2005 Alfa Romeo GT light

GETTING TO KNOW YOUR CAR
104
AIR TEMPERATURE
ADJUSTMENT KNOB
Turn the ring of knob (1-fig. 95) clock-
wise or counter-clockwise respectively to
higher or lower the temperature of the air
admitted to the passenger compartment.
AIRDISTRIBUTION KNOB
Turning the knob ring (3-fig. 95), the
following positions are selected in sequence:
Air flow towards the upper centre,
front centre vents and from the front
and rear outlets with the possibility of ad-
justment using the controls on the actual
vents.
Splitting of air flow between the pre-
vious vents and the lower part of the
passenger compartment.
Air flow to the lower part of the pas-
senger compartment (front and rear).
Splitting of air flow between the
windscreen/front side windows and
the lower part of the passenger compart-
ment.
Air flow towards the windscreen and
front side windows for demist-
ing/defrosting.
Flow air to allow quick demist-
ing/defrosting of the windscreen
and front side windows, turning on
rearscreen heating for defrosting/demisting
(function called
MAX-DEF).
μ
w
≤
y
-
¥
FAN SPEED ADJUSTMENT
KNOB
Turning the ring of knob (2-fig. 95) it is
possible to select one of the fan speeds to per-
sonalise the amount of air admitted to the pas-
senger compartment.
Position0turns off the fan and automati-
cally engages inside air re-circulation (shown
by the lighting up of the led next to the but-
ton4
v) thereby shutting off the inlet of
outside air to the car.
To switch off inside air re-circulation, press
button (4)
v.

GETTING TO KNOW YOUR CAR
105
INSIDE AIR RE-CIRCULATION
ON/OFF BUTTON
Pressing button (4-fig. 95)vacti-
vates inside air re-circulation and the led next
to the button lights up.
In this case the climate control system di-
rectly treats the air contained in the pas-
senger compartment, the fan is on.
To switch the air re-circulation feature off
and withdraw air from outside, press the but-
ton again.The inside air- re-circula-
tion system makes it pos-
sible to reach the required
“heating” or “cooling” conditions
faster. It is however inadvisable to
use it on rainy/cold days as it
would considerably increase the
possibility of the windows misting
inside, especially if the climate con-
trol system is off.
It is advisable to turn on
the inside air re-circulation
system
vin queues or
tunnels to avoid admitting pollut-
ed air from outside. The prolonged
use of this function should howev-
er be avoided, especially with sev-
eral persons on board, to avoid the
possibility of the windows misting
inside.
REARSCREEN HEATING
ON/OFF BUTTON
Pressing the button (5-fig. 95) turns on
demisting/defrosting of the rearscreen, and
if present, the wing mirror heating coils; si-
multaneously the led next to the button
turns on. This function is timed and switched
off automatically after 20 minutes. To turn
off earlier, press the button again.
IMPORTANTThe system automatically
turns on rearscreen heating if the tempera-
ture is below 3
°C.
IMPORTANTDo not apply stickers on
the inside of the rearscreen over the heat-
ing filaments to avoid damage which might
cause it to stop working properly.
When cleaning the inside
of the rearscreen, take
care not to damage the
heating filaments.

GETTING TO KNOW YOUR CAR
118
press button (13)AUTO; in which case,
however, the other manual settings set will
be cancelled.
CLIMATE CONTROL
COMPRESSORON/OFF ENABLE
BUTTON
(fig. 108)
Pressing button (14)
√enables the turn-
ing on of the climate control compressor.
This condition is shown by the lighting up of
the led on the button itself.
When the climate control compressor is
turned off, the leds on buttons (13)
AUTO
and (14)√go off; automatic inside air re-
circulation control is also excluded (both leds
off on button 8
v) which always stays
off to prevent misting the windows; even
if unadvisable, it is still possible to restore
automatic operation of inside air re-circula-
tion pressing button (8)
v.
With the climate control compressor off, it
is not possible to admit air to the passenger
compartment with a temperature
below the outside temperature; in this case,
the value flashes on the display concerning
the temperature that cannot be reached and
the left led on button (13
AUTO- fig.
109) goes off.
The switching off of the climate control
compressor remains in storage even when
the engine has been stopped. To restore au-
tomatic control for switching on the climate
control compressor, press button (14)
√again, the led on the button turns on, or
Operation of the climate
control compressor is neces-
sary for cooling and dehu-
midifying the air; it is advisable to
keep this function always on, to pre-
vent window misting problems.
A0A0210b
A0A0211bfig. 108
fig. 109

GETTING TO KNOW YOUR CAR
120
It is advisable to turn on
the inside air re-circulation
system in queues or tun-
nels to avoid admitting polluted air
from outside. The prolonged use of
this function should however be
avoided, especially with several
persons on board, to avoid the pos-
sibility of the windows misting in-
side.
AUTOMATIC OPERATION AUTO
BUTTON
(fig. 111)
Pressing the (13)
AUTObutton the sys-
tem automatically adjusts the amount and
distribution of the air admitted to the pas-
senger compartment, cancelling all the pre-
vious manual adjustments.
This condition is indicated by the lighting
up of both leds on the button itself.When the right led, on button (13)
AU-
TOis off, this means that one or more man-
ual operations have been carried out and
therefore automatic control is not complete
(except temperature control which is always
automatic) indicated by the left led on, or
that the system is in the
OFFcondition. In certain weather condi-
tions (e.g.: outside tem-
perature around 0°C) and
with automatic air re-circulation
control on, mist may form on the
windows. In this case press the in-
side air re-circulation button (8)
v, to switch off re-circulation
(leds on button off) and if neces-
sary increase the flow of air to the
windscreen.
A0A0209b
fig. 111

GETTING TO KNOW YOUR CAR
124
CONTROLS
TAILGATE OPENING (fig. 114)
Electric tailgate release is only allowed with
the ignition key in the ignition switch at
MARvehicle stationary, at STOPor
PARK for 3 minutes without opening/clos-
ing a door. To release the tailgate, press but-
ton (A) on the centre console panel.
Use the hazard warning
lights in compliance with
local regulations.
FOG LIGHTS (fig. 114)
These are turned on pressing button (B),
on the centre console panel, when the out-
er lights are already on, at the same time
the led on the button itself turns on.
Turning the ignition key to STOPthe fog
lights are turned off automatically and do
not come on the next time the engine is
started without pressing button (B).
Press button (B) again to switch off.
IMPORTANTThe front foglights should
be used in compliance with local traffic laws.
fig. 114
A0A0091b
HAZARD WARNING LIGHTS
(fig. 114)
These are switched on by pressing button
(C), on the centre console panel, regardless
of the position of the ignition key.
When the hazard warning lights are
switched on, the switch itself begins to flash
together with the direction indicators and
the direction indicator warning lights on the
instrument cluster. This function is switched
off by pressing the button again.

GETTING TO KNOW YOUR CAR
125
If no leaks are found the vehicle can be
restarted. Press button (A) to activate the
fuel supply system again.
fig. 115
A0A0092b
If a smell of fuel is noted
following an accident, or
the fuel system is leaking,
to avoid the risk of fire do not re-
set the switch.REAR FOG GUARDS (fig. 114)
These are turned on, with the dipped beam
headlights or fog lights on, pressing button
(D) on the centre console panel, at the
same time the warning light on the button
itself turns on.
Turning the ignition key to STOPthe fog
guards are automatically turned off and they
do not come on the next time the engine
is started unless button (D) is pressed. To
turn them off press button (D).
IMPORTANTAlways use the rear fog
guards in compliance with local regulations.
DOOR LOCKING SYSTEM
(fig. 114)
To lock the doors simultaneously, press but-
ton (E), on the centre console panel, re-
gardless of the position of the ignition key.
The deterrent led turns on as follows:
– with the ignition key at MARglowing
steadily with a yellow light;
– with the ignition key at STOPflash-
ing with a red light (deterrence condition).
INERTIAL FUEL CUT-OFF
SWITCH
(fig. 115)
This is an automatic safety switch, to be
found on the floor next to the driver’s door
pillar, which is triggered in the event of a
crash of a certain magnitude to interrupt the
flow of fuel.
The cutting in of the inertial switch is shown
on the display of the instrument cluster.

GETTING TO KNOW YOUR CAR
126
The adjustment of Xenon headlights is au-
tomatic, therefore the versions fitted with
this optional lack the headlight aiming de-
vice (fig. 116a).
HAND BRAKE(fig. 117)
The hand brake lever is located between
the two front seats.
To operate the brake when the vehicle is
stationary, pull lever (A) upwards, until the
required braking action is obtained.
When the ignition key is at MAR, the
warning light on the instrument cluster
x
will come on.
fig. 117
A0A0620b
fig. 116a versions with Xenon headlights
A0A0677b
Adjust the beams every
time the load carried
changes.
For correct adjustment, bear in mind the
following conditions:
– position 0: one or two people occupy-
ing the the front seats
– position 1: five people;
– position 2: five people + load in the
boot;
– position 3: driver + maximum permis-
sible load all stowed in lug-
gage compartment
fig. 116 versions without Xenon headlights
A0A0093b
HEADLIGHT AIMING DEVICE
(fig. 116)
The headlights should be aimed correctly
depending on the vehicle load.
To do this, use the rocker button (A), on
the plate at the side of the steering column:
– press the arrow on the button (
A), to
increase by one position (e.g.:0
➟1➟2➟
3);
– press the arrow on the button (
S), to lower
by one position (e.g.:3
➟2➟1➟0);
The display (B) in the tachometer shows the
positions during adjustment.

GETTING TO KNOW YOUR CAR
127
To release the hand brake:
– slightly lift the lever (A) and press the
release button (B);
– keeping the button pressed lower the
lever, the warning light
xon the instru-
ment cluster will go out.
To prevent the car from moving acciden-
tally, keep the brake pedal pressed when
engaging the hand brake.
IMPORTANTThe hand brake lever (A)
is fitted with a safety device which prevents
the brake from being released when, with
the lever pulled, button (B) is pressed.
Therefore, to release the brake, in addition
to pressing button (B), it is also necessary
to pull lever (A) further upwards to release
the safety device, then lower the lever com-
pletely.
IMPORTANTOn certain versions a
buzzer sounds to alert the driver if the car
is moved with the hand brake engaged.
GEARSHIFT LEVER (fig. 118)
The position of the single gears is shown
by the pictogram on the gearshift lever
knob.
When shifting gear, always fully depress
the clutch pedal. Before engaging reverse
gear (R) wait for the car to be stationary.
Certain versions are fitted with 6-gear gear-
box.
IMPORTANTReverse gear may only be
engaged with the car completely at a stand-
still. With the engine running, before en-
gaging reverse gear it is necessary to wait
for at least 3 seconds with the clutch pedal
fully depressed to prevent clashing and the
possibility of damaging the gears. The wheels should be
locked after a few clicks of
the hand brake. If it does
not occur contact Alfa Romeo Au-
thorised Services to have the hand
brake adjusted.To change gear smoothly,
the clutch pedal must be
fully depressed. Therefore,
there should be no obstacles on the
floor under the pedal unit: make
sure that any mats are well laid
and do not interfere with the ped-
als.
fig. 118
A0A0684b