2004 YAMAHA TZR50 warning light

EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10640
ON
All electrical circuits are supplied with
power, and the engine can be started.
The key cannot be removed.
NOTE:
The headlight, meter lighting and tai-
llight come on automatically when the
engine is started.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10670
“f”
The 2-stroke engine oil level warning
light should come on. (See page 3-2.)
EAUM1020
“f”
The coolant temperature warning light
should come on when the key is tur-
ned to “
f”. (See page 3-2.)
EAU10680
LOCK
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.T
o unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
EWA10060
s s
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the vehi-
cle is stopped before turning the
key to “OFF” or “LOCK”.
EAU10980
Indicator lights
1. Turn signal indicator light “b”
2. Neutral indicator light “N”
3. Oil level warning light “z”
4. Coolant temperature warning light “y”
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
2 3
41
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 17

EAU11020
Turn signal indicator light “b”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
EAU11060
Neutral indicator light “N”
This indicator light comes on when
the transmission is in the neutral posi-
tion.
EAU11120
Oil level warning light “z”
This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
NOTE:
Even if the oil level is sufficient, the
warning light may flicker when riding
on a slope or during sudden accelera-
tion or deceleration, but this is not a
malfunction.
EAU11440
Coolant temperature warning light
“y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
ECA10020
CAUTION
Do not operate the engine if it is
overheated.
EAU11620
Speedometer unit
1. Speedometer/Odometer
The speedometer unit is equipped
with a speedometer and an odometer.
The speedometer shows riding spe-
ed. The odometer shows the total dis-
tance traveled.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 18

EAU16000
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-9.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “ON” and make
sure that the engine stop switch
is set to “f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-7.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
ECA11160
CAUTION
If the oil level warning light flickers
or remains on after starting, imme-
diately stop the engine, and then
check the engine oil level and the
vehicle for oil leakage. If necessary,
add engine oil, and then check thewarning light again. If the warning
light does not go off after starting
with sufficient engine oil, have a
Yamaha dealer check the electrical
circuit.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION
For maximum engine life, never
accelerate hard when the engine is
cold!
7. When the engine is warm, turn
the starter (choke) off.
NOTE:
The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off.
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 30

EAU20170
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
1. Panel
2. Remove panel (1). (See page 6-8.)
3. Check the coolant level in the
coolant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
4. If the coolant is at or below the
minimum level mark, open the
reservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
ECA10470
CAUTION
If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.
If water has been used instead
of coolant, replace it with coo-
lant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the coo-
ling system will not be protec-
ted against frost and corrosion.
If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
5. Install the panel.
Coolant reservoir capacity:
0,45 L (0.39 Imp.qt)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
MIN MAX
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 40

adjusting nut in direction (b).
6. Tighten the locknut at the clutch
lever and the crankcase.
EAU22220
Adjusting the brake pedal
position and free play
1. Position adjusting bolt
2. Brake pedal position
EWA10670
s s
WARNING
It is advisable to have a Yamaha
dealer make these adjustments.
Brake pedal position
The top of the brake pedal should be
aligned with the top of the footrest as
shown. Periodically check the brake
pedal position and, if necessary,
adjust it as follows.1. Loosen the locknut at the brake
pedal.
2. To raise the brake pedal, turn the
adjusting bolt in direction (a). To
lower the brake pedal, turn the
adjusting bolt in direction (b).
3. Tighten the locknut.
EWA11230
s s
WARNING
After adjusting the brake pedal
position, the brake pedal free play
must be adjusted.
Brake pedal free play
1. Free play
The brake pedal free play should
measure 10~15 mm (0,39~59 in) at
the brake pedal end. Periodically
check the brake pedal free play and, if
necessary, adjust it as follows.To increase the brake pedal free play,
turn the adjusting nut at the brake rod
in direction (a). To decrease the brake
pedal free play, turn the adjusting nut
in direction (b).
EWA10660
s s
WARNING
After adjusting the brake pedal free
play, check the operation of the
brake light.
EAU22270
Adjusting the rear brake light
switch
1. Switch
2. Lock nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
21
1
1
2a
b
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 45

2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
ECA10640
CAUTION
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer check
the electrical system.
EAU23800
Replacing the headlight bulb
This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1. Remove the headlight bulb cover,
and then disconnect the head-
light lead connectors.
2. Unhook the headlight bulb hol-der, and then remove the defecti-
ve bulb.
EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
3. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10660
CAUTION
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the
bulb, and the bulb life will be adver-
sely affected. Thoroughly clean off
any dirt and fingerprints on the
headlight bulb using a cloth mois-
tened with alcohol or thinner.
4. Connect the headlight lead con-
nectors, and then install the bulb
cover.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24281
Replacing a turn signal light
bulb or the tail/brake light
bulb
1. Remove the lens by removing the
screws.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
Specified fuse:
10 A
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 53

Size
130/70-17 62H
Manufacturer/model
PIRELLI
Maximum load
195 kg
Tire air pressure (measured on cold
tires)
Loading condition
0-90 kg
Front
180 kPa
Rear
200 kPa
Loading condition
90-180 kg
Front
190 kPa
Rear
230 kPa
Front wheelWheel type
Cast wheel
Rim size
MT 2.75x17”
Rear wheelWheel type
Cast wheel
Rim size
MT 3.50x17”
Front brakeType
Single disc brakeRecommended fluid
DOT 4
Rear brakeType
Single disc brake
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
130.0 mm
Rear suspension
Type
Swingarm
Spring/shock absorber type
Coil-gas spring/oil damper
Wheel travel
102.0 mm
Electrical systemIgnition system
DC. CDI
Charging system
CDI magneto
Model
YT4L-BS
Voltage, capacity
12 V, 3.0 Ah
Bulb type
Incandescence
Bulb voltage, wattage x quantityHeadlight
12 V, 25 W/25.0 W x 2
Tail/brake light
12 V, 5.0 W/21.0 W x 1
Front turn signal light
12 V, 16.0 W
Rear turn signal light
12 V, 10.0 W x 2
Neutral indicator light
LED
Oil level warning light
LED
Turn signal indicator light
LED
Coolant temperature warning light
LED
Main fuse
10.0 A
8
SPECIFICATIONS
8-2
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 63