2004 YAMAHA YZ250LC ignition

CHAPTER 6
ELECTRICAL
ELECTRICAL COMPONENTS AND
WIRING DIAGRAM.....................................6-1
IGNITION SYSTEM.....................................6-2
SOLENOID VALVE SYSTEM.....................6-7
TPS (THROTTLE POSITION SENSOR)
SYSTEM......................................................6-9
CHAPTER 7
TUNING
ENGINE.......................................................7-1
CHASSIS...................................................7-13
5XF-9-30-0 4/4/03 5:41 PM Page 22

1-7
SPECIAL TOOLS
GEN
INFO
EC140002
SPECIAL TOOLS
The proper special tools are necessary for complete and accurate tune-up and assembly. Using the
correct special tool will help prevent damage caused by the use of improper tools or improvised tech-
niques. The shape and part number used for the special tool differ by country, so two types are provid-
ed. Refer to the list provided to avoid errors when placing an order.
NOTE:
9For U.S.A. and Canada, use part number starting with “YM-”, “YU-” or “ACC -”.
9For others, use part number starting with “90890-”.
Part number Tool name / How to use IIIustration
YU-1135-A, 90890-01135Crankcase separating toolYU-1135-A 90890-01135
This tool is used to split the crankcase as well
as remove the crankshaft from either case.
YM-1189, 90890-01189 Flywheel puller
YM-1189 90890-01189
This tool is used to remove the flywheel magneto.
YU-1235, 90890-01235 Rotor holding tool
YU-1235 90890-01235
This tool is used when loosening or tightening the
flywheel magneto securing nut.
YU-3097, 90890-01252 Dial gauge and stand
YU-3097 90890-01252
YU-1256 Spark plug hole dial standYU-1256
These tools are used to set the ignition timing.
Crankcase installing tool
YU-90050 90890-01274
YU-90050, 90890-01274 PotYU-90063 90890-01275
YU-90050, 90890-01275 Bolt90890-01278
YU-90063, 90890-01278 Adapter
These tools are used to install the crankshaft.
YU-1304, 90890-01304 Piston pin puller
YU-1304 90890-01304
This tool is used to remove the piston pin.
YU-24460-01,90890-01325Radiator cap testerYU-24460-01 90890-01325
YU-33984, 90890-01352 AdapterYU-33984 90890-01352
These tools are used for checking the cooling
system.
5XF-9-30-1 4/22/03 8:54 AM Page 14

1-8
SPECIAL TOOLS
GEN
INFO
Part number Tool name / How to use IIIustration
YU-33975, 90890-01403 Ring nut wrenchYU-33975 90890-01403
This tool is used when tighten the steering ring nut
to specification.
YM-01442, 90890-01442 Fork seal driver
YM-01442 90890-01442
This tool is used when install the fork oil seal.
YM-01494, 90890-01494 Damper rod holder
YM-01494 90890-01494
Use this tool to remove and install the damper rod.
YU-3112-C, 90890-03112 Yamaha pocket tester
YM-3112-C 90890-03112
Use this tool to inspect the coil resistance,
output voltage and amperage.
YU-8036-B Inductive tachometer
YU-8036-B 90890-03113
90890-03113 Engine tachometer
This tool is needed for observing engine rpm.
YM-91042, 90890-04086 Clutch holding tool
YM-91042 90890-04086
This tool is used to hold the clutch when removing
or installing the clutch boss securing nut.
YM-34487 Dynamic spark tester
YM-34487 90890-06754
90890-06754 Ignition checker
This instrument is necessary for checking the igni-
tion system components.
ACC-QUICK-GS-KT Quick gasket
®ACC-QUICK-GS-KT 90890-85505
90890-85505 YAMAHA Bond No. 1215
This sealant (Bond) is used for crankcase mating
surface, etc.
5XF-9-30-1 4/22/03 8:54 AM Page 15

2-2
GENERAL SPECIFICATIONSSPEC
Carburetor:
Type/Manufacturer PWK38S/KEIHIN
Spark plug:
Type/Manufacturer BR8EG/NGK (resistance type)
Gap 0.5~0.6 mm (0.020~0.024 in)
Clutch type: Wet, multiple-disc
Transmission: USA, ZA, AUS, NZ EUROPE, CDN
Primary reduction system Gear←
Primary reduction ratio 63/21 (3.000)←
Secondary reduction system Chain drive←
Secondary reduction ratio 50/14 (3.571) 49/14 (3.500)
Transmission type Constant mesh,←
5-speed
Operation Left foot operation←
Gear ratio: 1st 27/14 (1.929)←
2nd 23/15 (1.533)←
3rd 23/18 (1.278)←
4th 24/22 (1.091)←
5th 20/21 (0.952)←
Chassis:USA, ZA, AUS, NZEUROPE, CDN
Frame type Semi double cradle←
Caster angle 27.0° 26.8°
Trail 118 mm (4.65 in) 114 mm (4.49 in)
Tire:
Type With tube
Size (front) 80/100-21 51M
Size (rear) 110/90-19 62M
Tire pressure (front and rear) 100 kPa (1.0 kgf/cm2, 15 psi)
Brake:
Front brake type Single disc brake
Operation Right hand operation
Rear brake type Single disc brake
Operation Right foot operation
Suspension:
Front suspension Telescopic fork
Rear suspension Swingarm (link type monocross suspension)
Shock absorber:
Front shock absorber Coil spring/oil damper
Rear shock absorber Coil spring/Gas, oil damper
Wheel travel:
Front wheel travel 300 mm (11.8 in)
Rear wheel travel 315 mm (12.4 in)
Electrical:
Ignition system CDI magneto
2
5XF-9-30-2 5/15/03 3:54 PM Page 3

2-11
MAINTENANCE SPECIFICATIONSSPEC
EC212300
ELECTRICAL
Part to be tightened Thread size Q’tyT ightening torqueNm m•kg ft•lb
Stator M 6 ×1.0 3 8 0.8 5.8
Rotor M12 ×1.25 1 56 5.6 40
Ignition coil M 6 ×1.0 2 7 0.7 5.1
Item Standard Limit
Ignition system:
Ignition timing (B.T.D.C.) 0.18 mm (0.007 in)…
Advancer type Electrical…
CDI:
Magneto-model (stator)/Manufacturer 5CU-02/YAMAHA…
Source coil 1 resistance (color) 720~1,080 Ωat 20°C (68°F)…
(Black-Black/Red)
Source coil 2 resistance (color) 44~66 Ωat 20°C (68°F)…
(Green/Blue-Green/White)
Pickup coil resistance (color) 248~372 Ωat 20°C (68°F)…
(White/Blue-White/Red)
CDI unit-model/Manufacturer 5NX-01/YAMAHA…
Ignition coil:
Model/Manufacturer 4MX-00/YAMAHA…
Minimum spark gap 6 mm (0.24 in)…
Primary winding resistance 0.20~0.30 Ωat 20°C (68°F)…
Secondary winding resistance 9.5~14.3 kΩat 20°C (68°F)…
Spark plug cap:
Resistance 4~6 kΩat 20°C (68°F)…
5XF-9-30-2 5/15/03 3:54 PM Page 12

2-14
CABLE ROUTING DIAGRAMSPEC
1Ground lead
2Ignition coil lead
3Clamp
4Wireharness
5CDI magneto lead
6YPVS breather hose
7Radiator breather hose
8Cable guide
9“ENGINE STOP” button lead
0Brake hose
APass the “ENGINE STOP” but-
ton lead on the inside of the
ignition coil lead and ground
lead.BClamp the “ENGINE STOP” but-
ton lead, ground lead, ignition
coil lead, wireharness and CDI
magneto lead with the clamp
ends downward.
In so doing, clamp the “ENGINE
STOP” button lead at its con-
nector and do not allow the CDI
magneto lead to slacken.
Also make sure that the ignition
coil lead is not pulled.
CPass the radiator breather hose
outside the engine bracket and
inside the down-tube.Pass the
radiator breather hose inside
the CDI magneto lead.
DClamp the CDI magneto lead,
radiator breather hose and
YPVS breather hose. In so
doing, clamp the CDI magneto
lead at the rear of the down-tube
with the clamp ends outward.EClamp the radiator breather
hose and CDI magneto lead at
the rear of the down-tube with
the clamp ends outward.
FPass the radiator breather hose
and CDI magneto lead in front
of the radiator hose.
GPass the radiator breather hose
between the frame and radiator.
HAlign the top of the brake hose
neck with the brake hose holder
bottom.
IPass the brake hose in front of
the axle boss,then fit it into the
hose groove so that the brake
hose does not contact the nut
(wheel axle).
JFit the brake hose into the guide
on the protector.
5XF-9-30-2 5/15/03 3:54 PM Page 52

2-15
CABLE ROUTING DIAGRAMSPEC
1Radiator breather hose
2Ground lead
3Clamp
4Wireharness
5High tension cord
6Ignition coil
7Throttle cable
8“ENGINE STOP” button lead
9Clutch cable
0Engine bracketAClamp the clutch cable, high
tension cord and wireharness at
the protector of the high tension
cord so that the clamp passes
with its ends downward, as
shown.
BPosition the CDI magneto lead
coupler between the radiators.
CInstall the radiator hose with the
paint facing the right of the frame
so that the hose does not come
in contact with the CDI unit.
DClamp the wireharness to the
right engine bracket.
EClamp the high tension cord,
throttle cable and wireharness
with the clamp ends downward,
so that the high tension cord
does not contact the engine
bracket installation bolts.FFasten the ground lead together
with the front installation portion
of the ignition coil.
GPass the radiator breather hose
at the rear of the radiator hose
and in front of the ignition coil
bracket.
H
Position each lead at the lower
left of the main tube (frame)
and put the clamp ends within
the area as shown by the
arrow.
5XF-9-30-2 5/15/03 3:54 PM Page 54

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~24
results of test runs before racing? Are inspection and
maintenance completely done?
5XF-9-30-3A 4/21/03 2:09 PM Page 14