2004 YAMAHA YZF-R1S remove seats

5-27
VALVES AND VALVE SPRINGSENG
NOTE:
NOTE:
NOTE:
NOTE:
EAS00237
REMOVING THE VALVES
The following procedure applies to all of the
valves and related components.
Before removing the internal parts of the cylin-
der head (e.g., valves, valve springs, valve
seats), make sure the valves properly seal.
1. Remove:

valve lifter
1

valve pad 2
Make a note of the position of each valve lifter
and valve pad so that they can be reinstalled in
their original place.
2. Check:

valve sealing
Leakage at the valve seat
Check the valve
face, valve seat, and valve seat width.
Refer to “CHECKING THE VALVE SEATS”.
a. Pour a clean solvent
a into the intake and
exhaust ports.
b. Check that the valves properly seal.
There should be no leakage at the valve seat
1.
3. Remove:

valve cotters
1
Remove the valve cotters by compressing the
valve spring with the valve spring compressor
2 and the valve spring compressor attachment
3.
Valve spring compressor
90890-04019, YM-04019
Valve spring compressor
attachment
Intake valve
90890-04114, YM-4114
Exhaust valve
90890-04108, YM-4108
ProCarManuals.com

5-35
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9Removing the stator coil assembly
Rider seat
Fuel tank
Left side cowling
Bottom cowlings
Engine oil
Stator coil assembly lead coupler
Plug
Generator rotor cover
Gasket
Dowel pin
Generator rotor assembly
Dowel pin
Bearing housing
Collar1
1
1
1
2
1
2
1
1Remove the parts in the order listed.
Refer to “SEATS” in chapter 3.
Refer to “FUEL TANK” in chapter 3.
Refer to “COWLINGS” in chapter 3.
Drain.
Refer to “CHANGING THE ENGINE OIL”
in chapter 3.
Disconnect.
10 Nm (1.0 m
kg, 7.2 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
14 Nm (1.4 m
kg, 10 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
STARTER CLUTCH AND GENERATORENG
STARTER CLUTCH AND GENERATOR
STATOR COIL ASSEMBLY
ProCarManuals.com

5-38
STARTER CLUTCH AND GENERATORENG
NOTE: REMOVING THE GENERATOR
1. Remove:

rider seat

fuel tank
Refer to “SEATS” and “FUEL TANK” in chapter
3.
2. Remove:

left side cowling

bottom cowlings
Refer to “COWLINGS” in chapter 3.
3. Drain:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Remove:

plug

generator rotor cover
1

While pushing generator rotor, remove the
generator rotor cover.

Loosen each bolt 1 / 4 of a turn a time, in stages
and in a crisscross pattern.

After all of the bolts are fully loosened, remove
them.
5. Remove:

generator rotor and starter clutch assembly
1.
6. Remove:

idler gear shaft bolt
1

idler shaft

idler gear
2
ProCarManuals.com

5-43
Order Job / Part Q’ty Remarks
1
2
3
4
5
6Removing the crankshaft position
sensor
Rider seat
Fuel tank
Side cowlings
Bottom cowlings
Engine oil
Crankshaft position sensor lead coupler
Crankshaft position sensor
O-ring
Pickup rotor cover
Gasket
Cover1
1
1
1
1
1Remove the parts in the order listed.
Refer to “SEATS” in chapter 3.
Refer to “FUEL TANK” in chapter 3.
Refer to “COWLINGS” in chapter 3.
Drain.
Refer to “CHANGING THE ENGINE OIL”
in chapter 3.
Disconnect.
For installation, reverse the removal
procedure.
10 Nm (1.0 m
kg, 7.2 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
CRANKSHAFT POSITION SENSORENG
CRANKSHAFT POSITION SENSOR
ProCarManuals.com

5-44
CRANKSHAFT POSITION SENSORENG
NOTE:
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
REMOVING THE CRANKSHAFT POSITION
SENSOR
1. Remove:

rider seat

fuel tank
Refer to “SEATS” and “FUEL TANK” in chap-
ter 3.
2. Remove:

right side cowling

bottom cowlings
Refer to “COWLINGS” in chapter 3.
3. Drain:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Disconnect:

crankshaft position sensor lead coupler
5. Remove:

crankshaft position sensor

O-ring

pickup rotor cover
1
Loosen each bolt 1 / 4 of a turn a time, in stages
and in a crisscross pattern.
After all of the bolts are fully loosened, remove
them.
INSTALLING THE CRANKSHAFT POSITION
SENSOR
1. Install:

gasket
New

pickup rotor cover
1

O-ring New

crankshaft position sensor
LOCTITE
2. Connect:

crankshaft position sensor lead coupler
3. Fill:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Install:

right side cowling

bottom cowlings
Refer to “COWLINGS” in chapter 3.
ProCarManuals.com

6-1
Order Job / Part Q’ty Remarks
1
2
3
4
5Removing the radiator
Rider seat
Fuel tank
Air filter case
Side cowlings
Bottom cowling
Coolant
Fuse box stay
Coolant reservoir hose
Radiator
Radiator fan motor
Radiator inlet hose1
1
1
2
1Remove the parts in the order listed.
Refer to “AIR FILTER CASE” in chapter 3.
Drain.
Refer to “CHANGING THE COOLANT” in
chapter 3.
Disconnect.
Refer to “COWLINGS” in chapter 3.
Refer to “SEATS” in chapter 3.
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
5 Nm (0.5 m
kg, 3.6 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
RADIATORCOOL
EAS00454
COOLING SYSTEM
RADIATOR
ProCarManuals.com

6-8
Order Job / Part Q’ty Remarks
1
2
3
4
5Removing the thermostat assembly
Rider seat
Fuel tank
Air filter case
Coolant
Thermostat assembly outlet hose
Thermostat assembly breather hose
Thermostat assembly
Thermostat assembly inlet hose
Band1
1
1
1
2Remove the parts in the order listed.
Refer to “SEATS” in chapter 3.
Refer to “FUEL TANK” in chapter 3.
Refer to “AIR FILTER CASE” in chapter 3.
Drain.
Refer to “CHANGING THE COOLANT” in
chapter3.
For installation, reverse the removal
procedure.
THERMOSTATCOOL
EAS00460
THERMOSTAT
ProCarManuals.com