2004 YAMAHA YZF-R1S ad blue
[x] Cancel search: ad bluePage 359 of 457
7-15
FUEL INJECTION SYSTEMFI
Cylinder identification sensor
output voltage
When sensor is on
4.8 V or more
When sensor is off
0.8 V or less Tester positive probe white / black
Tester negative probe black / blue
1
2
TROUBLESHOOTING DETAILS
This section describes the measures per fault code number displayed on the meter. Carry out check
and maintenance on items or components that could be a cause of malfunction in accordance with the
order.
When the check and maintenance of malfunctioned part is completed, restore the meter display ac-
cording to the “Restore method”.
Fault code No.:
Fault code number displayed on the meter when the engine failed to work normally. (Refer to “Diag-
nostic fault code table”.)
Diagnostic code No.:
Code number to be used when the diagnostic monitoring mode is operated. (Refer to “DIAGNOS-
TIC MODE”.)
Fault code No.11SymptomNo normal signals are received from the cylinder identification sensor.
Used diagnostic code No. – –
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Installed condition of sensorCheck the installed area for looseness or
pinching.Reinstated by
starting the
2Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Cylinder identification sensor coupler
Main wiring harness ECU coupler
Sub-wire harness couplerengine and
operating it at
idle.
3Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short circuit.
Between sensor coupler and ECU coupler
Blue – Blue
White / Black – White / Black
Black / Blue – Black / Blue
4Defective cylinder identification sensor.Replace if defective.
1. Connect the pocket tester (DC 20 V) to the
cylinder identification sensor coupler terminal
as shown.
2. Set the main switch to “ON”.
3. Measure the cylinder identification sensor out-
put voltage.
4. Is the cylinder identification sensor OK?
ProCarManuals.com
Page 360 of 457
7-16
Crankshaft position sensor
resistance
336 504 Ω at 20C (68F)
(between gray and black) Tester positive probe gray
Tester negative probe black
1
2
12
FUEL INJECTION SYSTEMFI
Fault code No.12SymptomNo normal signals are received from the crankshaft position sensor.
Used diagnostic code No. – –
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Installed condition of sensorCheck the installed area for looseness or
pinching.Reinstated by
cranking the
2Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Crankshaft position sensor coupler
Main wiring harness ECU couplerengine.
3Open or short circuit in wiring harness.Repair or replace if there is an open or short
circuit between the main wiring harnesses.
Between sensor coupler and ECU coupler
Gray – Gray
Black / Blue – Black / Blue
4Defective crankshaft position sensor.Replace if defective.
1. Disconnect the crankshaft position sensor cou-
pler from the wire harness.
2. Connect the pocket tester (Ω 100) to the
crankshaft position sensor coupler as shown.
3. Measure the crankshaft position sensor resis-
tance.
4. Is the crankshaft position sensor OK?
ProCarManuals.com
Page 361 of 457
7-17
Intake air pressure sensor output
voltage
3.75 4.25 V Tester positive probe pink / white
Tester negative probe black / blue
1
2
FUEL INJECTION SYSTEMFI
Fault code No.13SymptomIntake air pressure sensor – open or short circuit detected.
Used diagnostic code No. 03 (intake air pressure sensor)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Intake air pressure sensor coupler
Main wiring harness ECU coupler
Sub-wire harness couplerReinstated by
turning the
main switch
ON.
2Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short
circuit.
Between sensor coupler and ECU coupler
Black / Blue – Black / Blue
Pink / White – Pink / White
Blue – Blue
3Defective intake air pressure sensorExecute the diagnostic monitoring mode (Code
No.03).
Replace if defective.
1. Connect the pocket tester (DC 20 V) to the
intake air pressure sensor coupler terminal as
shown.
2. Set the main switch to “ON”.
3. Measure the intake air pressure sensor output
voltage.
4. Is the intake air pressure sensor OK?
ProCarManuals.com
Page 363 of 457
7-19
FUEL INJECTION SYSTEMFI
Fault code No.15SymptomThrottle position sensor – open or shrt circuit detected.
Used diagnostic code No. 01 (throttle position sensor)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Installed condition of throttle position
sensor.Check the installed area for looseness or
pinching.
Check that it is installed in the specified
position.
Refer to “THROTTLE BODIES” section.Reinstated by
turning the
main switch
ON.
2Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Throttle position sensor coupler
Main wiring harness ECU coupler
Sub-wire harness coupler
3Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short
circuit.
Between sensor coupler and ECU coupler
Black / Blue – Black / Blue
Yellow – Yellow
Blue – Blue
4Throttle position sensor lead wire open
circuit output voltage check.Check for open circuit and replace the throttle
position sensor.
Black / Blue – Yellow
Open circuit item Output voltage
Ground wire open 5 V
circuit
Output wire open 0V
circuit
Power supply wire 0V
open circuit
5Defective throttle position sensor.Execute the diagnostic mode (Code No.01).
Replace if defective.
Refer to “THROTTLE BODIES” section.
Fault code No.16SymptomStuck throttle position sensor detected.
Used diagnostic code No.01 (throttle position sensor)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1When detecting fault code No.15.Refer to “Fault code No.15”.Reinstated by
2Installed condition of throttle position
sensor.Check the installed area for looseness or pinching.
Check that it is installed in the specified position.
Refer to “THROTTLE BODIES” section.starting the
engine,
operating it at
idle and then3Defective throttle position sensorExecute the diagnostic mode (Code No.01).
Replace if defective.
Refer to “THROTTLE BODIES” section.idle, and then
racing it.
ProCarManuals.com
Page 364 of 457
7-20
FUEL INJECTION SYSTEMFI
EXUP servomotor resistance
(when the pulley is turned once)
5.25 9.75 kΩ at 20C (68F) Positive tester terminal blue
Negative tester probe white / red
1
2
Fault code No.17SymptomEXUP servo motor potention circuit – open or short circuit detected.
Used diagnostic code 53
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
EXUP servo motor coupler
Main wireharness ECU couplerReinstated by
turning the
main switch
ON.
2Open or short circuit in wire harness.Repair or replace if there is an open or short
circuit.
Between motor coupler and ECU coupler
Blue – Blue
White / Red – White / Red
Black / Blue – Black / Blue
3Defective EXUP servo motor potention
circuit.Execute the diagnostic mode (Code No.53).
Replace if defective.
1. Disconnect the EXUP servomotor coupler from
the wire harness.
2. Connect the pocket tester (Ω 1k) to the
EXUP servomotor coupler.
3. While slowly turning the EXUP servomotor
pulley, measure the EXUP servomotor resis-
tance.
4. Is the EXUP servomotor OK?
ProCarManuals.com
Page 366 of 457
7-22
FUEL INJECTION SYSTEMFI
Fault code No.19SymptomOpen circuit in the input line of ECU No.15 terminal is detected.
Used diagnostic code No. 20 (sidestand switch)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Connected condition of connector
Main wiring harness ECU coupler
(No.15 pin)
Check the coupler for any pins that may have
pulled out.
Check the locking condition of the coupler.
If there is a malfunction, repair it and connected it
securely.If the
transmission is
in gear, it is
reinstated by
retracting the
sidestand.
If the
2Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short
circuit.
Between sidestand switch coupler and ECU
coupler
Blue / Black – Blacktransmission is
in neutral, it is
reinstated by
reconnecting
the wiring.
3The malfunction of the sidestand switch.Replace if defective.
Refer to “CHECKING THE SWITCHES” in
chapter 8.
Fault code No.20SymptomDefective values are detected due to the internal malfunction of the intake air
pressure sensor or the atmospheric pressure sensor.
Used diagnostic code No. 02 (atmospheric pressure sensor) 1
03 (intake air pressure sensor) 2
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Defective atmospheric pressure sensorExecute the diagnostic mode (Code No.02).
Replace if defective.
Refer to “Fault code No.23”.Reinstated by
turning the
main switch
2Defective intake air pressure sensorExecute the diagnostic mode (Code No.03).
Replace if defective.
Refer to “Fault code No.13”.ON.
ProCarManuals.com
Page 367 of 457
7-23
FUEL INJECTION SYSTEMFI
Fault code No.21SymptomOpen or short circuit is detected from the coolant temperature sensor.
Used diagnostic code No. 06 (coolant temperature sensor)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Coolant temperature sensor coupler
Main wiring harness ECU coupler
Sub-wire harness couplerReinstated by
turning the
main switch
ON.
2Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short
circuit.
Between sensor coupler and ECU coupler
Black / Blue – Black / Blue
Green / White – Green / White
3Defective coolant temperature sensor.Execute the diagnostic mode (Code No.06).
Replace if defective.
Refer to “COOLING SYSTEM” in chapter 8.
ProCarManuals.com
Page 368 of 457
7-24
FUEL INJECTION SYSTEMFI
Intake air temperature sensor
resistance
2.21 2.69 kΩ at 20C (68F) Tester positive probe brown / white
Tester negative probe black / blue
1
2
12
Handle the intake air temperature sensor
with special care.
Never subject the intake air temperature sen-
sor to strong shocks. If the intake air temper-
ature sensor is dropped, replace it.
WARNING
Fault code No.22SymptomOpen or short circuit detected from the intake temperature sensor.
Used diagnostic code No. 05 (intake temperature sensor)
OrderInspection operation item and probable
causeOperation item and countermeasureReinstatement
method
1Connected condition of connector
Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.If there is a malfunction, repair it and connect it
securely.
Intake temperature sensor coupler
Main wiring harness ECU coupler
Sub-wire harness couplerReinstated by
turning the
main switch
ON.
2Open or short circuit in wiring harness
and / or sub lead.Repair or replace if there is an open or short
circuit.
Between sensor coupler and ECU coupler
Black / Blue – Black / Blue
Brown / White – Brown / White
3Defective intake temperature sensor.Execute the diagnostic mode (Code No.05).
Replace if defective.
1. Remove the intake air temperature sensor
from the air filter case.
2. Connect the pocket tester (Ω 100) to the
intake air temperature sensor terminal as
shown.
3. Measure the intake air temperature sensor
resistance.
4. Is the intake air temperature sensor OK?
ProCarManuals.com