2004 TOYOTA xA change time
[x] Cancel search: change timePage 4 of 23
REMOTE CONTROL INFORMATION
THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEM
The 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the
front and a PANIC button on the back .
The RS3200 may be controlled by as many as 4 remote controls, so you may add two additional
remote controls to the two included with your system. Contact your Scion dealer for more details.
NOTE: This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try and correct the interference by one or more
of the following measures:
t 3 F P S J F O U P S S F M P D B U F U I F S F D F J W J O H B O U F O O B
t * O D S F B T F U I F T F Q B S B U J P O C F U X F F O U I F F R V J Q N F O U B O E U I F S F D F J W F S
t $ P O O F D U U I F F R V J Q N F O U J O U P B O P V U M F U P O B D J S D V J U E J G G F S F O U G S P N U I B U
to which the receiver is connected
t $ P O T V M U U I F E F B M F S P S B O F Y Q F S J F O D F E S B E J P 5 7 U F D I O J D J B O
for help.
PROGRAMMING
IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicle’s doors when you turn the ignition key
to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. To
change the programming of this feature, follow the procedure shown below.
1. Before you begin:
Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 3
Front Button
FLASHES WHEN BUTTONS PRESSED
PUSH TO LOCK DOORS AND ARM SYSTEM PUSH TO UNLOCK DOORS AND DIS-ARM SYSTEM
Back Button
HOLD TO ACTIVATE PANIC MODE OPERATION
a. Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON). c.
The STATUS MONI TOR’S
LED (or the engine immobilizer
system’s LED) turns on for 30
seconds.
b. Turn the ignition
key backto lock.
a. Close the door =
IG. Controlled Door Locks ON
Close, then open and close
the door again = IG. Controlled
Door Locks OFF c.
The tail and marker lights
flash once and the buzzer
chirps once when the
system is set for IG door
lock control ON, twice for
IG door lock control OFF.
If this does not happen,
start over. Programming is
now complete.
b. The tail and marker lights
flash once, and the buzzer
chirps once.
123123
123123
Page 6 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the
remote control, then unlock the remaining doors when the UNLOCK button is pressed again within 3
seconds. You may change the programming so all doors will unlock at once when the UNLOCK but-
ton is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 5
BRIEF DESCRIPTION–RS3200 FEATURES
a. Insert the key into,
and remove it
from the ignition
switch 2 times.
e. Insert the key into
the ignition and
leave it in.
c. Insert the key
into, and remove
it from the ignition
switch 1 time.
g. Turn the key from
LOCK to ON 4
times (ending at
LOCK.) h.
Remove the key
from the ignition
switch.
b. Close, then open
the driver’s door
2 times.
f. Close the driver’s
door.d. Close , then open
the driver’s door
2 times.
i. The tail and marker lights flash 4 times, the
buzzer chirps 4 times , and the doors lock
and unlock 4 times.
When an alarm is TRIGGERED, the system disables the vehicle’s start -
er and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will loce the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys -
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The RS3200 flashes the vehicle’s tail and marker lights during REMOTE
ARMING and REMOTE DISARMING, as well as during an alarm. Also,
the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the RS3200 activates the vehicle’s horn.
If power tot the RS3200 is disrupted while it is ARMED, an alarm is
TRIGGERED once power is restored.
This panel houses the GLASS BREAKAGE SENSOR microphone and
the flashing LED that indicates the operating status of the security sys -
tem. (In vehicles with an engine immobilizer system, that system’s LED
and a seperate microphone are used instead.)
The RS3200 utilizes a PIEZO BUZZER, usually mounted in the engine
compartment, to sounds confirmation “chirps” and tones for function
confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle’s doors when you turn the
ignition key to “ON” or “START”, and unlocks the doors when you turn
the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
RS3200 is approximately 50 feet. Please refer to page 10 for a descrip -
tion of factors that may affect the performance (operating range) of the
remote controls.
STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED
AUTOMATIC DOOR LOCK /
UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES
FUNCTIONS
Page 7 of 23
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123
Page 16 of 23
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the system’s operation for PASSIVE
A
RMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS MONITOR’S LED turns on for 30 seconds, then
starts flashing. The system is now ARMED.
* The system will not A
RM while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 15
SCION
SECURITY
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS(PRE-ARM-ING)THEN FLASHES(SYSTEM IS ARMED)ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times. b.
Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.
a. Close, then Open the door:
2 times = P
ASSIVE ARMING OFF
3 times = P
ASSIVE ARMING ON,
0 Sec. E
NTRY DEL AY
4 times = PASSIVE ARMING ON,
15 Sec. E
NTRY DEL AY
5 times = PASSIVE ARMING ON,
30 Sec. E
NTRY DEL AY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete.
e.
Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED
123123123
123
123
123
123
123
123
Page 17 of 23
PROGRAMMING
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the driver’s door when the UNLOCK button is pressed on the
remote control, then unlock the remaining doors when the UNLOCK button is pressed again within 3
seconds. You may change the programming so all doors will unlock at once when the UNLOCK but-
ton is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 5
BRIEF DESCRIPTION–RS3200 FEATURES
a. Insert the key into,
and remove it
from the ignition
switch 2 times.
e. Insert the key into
the ignition and
leave it in.
c. Insert the key
into, and remove
it from the ignition
switch 1 time.
g. Turn the key from
LOCK to ON 4
times (ending at
LOCK.) h.
Remove the key
from the ignition
switch.
b. Close, then open
the driver’s door
2 times.
f. Close the driver’s
door.d. Close , then open
the driver’s door
2 times.
i. The tail and marker lights flash 4 times, the
buzzer chirps 4 times , and the doors lock
and unlock 4 times.
When an alarm is TRIGGERED, the system disables the vehicle’s start -
er and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will loce the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys -
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The RS3200 flashes the vehicle’s tail and marker lights during REMOTE
ARMING and REMOTE DISARMING, as well as during an alarm. Also,
the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the RS3200 activates the vehicle’s horn.
If power tot the RS3200 is disrupted while it is ARMED, an alarm is
TRIGGERED once power is restored.
This panel houses the GLASS BREAKAGE SENSOR microphone and
the flashing LED that indicates the operating status of the security sys -
tem. (In vehicles with an engine immobilizer system, that system’s LED
and a seperate microphone are used instead.)
The RS3200 utilizes a PIEZO BUZZER, usually mounted in the engine
compartment, to sounds confirmation “chirps” and tones for function
confirmation and programming step confirmation.
The RS3200 automatically locks your vehicle’s doors when you turn the
ignition key to “ON” or “START”, and unlocks the doors when you turn
the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
RS3200 is approximately 50 feet. Please refer to page 10 for a descrip -
tion of factors that may affect the performance (operating range) of the
remote controls.
STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED
AUTOMATIC DOOR LOCK /
UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES
FUNCTIONS
Page 19 of 23
REMOTE CONTROL INFORMATION
THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEM
The 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the
front and a PANIC button on the back .
The RS3200 may be controlled by as many as 4 remote controls, so you may add two additional
remote controls to the two included with your system. Contact your Scion dealer for more details.
NOTE: This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try and correct the interference by one or more
of the following measures:
t 3 F P S J F O U P S S F M P D B U F U I F S F D F J W J O H B O U F O O B
t * O D S F B T F U I F T F Q B S B U J P O C F U X F F O U I F F R V J Q N F O U B O E U I F S F D F J W F S
t $ P O O F D U U I F F R V J Q N F O U J O U P B O P V U M F U P O B D J S D V J U E J G G F S F O U G S P N U I B U
to which the receiver is connected
t $ P O T V M U U I F E F B M F S P S B O F Y Q F S J F O D F E S B E J P 5 7 U F D I O J D J B O
for help.
PROGRAMMING
IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicle’s doors when you turn the ignition key
to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or “LOCK”. To
change the programming of this feature, follow the procedure shown below.
1. Before you begin:
Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 SCION RS3200 REMOTE KEYLESS Security systemSCION RS3200 remote keyless Security system Page 3
Front Button
FLASHES WHEN BUTTONS PRESSED
PUSH TO LOCK DOORS AND ARM SYSTEM PUSH TO UNLOCK DOORS AND DIS-ARM SYSTEM
Back Button
HOLD TO ACTIVATE PANIC MODE OPERATION
a. Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON). c.
The STATUS MONI TOR’S
LED (or the engine immobilizer
system’s LED) turns on for 30
seconds.
b. Turn the ignition
key backto lock.
a. Close the door =
IG. Controlled Door Locks ON
Close, then open and close
the door again = IG. Controlled
Door Locks OFF c.
The tail and marker lights
flash once and the buzzer
chirps once when the
system is set for IG door
lock control ON, twice for
IG door lock control OFF.
If this does not happen,
start over. Programming is
now complete.
b. The tail and marker lights
flash once, and the buzzer
chirps once.
123123
123123