2005 CHEVROLET SSR lock

4. To install the new wiper insert, slide the insert (D),
notched end last, into the end with two blade
claws (A). Slide the insert all the way through the
blade claws at the opposite end (B). The plastic
caps (C) will be forced off as the insert is fully
inserted.
5. Be sure that the notches are locked by the bottom
claws. Make sure that all other claws are properly
locked on both sides of the insert slots.A. Claw in Notch
B. Correct Installation
C. Incorrect Installation
6. Put the blade assembly pivot in the wiper arm
hook. Pull up until the pivot locking tab locks in
the hook slot.
7. Carefully lower the wiper arm and blade assembly
onto the windshield.
5-51

Tire Sealant
The kit contains a liquid sealant that when injected into
a at tire, may temporarily repair nail holes or cuts
in the tread area of the tire. The tire sealant cannot
repair tire damage caused while driving on a at tire or
a tire that has had a “blow out” or a tire that has
punctures in the sidewall areas. The tire sealant solution
is a one-time use application for one tire only. Check
the tire sealant expiration date; the sealant may not be
as effective beyond the expiration date. The tire
sealant can be peeled off easily after drying.
Using Tire Sealant
To apply the tire sealant, do the following:
1. Turn the valve cap on the tire valve
counterclockwise to remove it.
2. Remove the valve core using the valve core tool
provided in the tire inator kit. An extra valve
core is also provided in the kit.
3. Shake the bottle to make sure the sealant is
well mixed.4. Attach the tire sealant lling hose to the bottle
of tire sealant to pierce the seal on the bottle.
5. Remove the sealing plug from the end of the
lling hose and insert the end of the hose over
the tire valve.
6. Hold the bottle upside down over the tire valve
and squeeze the sealant into the tire until the
bottle is empty.
7. Remove the sealant lling hose from the tire valve
and reinstall the sealing plug.
8. Insert the valve core back into the tire valve.
Turn the valve core tool clockwise to secure
the valve core.
Once the tire sealant is applied, you can use the
compressor to inate the tire. SeeAir Compressor on
page 5-70for instructions.
5-69

6. Inate the tire for
up to a maximum
of six minutes.
Notice:If 26 psi (179 kPa) tire pressure cannot be
reached after six minutes the vehicle should not
be driven farther. Damage to the tire is severe and
the sealant will not be effective. Remove the air
compressor plug from the accessory power outlet
and unscrew the inating hose from the tire
valve. SeeRoadside Assistance Program on
page 7-6.
7. If 26 psi (179 kPa) tire pressure is reached in
six minutes or less, disconnect or turn off the
air compressor.8. Attach the enclosed
maximum speed label
to the inside upper
left corner of the
windshield or to the
face of the radio/clock.
The maximum speed label reminds you to drive
cautiously and not to exceed 55 mph (90 km/h) until
you have the damaged tire inspected and repaired.
9. Drive the vehicle immediately to distribute the tire
sealant evenly inside the tire.
10. After driving for 10 minutes, recheck the tire
pressure. If the tire pressure is 19 psi (131 kPa) or
more, inate the tire to the standard operating
pressure as shown on the Certication/Tire label
located on the edge of the driver’s door.
If the tire pressure has dropped below 19 psi
(131 kPa), do not continue to drive the vehicle.
The tire is severely damaged and the tire sealant
will not be effective. Repair or replace the tire
as soon as possible.
5-73

Floor Console Fuse Block
The oor console fuse
block is located on
the console between
the two seats, on the
passenger’s side.To remove the fuse block cover and access the fuses,
do the following:
1. Move the passenger’s seat all the way forward and
tilt the seatback forward. SeePower Seats on
page 1-2andSeatback Latches on page 1-6for
more information.
2. Pull the handle on the fuse block cover toward you
and then slide it to the side. You will then be able
to remove the cover completely.
3. To reinstall the cover, slide it to the side until it is
lined up with the access hole. Then, push on the
fuse panel cover until it latches into place.
5-85

Fuses Usage
03 Rear Window Defogger
04 Truck Body Controller
05 Rear Window Defogger
06 Driver Seat Module
07 Truck Body Controller
09 Blank
10 Driver’s Door Module, Power Mirrors
11 Amplier
12 Blank
13 Daytime Running Lamps (DRL)
14 Driver’s Side Rear Parking Lamp
16 Center High-Mounted Stop Lamp
17Passenger’s Side Rear
Parking Lamp
19 Blank
20 Blank
21 Locks
22 Blank
23 Blank
25 Blank
5-86

Fuses Usage
26 Blank
27 HomeLink
®System
28 Roof Door Module
29 Transmission Control Module
31 Truck Body Controller
32 Remote Keyless Entry (RKE)
33 Windshield Wipers
34 Stoplamps
35 Blank
36Climate Control System,
Driver’s Door Unlock
37 Front Parking Lamps
38 Driver’s Side Turn Signal
39 Climate Control System
40 Truck Body Controller
41 Radio
42 Trailer Parking Lamps
43 Passenger’s Side Turn Signal
44 Blank
46 Accessory Power Outlets
Fuses Usage
47 Ignition
48 Blank
49 Blank
50 Truck Body Controller, Ignition
51 Brakes
52 Blank
Relays Usage
18 Locks
24 Unlock
30 Parking Lamps
45Rear Window Defogger,
Outside Power Heated Mirrors
Circuit
BreakersUsage
01 Roof & Door Module
02 Roof Pump
08 Power Seats
5-87

Engine Compartment Fuse Block
The fuse block is located
under the hood in the
engine compartment on
the driver’s side of
the vehicle. SeeEngine
Compartment Overview
on page 5-12for more
information on location.To remove the fuse block cover and access the fuses,
do the following:
1. To remove the primary fuse block cover, press in
on the two locking tabs and then lift the cover off.
2. Lift up on the secondary cover to remove it.
3. Reverse the steps to reinstall the covers.
5-88

Fuses Usage
25Automatic Transmission Shift
Interlock Control System
26 Back-up lamps, Lock Out
27 Engine Control Module
28 Oxygen Sensor B
29 Injector B
30 Air Conditioning
31Engine Control Module (ECM),
Transmission Control Module (TCM)
32 Transmission
33 Engine 1
34Engine Control Module,
Electronic Brake Controller
35 Oxygen Sensor A
36 Injector A
37 Engine Cooling Fan
38 Anti-lock Brake System (ABS)
39 Ignition A
40 Climate Control Fan
41 Ignition BRelays Usage
42 Powertrain
43 Starter
44 Fuel Pump
45 Cargo Cover Release
46 Windshield Washer
47 Headlamp Driver Module (HDM)
48 Fog Lamps
49 High Beam Headlamps
50 Horn
51 Air Conditioning
Miscellaneous Usage
52 Instrument Panel Battery
5-90