2004 YAMAHA BLASTER 200 engine oil

8-35
6. Inspect the sponge material. If damaged,
replace it.
7. Apply SAE 10W30 engine oil to the sponge
material.
NOTE:
The sponge material should be wet but not drip-
ping.
8. Install the sponge material onto its frame
and install the screw.
9. Install the air filter element.
10. Install the air filter case cover by installing
the screws.
11. Install the seat.
5VM-9-61-05 3/14/03 10:48 PM Page 36

8-79
3. Thoroughly lubricate the drive chain with a
special O-ring chain lubricant.
cC
Do not use engine oil or any other lubricants
for the drive chain, as they may contain sub-
stances that could damage the O-rings.
5VM-9-61-05 3/14/03 10:48 PM Page 80

8-81
EBU00570
Cable inspection and lubrication
w
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer
covering of control cables becomes dam-
aged. Cables can also become frayed or
kinked. Operation of controls could be
restricted, which could cause an accident or
injury.
Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a
Yamaha dealer to replace them.
Recommended lubricant:
Engine oil
5VM-9-61-05 3/14/03 10:48 PM Page 82

9-7
EBU00528
B. STORAGE
Long term storage (60 days or more) of your
machine will require some preventive proce-
dures to guard against deterioration. After thor-
oughly cleaning the machine, prepare for stor-
age as follows:
1. Fill the fuel tank with fresh fuel and add fuel
stabilizer (if available).
NOTE:
Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha dealer
if the fuel system is to be drained instead.
2. Remove the spark plug, pour about one
tablespoon of SAE 10W30 or 20W40 motor
oil in the spark plug hole and reinstall the
spark plug. Ground the spark plug wire and
turn the engine over several times to coat
the cylinder wall with oil.
3. Clean the drive chain thoroughly and lubri-
cate it. (See page 8-77.)
5VM-9-61-06 3/14/03 9:40 PM Page 8

10-1
Model YFS200
Dimensions:
Overall length 1,735 mm
Overall width 1,035 mm
Overall height 1,040 mm
Seat height 740 mm
Wheelbase 1,100 mm
Ground clearance 120 mm
Minimum turning radius 3,000 mm
Basic weight:
With oil and full fuel tank 155 kg
Engine:
Engine type Air-cooled 2-stroke
Cylinder arrangement Forward-inclined single cylinder
Displacement 195 cm
3
Bore × stroke 66 ×57 mm
Compression ratio 6.6 : 1
Starting system Kick starter
Lubrication system Separate lubrication (Yamaha Autolube)
EBU00428
SPECIFICATIONS
5VM-9-61-06 3/14/03 9:40 PM Page 12

10-2
Model YFS200
Engine oil (2-cycle):
Type Air-cooled 2-stroke engine oil
Quantity 1.3 L
Transmission oil:
Type SAE 10W30 type SE motor oil
Recommended transmission oil
classificationAPI Service SE, SF, SG type or higher
cC
In order to prevent clutch slippage (since the
transmission oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD” or
oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING
II” or higher.
Quantity:
Periodic oil change 0.65 L
Air filter Wet type element
10
5VM-9-61-06 3/14/03 9:40 PM Page 13