2005 Acura MDX ECO mode

This indicator monitors the
temperature of the automatic
transmission f luid. The indicator
should come on f or a f ew seconds
when you turn the ignition switch to
ON (II). If it comes on while driving,
it indicates the transmission f luid
temperature is too high. Pull to the
side of the road when it is saf e, shif t
to Park, and let the engine idle until
the indicator goes out.This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to ON (II). If this
indicator comes on at any other time,
there is a problem in the 4WD
system. Take the vehicle to your
dealer to have it checked.
If the indicator blinks while driving,
pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out.
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. This indicator
will also come on when the light
switch is in AUTO and the lights
turn on automatically.
If you turn the ignition switch to
ACCESSORY (I) or LOCK (0)
without turning of f the light switch,
this indicator will remain on. A
reminder chime will also sound when
you open the driver’s door.
U.S. models only
U.S. Models except Touring
Lights On Indicator A/T Temperature
IndicatorVTM-4 Indicator
Instrument Panel Indicators
64
Continuing to drive with the VTM-4
indicator blinking may cause serious
damage to the system.
Continuing to drive with the A/T
Temperature indicator on may cause
serious damage to the transmission.

µ
µ µ
Press and hold this
button for about 1 second to attract
attention; the horn will sound and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter or turn the ignition
switch to ON (II).
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
Press this button once to
lock all doors and the tailgate. Some
exterior and interior lights will f lash.
When you push LOCK twice within 5
seconds, you will hear a beep to
verify that the doors and tailgate are
locked and the security system has
set. This button does not work if any
door or tailgate is not f ully closed. If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
Press this button once
to unlock the driver’s door. Push it
twice to unlock the other doors.
Some exterior and interior lights will
flash twice when you push the
button. If you do not open any door
orthetailgatewithin30seconds,
they will automatically relock.
When you press the UNLOCK
button, the f ront and rear individual
map lights and the cargo area light,
depending on their switch positions,
will come on (see page ). If you
do not open any door or the tailgate,
the lights stay on for about 30
seconds, then go out. If you relock
thedoorsandthetailgatewiththe
remote transmitter before 30
seconds have elapsed, the lights will
go of f immediately. 96
Remote Transmitter
PA NIC
LOCK UNL OCK
Remote Transmitter Care
Inst rument s and Cont rols
83
LED
UNLOCK
BUTTON
PANIC
BUTTON LOCK
BUTTON

On Touring Model
You can turn the driving position
memory activation off and on. To
turn it of f , press and hold the LOCK
and UNLOCK buttons at the same
time f or about one second. The LED
in the remote transmitter will blink
twice. Then release the buttons.
To turn it back on, repeat this
procedure. The LED will come on
f or one second to indicate the
f eature has been turned on.
Each remote transmitter will also
activate the Driving Position
Memory System (see page ).
When you unlock and open the
driver’s door with the remote
transmitter, you will hear a beep.
The driver’s seat, except power
lumbar, and outside mirrors move to
the positions stored in that memory
location. You will hear two beeps when the movement is complete.
The driving position memory
activated (Memory 1, Memory 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry. If the seat and mirrors are already in
the proper positions, you will hear
three beeps when you open the door.
97
Remote Transmitter
Recalling a Memorized Driving Position
Inst rument s and Cont rols
85
With Memory 1 With Memory 2

Touring Model
Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
Seat, except f or power lumbar, and
outside mirror positions, can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button or
using the appropriate remote
transmitter (Memory 1 or
Memory 2).
Adjust the outside mirrors f or best
visibility (see page ). Adjust the seat to a comfortable
position (see page ).
Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Turn the ignition switch to ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is in the ON (II)
position. You can recall a
memorized position with the
ignition switch in any position.3.
1.
2.
86
96
CONT INUED
Storing a Driving Position in
Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols
97
MEMO BUTTON
MEMORY BUTTONS

Press the RR A/C MANUAL button
to enable the rear A/C control panel.
The indicator in the button will come
on. A passenger in the second row
can then use the temperature control
dial, f an speed dial, and mode
buttons to adjust the temperature
and airflow to their preference. This
is limited by the system’s minimum
and maximum temperature.Individual rear control
settings are shut off when the
ignition is turned off and return to
the automatic settings. They must be
reset when the ignition is turned on
again.
Theclimatecontrolsystemhastwo
sensors. A sunlight sensor is in the
top of the dashboard, and a
temperature sensor is next to the
steering column. Do not cover the
sensors or spill any liquid on them.
Rear Climate Control, Climate Control Sensors
Using the Rear A /C Unit Climate Control Sensors
Features
111
NOTE:
TEMPERATURE SENSOR
TEMPERATURE CONTROL DIAL
MODE BUTTONS
FAN SPEED CONTROL DIAL

µµ
µ µ
µ
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset buttons.
You will see a ‘‘0’’ displayed if auto
select cannot f ind a strong station f or
every preset button.
If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind stations, then
store them in the preset buttons as
described previously. press the
A. SEL button. This restores the
presets you originally set.
Adjust the Balance,
or side-to-side strength of the sound.
Adjust the Fader, or the
f ront-to-back strength of the sound.
AdjusttheTrebleinthe
sound.
Adjust the Bass in the
sound. On models with navigation system,
pushandholdtheTUNEbuttonfor
5 seconds to display inf ormation on
the navigation screen. Press the TUNE knob repeatedly to
display Bass, Treble, Balance, and
Fader settings. Turn the TUNE knob
to adjust the setting. The indicators
on the display will show you the
adjustable range. The system will
return to the audio display in about 5
seconds.To turn of f Auto Select,AUTO SELECT
Adjusting the Sound
BAL ANCE
FADER
TREBLE
BASS
Playing the Radio
Features
115

µÓÓµ
µ
µ´
Satellite radio receives signals f rom
two satellites to produce clear, high-
quality digital reception. It of f ers
many channels in several categories.
Along with a large selection of
dif f erent types of music, satellite
radio also allows you to view channel
and category selections in the audio
display. To switch between the
channel mode and the category
mode,pressandholdtheDISP/
MODE button until the mode
changes. On models with navigation
system, touch the MODE icon on the
audio display.
In the channel mode, you can select
all of the available channels. In the
category mode, such as Jazz, Rock,
Classical, etc., you can select all of
the channels within that category.
Each time you press and release the
DISP/MODE button, the display
changes in the f ollowing sequence:
channel name, channel number,
category, artist name, and music title.
You may experience periods when
XM Radio does not transmit the
artist’s name and song title
inf ormation. If this happens, there is
nothing wrong with your system.
Your vehicle is capable of receiving
XM
Satellite Radio anywhere in the
United States, except Hawaii and
Alaska.
XM
is a registered trademark of
XM Satellite Radio, Inc. On models with navigation system,
pushandholdtheTUNEbuttonfor
5 seconds to display XM inf ormation
on the navigation screen.
In the
category mode, press either button
to select another category. Turn the TUNE knob lef t
or right to select channels. In the
category mode, you can only select
channels within that category.
To listen to satellite radio, turn the
ignition switch to ACCESSORY(I) or
ON (II). Push the PWR/VOL knob
to turn on the audio system, and
press the XM button. Adjust the
volume by turning the PWR/VOL
knob. The last channel you listened
to will show in the display.
Playing t he XMSatellite Radio (U.S. Models)
Operating the Satellite Radio MODE
CAT EGORY ( or ) TUNE
Features
119

µµ
The SCAN f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the stations within that
category are scanned. To activate
SCAN, press the SCAN button or
touch the SCAN icon on the audio
display (models with navigation
system). The system plays each
channel in numerical order f or a f ew
seconds, then selects the next
channel. When you hear a channel
you want to continue listening to,
press the button or touch the icon
again. To store a channel:
To store a channel:
Pick the preset button (icon) you
want f or that channel. Press and
hold the button (icon) until you
hear a beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Once a channel is stored, simply
press and release the proper preset
button (icon) to tune to it.
The presets will be lost if your
vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
Youcanstoreupto12
preset channels using the six preset
buttons or preset icons (on models
with navigation system). Each button
stores one channel f rom the XM1
band and one channel f rom the XM2
band.
Press the XM button. Either XM1
or XM2 will show in the display. Press the XM button again. The
other XM band will show. Store
the next six channels using steps 2
and 3.
Use the TUNE knob, or the
CATEGORY or SCAN buttons to
tune to a desired channel.
In the category mode, only channels
within that category can be selected.
In the channel mode, all channels
can be selected. 3.
4.
5.
1.
2.
Playing t he XMSatellite Radio (U.S. Models)
SCAN Preset
120