2004 YAMAHA WHY 50 oil pressure

PRE-OPERATION CHECKS
4
•Check fuel level in fuel tank.
Fuel•Refuel if necessary. 3-5 — 3-6
•Check fuel line for leakage.
•Check oil level in oil tank.
2-stroke engine oil•If necessary, add recommended oil to specified level. 3-5 — 3-7
•Check vehicle for oil leakage.
Final transmission oil•Check vehicle for oil leakage. 6-6
•Check operation.
•If soft or spongy, have Yamaha dealer bleed hydraulic system.
Front brake•Check fluid level in reservoir. 3-5, 6-13 — 6-15
•If necessary, add recommended brake fluid to specified level.
•Check hydraulic system for leakage.
•Check operation.
Rear brake•Check pedal free play. 3-5, 6-13 — 6-15
•Adjust if necessary.
•Make sure that operation is smooth.
Throttle grip•Check cable free play.
6-9, 6-15
•If necessary, have Yamaha dealer adjust cable free play
and lubricate cable and grip housing.
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or
loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual
inspection, to check the following points before each ride.
EAU03439
Pre-operation check list
ITEM CHECKS PAGE
4-1

PERIODIC MAINTENANCE AND MINOR REPAIR
6
•Check tread depth and for damage.
9 * Tires•Replace if necessary.
√√√√ √
•Check air pressure.
•Correct if necessary.
10 * Wheel bearings•Check bearing for looseness or damage.√√√√
11 * Steering bearings•Check bearing play and steering for roughness.√√√√√•Lubricate with lithium-soap-based grease. Every 24,000 km
12 * Chassis fasteners•Make sure that all nuts, bolts and screws are
√√√√ √
properly tightened.
13 Centerstand•Check operation.
√√√√ √
•Lubricate.
14 * Front fork•Check operation and for oil leakage.√√√√
15 * Shock absorber assembly•Check operation and shock absorber for oil leakage.√√√√
16 * Carburetor•Adjust engine idling speed.√√√√√ √
17 * Autolube pump•Check operation.
√√√√
•Bleed if necessary.
18 Final transmission oil•Check vehicle for oil leakage.√√ √•Change.√√√
19 * V-belt•Replace. Every 10,000 km
20 * Front and rear brake
•Check operation.√√√√√ √
switches
ODOMETER READING (x 1,000 km)
NO. ITEMCHECK OR MAINTENANCE JOB
1
ANNUAL
CHECK
6121824
6-3

SCOOTER CARE AND STORAGE
7
Care
While the open design of a scooter
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality
components are used. A rusty exhaust
pipe may go unnoticed on a car,
however, it detracts from the overall
appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly
installed.3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA00011
•Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
•Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
•Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
•Do not use high-pressure
washers or steam-jet cleaners
since they cause water seepage
and deterioration in the following
areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
7-1

SCOOTER CARE AND STORAGE
7 a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
EWA00003
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
5. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to
prevent the tires from becoming
degraded in one spot.
7. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an
excessively cold or warm place
(less than 0 °C or more than 30
°C). For more information on
storing the battery, see page 6-
18.
NOTE :
Make any necessary repairs before
storing the scooter.
7-4

SPECIFICATIONS
8
Chassis:
Frame type Steel tube underbone
Caster angle ((degree)) 25°
Trail 101.3 mm
Tires:
Front:
Type Tubeless
Size 2 1/2-16 42M
Manufacturer / Model MICHELIN / M29S TT
Rear:
Type Tubeless
Size 2 3/4-16 46M
Manufacturer / Model MICHELIN / M29S TT
Maximum load * 182 Kg
Air pressure (cold tire):
Up to 90 Kg load*
Front180 kpa
Rear 190 kpa
90 kg load — maximum
load *
Front180 kpa
Rear 210 kpa
* Total weight of rider, passenger, cargo and accessories.Wheels:
Front
Type Cast wheel
Size 16 X MT 1.60
Rear
Type Cast wheel
Size 16 X MT 1.85
Brakes:
Front
Type Single disc brake
Operation Right hand operation
Type brake fluid DOT 4
Rear
Type Single drum brake
Operation Left hand operation
Suspension:
Front suspension Telescopic fork
Rear suspension Unit swing
Shock absorber:
Front fork type Coil spring/oil damper
Rear shock absorber Coil spring/oil damper
assembly type
Wheel travel:
Front wheel travel 80 mm
Rear wheel travel 70 mm
8-2