2005 Acura RL light

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to theupper end of the white section of the
gauge. If it reaches the red (hot)
mark, pull saf ely to the side of the
road. For more inf ormation, see page
. This shows how much f uel you
have. It may show slightly more
or less than the actual amount.
The needle returns to the
bottom after you turn off the
ignition.
345
Gauges
Temperature Gauge Fuel Gauge
68
U.S. model is shown.TACHOMETER SPEEDOMETER TEMPERATURE GAUGE
FUEL GAUGE
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.

ÛÝ
µ™´
µ™´¶
¶
With the multi-information display
and the , , and SEL/RESET
buttons on the right side of the
steering wheel, you can change
several vehicle control settings to
your pref erence (see page ).
To change the settings, the ignition
switch must be in the ON (II)
position.
Here are the settings you can
change: 81
CUST OMIZE MENU
ENGLISH
FRENCH
SPANISH5°F 5°F
3°C 3°C
ON
OFF
ON
OFF
ON
OFF
ALL DOORS
ON
OFF
ON
OFF
60 SEC
30 SEC
15 SEC
60 SEC
30 SEC
See page
83
See page
83
See page
84
See page
86
See page
86
See page
89
See page
89
See page
90
See page
92
See page
92
LANGUAGE
SELECTION
ADJUST OUTSIDE
TEMP. DISPLAY
TRIP A & AVG. FUEL A
RESET with REFUEL
EXIT
MEMORY POSIT ION
LINK
AUTO TILT &
TELESCOPIC
EXIT
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS
BEEP
EXIT
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O
OFF TIMER
MET ER SET UP
POSITION SETUP
KEYLESS ACCESS
SETUP
LIGHTING SETUP
DEFAULT
ENGLISH
0°F
0°C
OFF
ON
ON
ON
ON
30 SEC
15 SECCUST OMIZE SET UP
DRIVER DOOR ONLY
CUST OMIZE GROUP
DRIVER
DOOR ONLY
Multi-Inf ormation Display
Customized Settings
78

If you turn the ignition switch to
ACCESSORY (I) or LOCK (0), or
move the shift lever out of Park, the
display will change to the normal
screen.
To have the driver’s ID detected,
make sure your remote is linked to
the system (seeon page ). Then use your
remote to unlock the doors (see on page ).
When the ignition switch is in the
ON (II) position, the multi-
inf ormation display shows the driver’s
ID.
You cannot customize the setting; When the keyless memory
settings are of f (see page ).
When you disconnect the vehicle
battery, and then do not unlock
the door.
When the multi-information
display does not show the driver’s
ID. 86
88
167CUST OMIZE MENU 15 SEC
0SEC
MAX
HIGH
MID
LOW
MIN
SHIFT FROM P
WITH VEH SPD
OFF
SHIFT TO P
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 SEC
60 SEC
30 SEC
INTERMITTENT
WITH VEH SPDDEFAULT
15 SEC
MID
WITH VEH
SPD
SHIFT TO
P
DRIVER
DOOR
ON
30 SEC
WITH VEH
SPD
See page
92
See page
93
See page
95
See page
96
See page
97
See page
97
See page
98
See page
100
LIGHTING SETUP
DOOR/WINDOW
SETUP
WIPER SETUP
HEADLIGHT AUT O
OFF TIMER
AUTO LIGHT
SENSITIVITY
EXIT
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
SECURITY RELOCK
TIMER
EXIT
WIPER ACTION
EXIT
EXITCUST OMIZE SET UP
CUST OMIZE GROUP
KEYLESS LOCK
ACKNOWLEDGMENT
Multi-Inf ormation Display
Memory Position
Link
K eyless A ccess Setup
Inst rument s and Cont rols
79

Û
Ý
ÛÝ
Each time you press the INFO ( / ) button, the display changes as
shown in the illustration. Select
which of these customize groups you
want to change:
If you select EXIT and press the
SEL/RESET button, the
CUSTOMIZE ENTRY screen is
shown again. WIPER SET UP DOOR/WINDOW SET UP
LIGHTING SET UP
KEYLESS ACCESS SET UP
POSITION SET UP
METER SET UP
With the ignition switch in the ON
(II) position, press the INFO button
f or more than 3 seconds, then
release it. The CUSTOMIZE ENTRY
screen appears on the multi-
inf ormation display.
Select CHG SETTING, and press the
SEL/RESET button.
Multi-Inf ormation Display
Selecting a Customize Group
Inst rument s and Cont rols
81
Press the or button.
Press the SEL/RESET button. TO METER
SET UP
seepage82
TO POSITION
SET UP
seepage85
TO KEYLESS
ACCESS SET UP
seepage88
TO LIGHTING
SET UP
seepage91
TO DOOR/
WINDOW SET UP
seepage94
TO WIPER
SET UP
seepage99

Û
Ý
ÛÝ
Each time you press the INFO ( / ) button, the display changes as
shown in the illustration.
Here are the settings you can
customize in this mode: DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
If you select EXIT and press the
SEL/RESET button, the
CUSTOMIZE GROUP screen is
shown again. With the ignition switch in the ON
(II) position, press the INFO button
f or more than 3 seconds, then
release it. The CUSTOMIZE ENTRY
screen appears on the multi-
inf ormation display.
Select CHG SETTING, and press the
SEL/RESET button.
Select KEYLESS ACCESS SETUP,
and press the SEL/RESET button.
Multi-Inf ormation Display
K EYL ESS A CCESS Setup
88
Press the or button.
Press the SEL/RESET button.

ÛÝ
Door Unlock ModeKeyless Access Light FlashThe conf irmation screen is shown
f or 2 seconds, then the CUSTOMIZE
ENTRY screen returns.
To exit this mode without changing
the current settings, select EXIT,
and press the SEL/RESET button.
You can select whether the driver’s
door unlocks or all the doors unlock
when you unlock the doors by
grabbing the driver’s door handle
while carrying the remote.
Select the desired mode by pressing
the or button, and enter your
selection by pressing the SEL/
RESET button. When you unlock the doors by
grabbing the driver’s door handle
while carrying the remote, some
exterior lights will blink twice.
When you lock the doors touching
the door lock sensor while carrying
the remote, some exterior lights will
blink once.
You can turn this feature on or off.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
89

ÛÝ
ÛÝ
Each time you press the or
button, the screen changes as shown
in the illustration.
Here are the settings you can
customize in this mode:INTERIOR LIGHT
DIMMING TIME
HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
If you select EXIT and press the
SEL/RESET button, the
CUSTOMIZE GROUP screen is
shown again. With the ignition switch in the ON
(II) position, press the INFO button
f or more than 3 seconds, then
release it. The CUSTOMIZE ENTRY
screen appears on the multi-
inf ormation display.
Select CHG SETTING, and press the
SEL/RESET button.
Select LIGHTING SETUP, and press
the SEL/RESET button.
CONT INUED
Lighting Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
91
Press the or button.
Press the SEL/RESET button.

ÛÝÛ
Ý
Interior Light Dimming Time Headlight Auto Of f Timer
The interior lights f ade out when you
close all doors (see page ). Select
how long it takes f or the interior
lights to f ade out (in seconds) f rom
60 SEC, 30 SEC, or 15 SEC by
pressing the or button, and
enter your selection by pressing the
SEL/RESET button.Select how long it takes f or the
exterior lights to turn of f (in
seconds)from60SEC,30SEC,15
SEC,or0SEC,bypressingthe or
button, and enter your selection
by pressing the SEL/RESET button.
To exit this mode without changing
the current settings, select EXIT,
and press the SEL/RESET button.
The conf irmation screen is shown
f or 2 seconds, then the CUSTOMIZE
ENTRY screen returns. The headlights, parking lights, side
marker lights, taillights, and license
plate light turn of f af ter the selected
time when you close the driver’s
door and take the remote with you.
160
Multi-Inf ormation Display
92