2004 SUZUKI GRAND VITARA lamp

YH4
GRAND
VITARA
5E1-38 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Clamps
2. Sensor bolt
SENSOR INSPECTION

Check sensor (pole piece) for damage or bent.

Check sensor for resistance.
Resistance between
terminals : 1.2 ± 1.6 k
at 20C, 68F
Resistance between
terminal and sensor body: 1 M
or more
If any faulty is found, replace.
SENSOR ROTOR INSPECTION

Check rotor serration (teeth) for being missing, damaged or de-
formed.

Turn wheel and check if rotor rotation is free from eccentricity and
looseness.

Check that no foreign material is attached.
If any faulty is found, repair or replace.
INSTALLATION
1) Check that no foreign material is attached to sensor and rotor.
2) Install it by reversing removal procedure.
Tightening Torque
(a): 21 N
.m (2.1 kg-m, 15.0 lb-ft)
CAUTION:
Do not pull wire harness or twist more than necessary
when installing rear wheel speed sensor.
3) Check that there is no clearance between sensor and knuckle.

YH4
GRAND
VITARA
1. Bolt
2. Console box
bracket
3. Boot cover
1. Boot No. 3
2. Boot cover
3. Boot No. 2
4. Control lever
5. Lever case
6. Control case cover
7. Boot No. 1
1. Transmission control
lever locating bolt
2. Transfer control lever
locating bolt
7A-4 MANUAL TRANSMISSION (TYPE 1)
SHIFT CONTROL LEVERS
REMOVAL
1) Remove 4 screws at the front and rear and 2 clips at the center
then take off front and rear center console boxes.
NOTE:
To remove clip, push in its center pin first.
2) Remove console box bracket by removing bolts and lift up boot
cover and boot No. 2.
3) Remove boot clamp and then remove boot No. 1 from transmis-
sion shift lever case.
4) With gear shift control case cover pushed down with fingers, turn
it to counter clockwise and take out shift control lever.
5) Take out transfer shift control lever in similar manner as de-
scribed above.
INSPECTION AND INSTALLATION
1) Check shift control lever lower portion and control lever locating
sheet for excessive wear, and boot for damage. Correct or re-
place if necessary.
2) Apply grease to pivot portions and seat, then install shift control
lever.
ªAº: Grease 99000-25010
3) Perform above steps also for transfer shift control lever.
4) If control lever locating bolts (a) are replaced or retightened,
torque them as specified below.
Replacing of control lever locating bolts requires thread lock ce-
ment.
ªBº: Cement 99000-32020
Tightening Torque
(a): 17 N
.m (1.7 kg-m, 12.5 lb-ft)

YH4
GRAND
VITARA
1. Boot No. 1
2. Boot clamp
3. Boot cover
4. Boot No. 2
1. Transfer boot No. 1
2. Boot clamp
1. Console box
bracket
2. Boot cover
3. Boot No. 3
MANUAL TRANSMISSION (TYPE 1) 7A-5
5) Install transmission boot No. 1 from inside of cabin and clamp
it with a new clamp securely.
6) Install transfer boot No. 1 securely on lift and clamp it by using
a new clamp.
7) Tighten transmission boot No. 2 with boot cover and console box
bracket.
Tightening Torque
(a): 6 N
.m (0.6 kg-m, 4.0 lb-ft)
8) Install console box.
NOTE:
Be sure that flare end of transmission boot No. 3 is engaged
with console box.

YH4
GRAND
VITARA
7A-6 MANUAL TRANSMISSION (TYPE 1)
3, (a)
1. Coupler
2. Clamp3. 4WD switch
4. Boot No. 2
1. Back up light switch
2. 4WD switch
1. Back up light switch coupler
2. Front propeller shaft
SWITCHES
TRANSFER 4WD SWITCH
1) Remove console box and lift transmission control lever boots
No. 2 and No. 3. (Refer to page 7A-4.)
2) Remove transfer control lever boot No. 2, unclamp wiring on
transfer case to free it and pull off coupler.
3) Replace switch and connect as it was.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft)
4) Turn ON ignition switch, shift transfer shift control lever to 4WD
position and check that indicator lights. Turn OFF switch after
checking.
NOTE:

When removing and reinstalling switch, use care not to let
dust enter transfer box inside.

Make sure to reset clamp for wiring which is located
where invisible directly.

It is recommended to work on transfer shift control lever
boot No. 1 from underside of vehicle on lift.

Identify this switch by its leg part which is different for that
of back up light switch.
BACK UP LIGHT SWITCH
WARNING:
Refrain from work while exhaust center pipe is hot.
REMOVAL AND INSTALLATION
NOTE:
When replacing switch, use care not to let dust enter transmis-
sion through switch hole.
1) Lift up vehicle.
2) Remove coupler(s) for switch wiring.

YH4
GRAND
VITARA
1. Back up light switch
2. Exhaust center pipe
1. Ohmmeter
2. Back up light switch or 4WD switch1, (a)
[Type 1]
[Type 2]
MANUAL TRANSMISSION (TYPE 1) 7A-7
3) Replace switch, connect and clamp as they were.
Tightening Torque
(a): 20 N
.m (2.0 kg-m, 14.5 lb-ft) (Type 1)
(a): 45 N
.m (4.5 kg-m, 32.5 lb-ft) (Type 2)
4) When back up light switch has been replaced, check switch for
proper function with ignition switch turned ON and gear shifted
to reverse position. Turn OFF switch after checking its function.
INSPECTION OF 4WD SWITCH AND BACK UP LIGHT
SWITCH
1) Undo clamp and disconnect coupler of back up light switch
and / or 4WD switch.
2) Function of back up light switch can be checked as shown in fig-
ure.
There should be conduction at these terminals only when shift
lever is shifted to reverse position.
3) Function of transfer 4WD switch can be checked in the same
manner as back up light switch.
There should be conduction at these terminals when shift lever
is shifted to 4H, and 4L positions.
Upon completion of check, connect coupler and clamp wiring har-
ness as they were.
NOTE:
When replacing switch(es), use care not to let dust enter trans-
mission through switch hole(s).

YH4
GRAND
VITARA
1. Transmission
2. Breather clamp
3. Breather hose
4. Wiring harness clamp
5. Intake manifold
MANUAL TRANSMISSION (TYPE 1) 7A-9
DISMOUNTING OF TRANS. UNIT
IN CABIN
Remove transmission shift control lever (refer to page 7A-4) and
transfer shift control lever knob.
IN ENGINE ROOM
1) Disconnect negative (±) cable of battery.
2) Remove breather hose from clamp at the rear end of cylinder
head.
3) Remove starting motor fixing bolts and nut and then remove
starter.
4) Remove transmission fastening bolts.

YH4
GRAND
VITARA
1. Match mark
1. Flange bolt
2. Front propeller shaft
1. Transmission jack
2. Engine rear mounting member
7A-10 MANUAL TRANSMISSION (TYPE 1)
ON LIFT
1) Drain oil from transmission and transfer.
2) Give match marks on joint flange and propeller shaft as shown
in figure. (front and rear)
3) Remove flange bolts of rear propeller shaft universal joint and
pull out propeller shaft.
4) Remove flange bolts of front propeller shaft universal joint and
pull out propeller shaft.
5) Remove clutch operating cylinder from transmission. It is not
necessary to disconnect clutch hose from operating cylinder.
NOTE:

It is not necessary to drain transmission oil when dis-
mounting transmission and transfer for clutch mainte-
nance only.

Work without draining transfer oil is possible if front pro-
peller shaft is dismounted together with transmission and
transfer.
6) Remove clutch housing lower plate.
7) Disconnect couplers from 4WD switch, back up light switch and
speed sensor assembly and release their harness from clamps.
Remove nuts from joint with engine.
8) Apply transmission jack and remove engine rear mounting
member taking off its bolts.
9) After removing mounting member, move rearward transmission
and transfer assemblies placed on jack and then lower them.

YH4
GRAND
VITARA
1. Match mark
7A-12 MANUAL TRANSMISSION (TYPE 1)
REMOUNTING OF TRANS. UNIT
For remounting, reverse dismounting procedure.
Use specified torques as given below.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

For tightening torque of transmission stiffener bolt, refer to
ªENGINE MECHANICALº section.

Set each clamp for wiring, hose and cable securely.

Set clamp for shift control lever boots securely.

After installing clutch operating cylinder, check clutch pedal free
travel. Refer to SECTION 7C1 ªCLUTCHº.

Fill gear oil to transmission and transfer as specified.

Connect battery and check function of engine, clutch and trans.

When installing propeller shaft, align the match marks.