2004 TOYOTA TACOMA belt

’04 Tacoma U (L/O 0309)
93
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
Anchor
brackets
Double cab with rear seats
Use the anchor bracket on the back panel
to attach the top strap.
Regular cab models— Anchor brackets are installed for (each)
passenger seating position.
Double cab models— Anchor brackets are installed for each
rear seating position.
TO USE THE ANCHOR BRACKET:
Regular cab with bench seat—
1. Pull the seatback release lever and swing the seatback forward slightly,
then latch the hook onto the anchor
bracket.
Return the seatback to its original
position.2. Fix the child restraint system withthe seat belt and tighten the top
strap.
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.

’04 Tacoma U (L/O 0309)
95
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
3. Fix the child restraint system withthe seat belt and tighten the top
strap.
Replace the passenger head re-
straint.
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.
CAUTION
When returning the seatback to its
original position, make sure the
seatback is securely locked by
pushing forward and rearward on
the top of the seatback.
Make sure the top strap is securely
latched, and check that the child
restraint system is secure by push-
ing and pulling it in different direc-
tions. Follow all the installation in-
structions provided by its manufac-
turer.
Double cab with rear seats— 1. Remove the head restraint (outside position only).

’04 Tacoma U (L/O 0309)
96
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
2. Pull the seatback release lever andswing the seatback forward slightly,
then latch the hook onto the anchor
bracket.
Return the seatback to upright posi-
tion.3. Fix the child restraint system withthe seat belt and tighten the top
strap.
Replace the head restraint (outside
position only).
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.
CAUTION
When returning the seatback to its
original position, make sure the
seatback is securely locked by
pushing forward and rearward on
the top of the seatback. Failure to
do so will prevent the seat belt
from operating properly.
Make sure the top strap is securely
latched, and check that the child
restraint system is secure by push-
ing and pulling it in different direc-
tions. Follow all the installation in-
structions provided by its manufac-
turer.

’04 Tacoma U (L/O 0309)
98
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
Symbol mark
TO USE THE ANCHOR BRACKET:
Front outside position—1. Remove the passenger head re- straint.
Lightly push down on the top sur-
face of the anchor bracket cover
with the symbol mark shown in the
illustration, then pull it forward to
remove.2. Fix the child restraint system withthe seat belt.
Latch the hook onto the anchor
bracket on the back panel and tight-
en the top strap.
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instructions
provided by its manufacturer.

’04 Tacoma U (L/O 0309)
99
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
3. Replace the head restraint.
Store the removed cover in a safe place
such as the glove box.
Be sure to replace the cover when the
anchor bracket is not in use.Front center position—
Fix the child restraint system with the
seat belt.
Latch the hook onto the rear lower an-
chor bracket and tighten the top strap.
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instructions
provided by its manufacturer.

’04 Tacoma U (L/O 0309)
100
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
Symbol mark
Rear outside position—1. Lightly push down on the top sur- face of the anchor bracket cover
with the symbol mark shown in the
illustration, then pull it forward to
remove.
Routing
device
2. Fix the child restraint system withthe seat belt.
Route the top strap through the
routing device as shown in the il-
lustration.
For instructions on installing the child re-
straint system, see “Child restraint” in this
Section.
CAUTION
Make sure the top strap is not
twisted.
3. Latch the hook onto the rear lower anchor bracket and tighten the top
strap.
Store the removed cover in a safe place
such as the glove box.
Be sure to replace the cover when the
anchor bracket is not in use.

’04 Tacoma U (L/O 0309)
101
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
CAUTION
Make sure the top strap is securely
latched, and check that the child re-
straint system is secure by pushing
and pulling it in different directions.
Follow all the installation instructions
provided by its manufacturer.
Separate seats
Split bench seats
Nonsplit bench seat
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the right passenger ’s seat-
ing position.
Child restraint systems complying with the
FMVSS225 or CMVSS210.2 specification
can be fixed to these anchorages. In this
case, it is not necessary to fix the child
restraint system with a seat belt on the
vehicle.
—Installation with child
restraint lower anchorages
(regular cab and xtracab models)

’04 Tacoma U (L/O 0309)
103
2004 TACOMA from Sep. ’03 Prod. (OM35814U)
For the installation details, refer to the
instruction manual equipped with each
product.
CAUTION
When using the lower anchorages
for the child restraint system, be
sure that there are no irregular ob-
jects around the anchorages or that
the seat belt is not caught.
Push and pull the child restraint
system in different directions to be
sure it is secure. Follow all the
installation instructions provided by
its manufacturer.
After securing the child restraint
system, never slide or recline the
seat.
Vehicles with passenger airbag
manual onoff switch—
Child restraint system should never
be installed on the front passenger
seat with the passenger airbag
manual onoff switch in the “ON”
position, because the force of the
deploying airbag could cause death
or serious injury to the child in for-
ward seating position.
Lower anchorages for the child restraint
systems complying with the FMVSS225
or CMVSS210.2 specifications are
installed in the outside positions of the
rear seat.
Child restraint systems complying with the
FMVSS225 or CMVSS210.2 specification
can be fixed with these anchorages. In
this case, it is not necessary to fix the
child restraint system with a seat belt on
the vehicle.
Canada only
Ty p e A
—Installation with child
restraint lower anchorages
(double cab models)