, SUN . . . 23-99
VISOR SUPPORT - REMOVAL, SUN ......23-99
VOLT SUPPLY - PCM OUTPUT - OPERATION, 5 ....................... 8E-15
VOLTAGE DROP - STANDARD PROCEDURE, TESTING FOR A .......8W-01-10
VOLTAGE POTENTIAL - STANDARD PROCEDURE, TESTING OF ...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION ....8F-30
VOLTAGE REGULATOR - OPERATION .....8F-30
VOLTAGE TEST, STANDARD PROCEDURE - OPEN-CIRCUIT ..................... 8F-13
VTSS/SKIS INDICATOR LAMP - DESCRIPTION ........................ 8Q-8
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page