2004 SUZUKI GRAND VITARA Changing a tire

YH4
GRAND
VITARA
3A-2 FRONT END ALIGNMENT
CAMBER
Camber is the tilting of the front wheels from the vertical, as viewed from the front of the vehicle. When the wheels
tilt outward at the top, the camber is positive. When the wheels tilt inward at the top, the camber is negative. The
amount of tilt is measured in degrees.
PRELIMINARY CHECKS PRIOR TO ADJUSTING FRONT ALIGNMENT
Steering and vibration complaints are not always the result of improper alignment. An additional item to be checked
is the possibility of tire lead due to worn or improperly manufactured tires. ªLeadº is the deviation of the vehicle from
a straight path on a level road without hand pressure on the steering wheel.
Section 3 of this manual contains a procedure for determining the presence of a tire lead problem.
Before making any adjustment affecting toe setting, the following checks and inspections should be made to en-
sure correctness of alignment readings and alignment adjustments:
1) Check all tires for proper inflation pressures and approximately the same tread wear.
2) Check for loose ball joints. Check tie rod ends; if excessive looseness is noted, it must be corrected before ad-
justing.
3) Check for run-out of wheels and tires.
4) Check vehicle trim heights; if out of limits and a correction is to be made, it must be made before adjusting toe.
5) Check for loose control arms.
6) Check for loose or missing stabilizer bar attachments.
7) Consideration must be given to excess loads, such as tool boxes. If this excess load is normally carried in ve-
hicle, it should remain in vehicle during alignment checks.
8) Consider condition of equipment being used to check alignment and follow manufacturer's instructions.
9) Regardless of equipment used to check alignment, vehicle must be on a level surface both fore and aft and
transversely.
TOE ADJUSTMENT
Toe is adjusted by changing tie rod length. Loosen right and left tie
rod end lock nuts first and then rotate right and left tie rods by the
same amount to align toe-in to specification.
In this adjustment, right and left tie rods should become equal in
length.
After adjustment, tighten lock nuts to specified torque.
Tightening Torque
(a): 65 N
.m (6.5 kg-m, 47.0 lb-ft)
CAMBER AND CASTER ADJUSTMENT
Should camber or caster be found out of specifications upon in-
spection, locate its cause first. If it is in damaged, loose, bent,
dented or worn suspension parts, they should be replaced. If it is
in body, repair it so as to attain specifications.
To prevent possible incorrect reading of camber or caster, vehicle
front end must be moved up and down a few times before inspec-
tion.

YH4
GRAND
VITARA
WHEELS AND TIRES 3F-7
TIRE
MOUNTING AND DEMOUNTING
Use tire changing machine to mount or demount tires. Follow equip-
ment manufacturer's instructions. Do not use hand tools or tire
irons alone to change tires as they may damage tire beads or wheel
rim.
Rim bead seats should be cleaned with wire brush or coarse steel
wool to remove lubricants, old rubber and light rust. Before mount-
ing or demounting tire, bead area should be well lubricated with ap-
proved tire lubricant.
After mounting, inflate to 240 kPa (35psi) so that beads are com-
pletely seated. Then adjust pressure to specified shown an tire
placard.
WARNING:
Do not stand over tire when inflating. Bead may break when
bead snaps over rim's safety hump and cause serious per-
sonal injury.
Do not exceed 240 kPa (35 psi) pressure when inflating. If
240 kPa (35 psi) pressure will not seat beads, deflate, re-lu-
bricate and reinflate. Over inflation may cause bead to break
and cause serious personal injury.
Install valve core and inflate to proper pressure.
TIRE REPAIR
There are many different materials and techniques on the market
to repair tires. As not all of these work on all types of tires, tire
manufacturers have published detailed instructions on how and
when to repair tires. These instructions can be obtained from the
tire manufacturer.

YH4
GRAND
VITARA
5A-18 BRAKES PIPE / HOSE / MASTER CYLINDER
1. LSPV spring bolt
2. LSPV bolt
3. Brake pipe flare nut
4. Air bleeding plug
1. LSPV lever
2. Stopper bolt (if equipped)
3. Coil spring ªAº: Don't turn(a)
2) Torque each bolt and nut to specification as indicated respec-
tively in figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft) (brake flare nut)
(c): 7.5 N
.m (0.75 kg-m, 9.0 lb-ft) (bleeder plug)
3) Upon completion of installation, fill reservoir tank with specified
fluid and bleed air from brake system.
NOTE:
Make sure to bleed air from LSPV bleeder without failure.
4) After bleeding air, check that LSPV is installed properly, referring
to following INSPECTION & ADJUSTMENT.
INSPECTION & ADJUSTMENT
Confirm the following before inspection and adjustment.

Fuel tank is filled with fuel fully.

Vehicle is equipped with spare tire, tools, jack and jack handle.

Vehicle is free from any other load.
With vehicle in above conditions;
1) Place it on level floor.
2) Push up (for 5 door model) or push down (for 3 door model)
LSPV lever with finger till it stops and measure length ªLº of coil
spring as it is pulled.
3) Spring length ªLº should be the value specified below.
Spring length (between spring end and spring bolt)
ªLº: 103 mm (4.06 in.) (5 door model). . . . .
ªLº: 157 mm (6.18 in.) (3 door model). . . . .
4) If it isn't, adjust it to specification by changing stay positions as
shown in figure. After adjustment, tighten bolt to specified
torque.
For details, refer to left figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
NOTE:
Check to make sure that LSPV body and brake pipe joints
are free from fluid leakage. Replace defective parts, if any.