2005 Acura RL ECU

CONT INUED
When not using the LATCH system,
all child seats must be secured to the
vehicle with the lap part of a lap/
shoulder belt.With the child seat in the desired
seating position, route the belt
through the child seat according
to the seat maker’s instructions,
then insert the latch plate into the
buckle.To activate the lockable retractor,
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt f eed back into the
retractor.
Af ter the belt has retracted, tug on
it. If the belt is locked, you will not
be able to pull it out. If you can pull
thebeltout,itisnotlocked,and
you will need to repeat these steps.
In addition, the lap/shoulder belts in
all seating positions except the
driver’s have a locking mechanism
that must be activated to secure a
child seat.
1.2.
3.
Installing a Child Seat
Installing a Child Seat with a L ap/
Shoulder Belt
Driver and Passenger Saf ety
47

To deactivate the locking
mechanism and remove a child seat,
unlatch the buckle, unroute the seat
belt, and let the belt f ully retract.
Push and pull the child seat
f orward and f rom side to side to
verif y that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract f ully, then repeat these
steps.
Af ter conf irming that the belt is
locked, grab the shoulder part of
the belt near the buckle, and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.
To remove slack, it may help to
putweightonthechildseat,or
push on the back of the seat while
pulling up on the belt. 5.
4.
Installing a Child Seat
48

A child seat with a tether can be
installed in any seating position in
the back seat, using one of the
anchorage points shown above.
Since a tether can provide additional
security to the lap/shoulder belt
installation, we recommend using a
tether whenever one is required or
available.Af ter properly securing the child
seat with the lap/shoulder belt
(see page ), pivot the head
restraint down (see page ) and
route the tether strap over the
head restraint.Lift the anchor cover, then attach
the tether strap hook to the
anchor, making sure the strap is
not twisted.
Tighten the strap according to the
seat maker’s instructions.
1. 2.
3.
47 120
Installing a Child Seat
Installing a Child Seat with a
TetherUsing t he T et her A nchor
Driver and Passenger Saf ety
49
COVER TETHER STRAP
HOOK
ANCHOR
ANCHOR
TETHER ANCHORAGE P
OINTS

If you decide that a child can saf ely
ride up f ront, be sure to:Caref ully read the owner’s manual,
and make sure you understand all
seat belt instructions and all saf ety
inf ormation.
Move the vehicle seat to the rear-
most position.
Have the child sit up straight, back
against the seat, and feet on or
near the f loor.
Check that the child’s seat belt is
properly and securely positioned.
Supervise the child. Even mature
children sometimes need to be
reminded to f asten the seat belts
or sit properly.
Of course, children vary widely. And
while age may be one indicator of
when a child can saf ely ride in f ront,
there are other important f actors you
should consider.
If the passenger’s f ront airbag
inf lates in a moderate to severe
f rontal collision, the airbag can cause
serious injuries to a child who is
unrestrained, improperly restrained,
sitting too close to the airbag, or out
of position.
A side airbag also poses risks. If any
part of a larger child’s body is in the
path of a deploying side airbag, the
child could receive possibly serious
injuries. The National Highway Traffic Safety
Administration and Transport
Canada recommend that all children
age 12 and under be properly
restrained in a back seat. Physically, a child must be large
enough f or the lap/shoulder belt to
properly f it (see page ). If the seat
belt does not f it properly, with or
without the child sitting on a booster
seat, the child should not sit in f ront.
To saf ely ride in f ront, a child must
be able to f ollow the rules, including
sitting properly, and wearing the seat
belt properly throughout a ride.50
Protecting L arger Children
Physical Size
Maturity
When Can a L arger Child Sit in
Front
52

Î
Î
Î
The U.S. instrument panel is shown. Dif f erences f or the Canadian models are noted in the text.
:
Instrument Panel
Inst rument s and Cont rols
59
CHARGING SYSTEM
INDICATOR
LOW OIL
PRESSURE
INDICATOR VEHICLE STABILITY ASSIST (VSA)
SYSTEM INDICATOR
LIGHTS ON INDICATOR FOG LIGHT
INDICATOR
LOW TIRE PRESSURE
INDICATORANTI-LOCK BRAKE
SYSTEM INDICATOR
VSA
ACTIVATION
INDICATOR
KEYLESS ACCESS
SYSTEM INDICATOR
SIDE AIRBAG OFF
INDICATOR
SECURITY
SYSTEM
INDICATOR
PARKING BRAKE AND
BRAKE SYSTEM
INDICATOR
SEAT BELT REMINDER
INDICATOR
CRUISE MAIN INDICATOR
ADAPTIVE FRONT LIGHTING
(AFS) SYSTEM INDICATOR
(P.66)
(P.60, 348)
(P.64)
(P.60, 348)
(P.60,349)
(P.65,272)
(P.69)(P.64)
(P.65, 277)
(P.62)(P.21,
60)(P.61,
350)
(P.62,
275)(P.67,
107)
(P.
64)
(P.63,
281)
(P.66)
(P.67) (P.63,
281)
(P.64)
(P.62)
(P.33,61)
(P. 66)
MESSAGE INDICATOR
MALFUNCTION INDICATOR
LAMP SH-AWD INDICATOR
MULTI-INFORMATION
DISPLAY HIGH BEAM INDICATOR
LOW FUEL INDICATOR
IMMOBILIZER SYSTEM
INDICATORSUPPLEMENTAL RESTRAINT SYSTEM
INDICATOR
(P.32,
61)
ELECTRONICALLY
CONTROLLED
POWER STEERING
SYSTEM (ECPS)
INDICATOR

This indicator comes on f or a f ew
seconds when you turn the ignition
switch to ON (II).
Itcomesonasareminderthatyou
have turned off the Adaptive Front
Lighting System (AFS).
This indicator blinks when there is a
problem with the AFS system; you
will also see a ‘‘CHECK ADAPTIVE
FRONT LIGHTING SYSTEM’’
message on the multi-inf ormation
display (see page ). If this
happens, stop the vehicle in a saf e
place, turn the ignition switch to
ACCESSORY (I) or LOCK (0), and
restart the engine. If the indicator
does not go of f or blinks again, take
your vehicle to a dealer to have it
checked. For more inf ormation, see
page .This indicator comes on when the
security system is set. For more
inf ormation, see page .
76
107 200
A daptive Front L ighting
(A FS) System Indicator
Security System Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
67
SECURITY SYSTEM INDICATOR

If you turn the ignition switch to
ACCESSORY (I) or LOCK (0), or
move the shift lever out of Park, the
display will change to the normal
screen.
To have the driver’s ID detected,
make sure your remote is linked to
the system (seeon page ). Then use your
remote to unlock the doors (see on page ).
When the ignition switch is in the
ON (II) position, the multi-
inf ormation display shows the driver’s
ID.
You cannot customize the setting; When the keyless memory
settings are of f (see page ).
When you disconnect the vehicle
battery, and then do not unlock
the door.
When the multi-information
display does not show the driver’s
ID. 86
88
167CUST OMIZE MENU 15 SEC
0SEC
MAX
HIGH
MID
LOW
MIN
SHIFT FROM P
WITH VEH SPD
OFF
SHIFT TO P
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 SEC
60 SEC
30 SEC
INTERMITTENT
WITH VEH SPDDEFAULT
15 SEC
MID
WITH VEH
SPD
SHIFT TO
P
DRIVER
DOOR
ON
30 SEC
WITH VEH
SPD
See page
92
See page
93
See page
95
See page
96
See page
97
See page
97
See page
98
See page
100
LIGHTING SETUP
DOOR/WINDOW
SETUP
WIPER SETUP
HEADLIGHT AUT O
OFF TIMER
AUTO LIGHT
SENSITIVITY
EXIT
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
SECURITY RELOCK
TIMER
EXIT
WIPER ACTION
EXIT
EXITCUST OMIZE SET UP
CUST OMIZE GROUP
KEYLESS LOCK
ACKNOWLEDGMENT
Multi-Inf ormation Display
Memory Position
Link
K eyless A ccess Setup
Inst rument s and Cont rols
79

Û
Ý
With the ignition switch in the ON
(II) position, press the INFO button
f or more than 3 seconds, then
release it. The CUSTOMIZE ENTRY
screen appears on the multi-
inf ormation display.
Select CHG SETTING, and press the
SEL/RESET button. Select DOOR/WINDOW SET UP,
and press the SEL/RESET button.
Each time you press the INFO ( /
) button, the display changes as
shown in the illustration.
Here are the settings you can
customize in this mode:
DOOR LOCK MODE AUTO DOOR LOCK
AUTO DOOR UNLOCK
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK TIMER If you select EXIT and press the
SEL/RESET button, the
CUSTOMIZE GROUP screen is
shown again.
Door/Window Setup
Multi-Inf ormation Display
94