2005 CHEVROLET CAVALIER clock

4. Remove the cover
by turning it
counterclockwise.
5. Disconnect the bulb
base from the socket
by lifting the plastic
locking tab.
6. Remove the black collar by turning it clockwise.7. Remove the bulb by
pulling it straight out.
8. Snap a new bulb into the socket.
9. Reinstall the bulb assembly by reversing
Steps 1 through 6.
5-43

Front Turn Signal and Parking
Lamps
To replace a front turn signal or parking lamp bulb,
do the following:
1. Follow Steps 1 through 3 underHeadlamps on
page 5-42.
2. Hold down the tab
at the top of the
bulb retainer.
Twist the retainer
one-eighth of a turn
counterclockwise
and pull the
assembly out.
3. Remove the bulb by pulling the bulb straight out.
4. Snap in a new bulb.
5. Reinstall the bulb assembly by reversing
Steps 1 and 2.
Taillamps and Turn Signal Lamps
To replace a taillamp or rear turn signal bulb,
do the following:
1. Remove the fastener which holds down the
trunk trim.
On vehicles without a convenience net, pry the
fastener loose. On vehicles with a convenience net,
remove the net and unscrew the fastener. Then
pull down the trunk trim. SeeConvenience Net on
page 2-35for more information.
5-44

2. Remove the taillamp bulb socket by turning it
one-eighth of a turn counterclockwise.
3. Pull the old bulb out of the socket.
4. Push in a new bulb.
5. Reverse Steps 1 through 2 to reinstall.
Back-Up Lamps
To replace a back-up lamp bulb, do the following:
1. Open the trunk lid and locate the back-up lamp
assembly on the trunk lid.
2. Remove the bulb from the socket by turning it
counterclockwise and pulling it out.
3. Replace the bulb in the socket by aligning the tabs
and turning the bulb clockwise.
Replacement Bulbs
Exterior Lamps Bulb Number
Back-Up Lamps 3057
Front Parking/Turn Signal Lamps 3357K
Halogen Headlamps,
High/Low-Beam9007
Taillamp/Turn Signal Lamps 3057
For replacement bulbs not listed here, please consult
your dealer.
5-45

When you have a at tire, use the following example
as a guide to assist you in the placement of wheel
blocks.
The following information will tell you how to use the
jack and change a tire.Removing the Spare Tire and Tools
The equipment you will need is located in the trunk.
1. Turn the center retainer
nut on the compact
spare tire cover
counterclockwise to
remove it.
5-63

2. Lift and remove the cover. SeeCompact Spare
Tire on page 5-71for more information about the
compact spare tire.3. Turn the wing bolt
counterclockwise and
remove it. Then lift
off the adapter
and remove the
compact spare tire.
4. Remove the jack and wheel wrench from the trunk,
which are stored in the foam tray. Remove the
band around the jack.
5-64

6. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the compact
spare tire to t underneath the wheel well.
7. Remove all of the wheel nuts.
{CAUTION:
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel nuts
become loose after a time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
the places where the wheel attaches to the
vehicle. In an emergency, you can use a cloth
or a paper towel to do this; but be sure to use
a scraper or wire brush later, if you need to,
to get all the rust or dirt off.
8. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces and spare
wheel.
5-67

9. Place the compact spare tire on the wheel-mounting
surface.
{CAUTION:
Never use oil or grease on studs or nuts. If
you do, the nuts might come loose. Your wheel
could fall off, causing a serious accident.
10. Reinstall the wheel nuts with the rounded end of
the nuts toward the wheel.11. Tighten each nut by hand until the wheel is held
against the hub.
12. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
5-68