2004 YAMAHA VERSITY 300 ESP

INSTRUMENT AND CONTROL FUNCTIONS
3
EAU04121
Turn signal indicator lights ""
and "
"
The corresponding indicator light
flashes when the turn signal switch is
pushed to the left or right.
EAU00063
High beam indicator light ""
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU04031
Speedometer
The speedometer shows the riding
speed.
EAUM0090
Low beam indicator light ""
This indicator light comes on when the
low beam of the headlight is switched
on.
1. Low beam indicator light ""
2. Left turn signal indicator "
"
3. Right turn signal indicator "
"
4. High beam indicator light "
"
km/hkm/hO1O1O2O2O
4O4O6O6O10O10O12O12O
14O14O
16O16O
8O8O
km/hkm/hO1O1O2O2O
4O4O6O6O10O10O12O12O
14O14O
16O16O
8O8O
O 2O
2O4O4O6O6O
10O10O8O8Omphmph
11
ZAUM0402
1. Speedometer
EAU00056
Indicator lights
3-2
UK ONLY
km/hkm/h
O1O1O2O2O
4O4O6O6O10O10O12O12O
14O14O
16O16O
8O8O
F1/2E
H
C15V15V9V9V
12 34
ZAUM0578

INSTRUMENT AND CONTROL FUNCTIONS
3
1
ZAUM0416
EAU00330
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
scooter upright.
NOTE :
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation
of the ignition circuit cut-off system.)
EW000044
The scooter must not be ridden with
the sidestand down, or if the
sidestand cannot be properly moved
up (or does not stay up), otherwise
the sidestand could contact the
ground and distract the operator,
resulting in a possible loss of
control. Yamaha’s ignition circuit cut-
off system has been designed to
assist the operator in fulfilling the
responsibility of raising the
sidestand before starting off.
Therefore, check this system
regularly as described below and
have a Yamaha dealer repair it if it
does not function properly.
1. Sidestand switch
WARNINGEAU00337
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch and
brake light switches) has the following
functions.
•It prevents starting when the
sidestand is up, but neither brake
is applied.
•It prevents starting when either
brake is applied, but the sidestand
is still down.
•It cuts the running engine when
the sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
EW000045
If a malfunction is noted, have a
Yamaha dealer check the system
before riding.
WARNING
3-16

PRE-OPERATION CHECKS
4The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or
loss of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual
inspection, to check the following points before each ride.
EAU03439
Pre-operation check list
ITEM CHECKS PAGE
•Check fuel level in fuel tank.
Fuel•Refuel if necessary. 3-3 — 3-4, 3-10 — 3-11
•Check fuel line for leakage.
•Check oil level in engine.
Engine oil•If necessary, add recommended oil to specified level. 6-13 — 6-15
•Check vehicle for oil leakage.
Final transmission oil•Check vehicle for oil leakage. 6-16
•Check coolant level in reservoir.
Coolant•If necessary, add recommended coolant to specified level. 6-17
•Check cooling system for leakage.
•Check operation.
•If soft or spongy, have Yamaha dealer bleed hydraulic system.
Front brake•Check fluid level in reservoir. 3-9, 6-23 — 6-25
•If necessary, add recommended brake fluid to specified level.
•Check hydraulic system for leakage.
•Check operation.
•If soft or spongy, have Yamaha dealer bleed hydraulic system.
Rear brake•Check fluid level in reservoir. 3-9, 6-23 — 6-25
•If necessary, add recommended brake fluid to specified level.
•Check hydraulic system for leakage.
4-1

OPERATION AND IMPORTANT RIDING POINTS
5
a b
ZAUM0419
EAU00434
Acceleration and
deceleration
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
a . To reduce the speed, turn the
throttle grip in direction b .
PUSHZAUM0472
EAU00435
Braking
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually
increasing the pressure.
EW000057
•Avoid braking hard or suddenly
(especially when leaning over
to one side), otherwise the
scooter may skid or overturn.
•Railroad crossings, streetcar
rails, iron plates on road cons-
truction sites, and manhole
covers become extremely
slippery when wet. Therefore,
slow down when approaching
such areas and cross them with
caution.
•Keep in mind that braking on a
wet road is much more difficult.
•Ride slowly down a hill, as
braking downhill can be very
difficult.
WARNING
5-3

SCOOTER CARE AND STORAGE
7
Care
While the open design of a scooter
reveals the attractiveness of the
technology, it also makes it more
vulnerable. Rust and corrosion can
develop even if high-quality
components are used. A rusty exhaust
pipe may go unnoticed on a car,
however, it detracts from the overall
appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug cap, are tightly
installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such
products onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.CleaningECA00011
•Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the
affected area any longer than
instructed. Also, thoroughly
rinse the area off with water,
immediately dry it, and then
apply a corrosion protection
spray.
•Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
CAUTION:
7-1