2004 YAMAHA GRIZZLY 125 brake

1. Grease nipple (×6)1. Graisseur (×6)1. Boquilla de engrase (×6)
8-73
EBU00725
Brake lever lubrication
Lubricate the pivoting parts of the brake levers.
EBU00728
Knuckle shaft, lower arms and steering shaft
lubrication
Lubricate the pivot points using a grease gun.11
1
1
Recommended lubricant:
Lithium-soap-based grease
(all-purpose grease)
Recommended lubricant:
Lithium-soap-based grease
1C5-9-60-08 9/12/03 8:38 PM Page 8-74

1. Bulb holder1. Fixation d’ampoule1. Portabombillas
1. Bulb 2.Bulb holder
1. ampoule 2.Fixation d’ampoule1. Bombilla 2.Portabombillas
8-91
EBU00861
Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by push-
ing it inward and turning it clockwise.
4. Install the bulb holder (together with the bulb).
1
qw
1C5-9-60-08 9/12/03 8:38 PM Page 8-92

9-3
cC
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high pressure deter-
gent applications such as those available in
coin-operated car washers.
4. Once the majority of the dirt has been hosed
off, wash all surfaces with warm water and
mild, detergent-type soap. An old toothbrush
or bottle brush is handy for hard-to-get-at
places.
5. Rinse the machine off immediately with
clean water and dry all surfaces with a
chamois, clean towel or soft absorbent
cloth.
6. Dry the chain and lubricate it to prevent rust.
1C5-9-60-09~11 15/12/03 7:59 PM Page 4

9-5
7. Clean the seat with a vinyl upholstery clean-
er to keep the cover pliable and glossy.
8. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or pro-
tective finish.
When finished, start the engine and let it idle
for several minutes.
w
Wet brakes may have reduced stopping abili-
ty, increasing the chance of an accident.
Test the brakes after washing. Apply the
brakes several times at slow speeds to let
friction dry out the linings.
1C5-9-60-09~11 15/12/03 7:59 PM Page 6

10-4
Model YFM125
Chassis:
Frame type Steel tube frame
Caster angle 6°
Trail 15 mm
Tire:
Type Tubeless
Size: Front AT20 ×7 - 8
Rear AT22 ×10 - 8
Manufacturer/type:
Front DUNLOP/KT536A
Rear DUNLOP/KT537A
Brake:
Front brake type Drum brake
Operation Right hand operation
Rear brake type Drum brake
Operation Left hand operation
Suspension:
Front Swing axle
Rear Swingarm
1C5-9-60-09~11 15/12/03 7:59 PM Page 15

10-5
Model YFM125
Shock absorber:
Front Coil spring/Oil damper
Rear Coil spring/Oil damper
Wheel travel:
Front 70 mm
Rear 80 mm
Electrical:
Ignition system DC. C.D.I.
Charging system A.C. Magneto
Battery type/voltage, capacity 12N12C-4A-2/12V, 12Ah
Headlight type: Bulb
Bulb volgate, wattage ×quantity:
Headlight 12V, 30 W/30 W ×2
Tail/brake light 12V, 5 W/21 W ×1
Indicator light:
Neutral 12V, 1.7 W ×1
Reverse 12V, 1.7 W ×1
Fuse: 15A
1C5-9-60-09~11 15/12/03 7:59 PM Page 16