2005 Alfa Romeo GT wheel

IN AN EMERGENCY
214
CHANGING A WHEEL
Please be informed that:
– the jack mass is 2,100 kg.
– the jack requires no adjustment.
– the jack cannot be repaired. In the
event of breakage, it must be replaced by
another original one.
– no tools other than its operating crank
can be fitted to the jack.
To change a wheel, proceed as follows:– Stop the car in such a position that it
is not dangerous for the traffic, where it is
possible to change the wheel safely.
Where possible, park on a level, compact
surface.
– Switch off the engine and engage the
handbrake.
– Engage first gear or reverse.– Use handle(A-fig.2) to remove the
stiff covering (B).
– Loosen the clamping device (A-
fig. 3).
– Take out the tool container (B) and
take it near the wheel to be changed.
– Take the spare wheel (C).
– Remove the wheel cap (A-fig. 4)
(only versions with steel rims)
fig. 2
A0A0645b
fig. 3
A0A0151b
fig. 4
A0A0154b

IN AN EMERGENCY
215
– Using the wrench provided (A-
fig. 5), loosen the fastening bolts by
about one turn.
– Set the jack under the car, near the
wheel to be changed taking care not to
damage the plastic streamlined guard.
– Work the jack crank (A-fig. 6), to
extend it until the groove (B) on the
upper part of jack is correctly inserted on
the lower profile of the body (C) approx.
40 cm from the profile of the wheelhouse.
– Work the jack and raise the car until
the wheel is a few centimetres from the
ground.
– Completely unscrew the fastening
bolts and remove the wheel.– Make sure that the contact surfaces of
the spare wheel with the hub are clean
and free of impurities which may later
cause the fastening bolts to slacken.
– Install the spare wheel matching the
hole (A-fig. 7) with the corresponding
pin (B).
– Using the wrench provided, fasten the
five bolts.
– Lower the car and remove the jack.
– Using the wrench provided, fully tighten
the bolts in the sequence shown in fig. 8.REFITTING A NORMAL WHEEL
– Following the procedure described
previously, raise the car and remove the
spare wheel.
For versions with steel rims:
– Fit the normal wheel matching the
hole (A-fig. 7) with the corresponding
pin (B).
– Make sure that the contact surfaces of
the wheel with the hub are clean and free
of impurities which may later cause the
fastening bolts to slacken.
fig. 5
A0A0694b
fig. 6
A0A0695b

IN AN EMERGENCY
216
– Using the wrench provided, tighten
the fastening bolts.
– Lower the car and remove the jack.
– Using the wrench provided, fully tight-
en the bolts in the sequence shown previ-
ously for the compact spare wheel fig. 8.
– Place the cap near the wheel so that
the inflation valve can come through the
slot provided on the cap.
– Press the circumference of the cap,
starting from the parts nearest to the infla-
tion valve until it is inserted completely.
IMPORTANTIncorrect fitting may
cause the wheel cap to come off when the
car is travelling.For versions with alloy rims:
– Tighten the pin (A-fig. 9) in one of
the fastening bolt holes on the wheel hub.
– Insert the wheel on the pin and, using
the wrench provided, tighten the four bolts
available. This is facilitated by the exten-
sion provided (B).
– Remove the pin (A-fig. 9) and tight-
en the last fastening bolt.
– Lower the car and remove the jack.
– Using the wrench provided, tighten
the bolts in the sequence shown previous-
ly for the compact spare wheel fig. 8.After refitting a wheel:
– stow the spare wheel in the space pro-
vided in the boot
– insert the jack in its container forcing
it lightly to prevent it from vibrating when
travelling
– place the tools used in the housings in
the container
– stow the container complete with tools
on the spare wheel and secure everything
with the clamping device (A-fig. 3)
– correctly re-position the stiff cover.
fig. 7
A0A0155b
fig. 8
A0A0156b
fig. 9
A0A0693b

IN AN EMERGENCY
217
QUICK TYRE REPAIR
KIT FIX&GO automatic
The car is provided with the quick tyre re-
pair kit “FIX&GO automatic”, instead of the
traditional tool kit and space-saver spare
wheel.
The kit fig. 10, is placed in the boot. In
this container are also housed the screw-
driver and the tow hitch. The quick tyre repair kit includes:
– a bottle A-fig. 10containing the seal-
er, fitted with:
– filling pipe B
– sticker Cbearing the notice “max. 80
km/h”, to be placed in a position visible
to the driver (on the instrument panel) af-
ter fixing the tyre;
– compressor Dwith pressure gauge and
fittings;– instruction brochure fig. 11, to be used
for prompt and proper use of the quick re-
pair kit and to be then handed to the per-
sonnel charged with handling the tyre treat-
ed with the tyre repair kit;
– a pair of protection gloves located in the
side space of the compressor;
– adapters for inflating different elements.
fig. 10
A0A1095b
fig. 11
A0A1096b

IN AN EMERGENCY
218
Hand the instruction
brochure to the personnel
charged with treating the
tyre repaired with the kit.
In the event of a puncture
caused by foreign bodies,
it is possible to repair tyres
showing damages on the track or
shoulder up to max 4 mm diame-
ter. IT SHOULD BE NOTICED THAT:
The sealing fluid of the quick tyre repair kit
is effective with external temperatures be-
tween –20°C and +50°C. The sealing flu-
id has limited life.
Holes and damages on
the tyre side walls cannot
be repaired. Do not use the
quick tyre repair kit if damaging
is due to running with flat tyre.
Repairs are not possible
in case of damages on the
wheel rim (bad groove dis-
tortion causing air loss). Do not re-
move foreign bodies (screws or
nails) from the tyre.The cylinder contains eth-
ylene glycol. The cylinder
contains latex: it can cause
allergic reactions. It is harmful if in-
gested or inhaled and irritant for
the eyes and in case of contact. In
case of contact rinse immediately
with water and take off contami-
nated clothes. If swallowed, do not
induce vomit, rinse out the mouth,
drink a lot of water and call the
doctor immediately. Keep away
from children. This product must
not be used by asthmatics. Do not
inhale vapours. Call the doctor im-
mediately in case of allergic reac-
tions. Keep the cylinder in the
space provided for the purpose and
far from heat. The sealing fluid has
limited life.

IN AN EMERGENCY
219
The compressor shall not
be operated for more than
20 minutes. Risk of over-
heating!. Tyres repaired with the
quick tyre repair kit shall be used
temporarily only.
Replace the cylinder if
sealer has run out. Do not
throw away the cylinder
and the sealing fluid. Have the
sealing fluid and the cylinder dis-
posed of in compliance with na-
tional and local regulations.INFLATING PROCEDURE
Put on the protection
gloves provided together
with quick tyre repair kit.
Proceed as follows:
– set the wheel to be repaired with valve
A-fig. 13in the position shown in the fig-
ure, then pull up the handbrake, take
the quick tyre repair kit and put it on the
ground near the wheel to be repaired;– loosen tyre inflation valve cap, take out
the filler hose A-fig.1 4and screw the ring
nutB-fig. 15on the tyre valve;
fig. 13
A0A1097bfig. 14
A0A1098b
fig. 15
A0A1099b

IN AN EMERGENCY
244
IF THE VEHICLE IS TO BE TOWED
The tow ring supplied with the vehicle is
housed in the tool box under the boot
mat.
To install the tow ring, proceed as fol-
lows:
– Take the tow ring from the tool box.
– Remove the cover (A) snap-fitted on
the front (fig. 55) or rear (fig. 56)
bumper. To do this, using the flat-bladed
screwdriver provided, protect the tip with
a soft cloth to avoid damaging the car.– Firmly screw the ring in its housing.
fig. 55 - front
A0A0650b
fig. 56 - rear
A0A0670b
Before tightening the
ring carefully clean the
threaded housing. Before
beginning to tow the car, make
sure that the ring is firmly tight-
ened in its threaded housing.
Before starting to tow,
turn the ignition key to
MAR and back to STOP,
again without removing it.
Removing the key automatically
engages the steering lock result-
ing in the impossibility to steer
the wheels. When towing
remember that without the help
of the engine brake and power
steering greater effort is required
on the pedal and steering wheel.
Do not use flexible cables for
towing and avoid jerks. During
towing operations make sure
that fastening the joint to the car
does not damage the components
in contact with it. When towing
the car, it is compulsory to follow
specific traffic regulations con-
cerning both the towing device
and behaviour on the road.

IN AN EMERGENCY
245
Take care when position-
ing the arms of the lift or
workshop lift to avoid
damaging the side strips.
USING AN ARM LIFT OR
WORKSHOP LIFT
The vehicle should be lifted only at the
side, setting the end of the arms or the
workshop lift in the illustrated areas, at
approx. 40 cm from the wheelhouse pro-
file (fig. 57).These areas are highlighted by the sym-
bol
▼on the lower part of the side mem-
ber.
The car may fall if the
jack is not positioned cor-
rectly. Never use the jack
for higher capacities than the one
stated on the label.
IMPORTANTFor versions with
Selespeed transmission, make sure that
the gears are in neutral (N) (checking
that the vehicle moves if pushed) and
then proceed as for towing a normal car
with mechanical transmission, following
the instructions given previously.
Should it be impossible to set the gears
to neutral, do not tow the car and contact
Alfa Romeo Authorised Services.Do not start the engine
when towing the car.
IF THE VEHICLE IS TO BE LIFTED
fig. 57
A0A0672b