2004 SUZUKI GRAND VITARA window

YH4
GRAND
VITARA
Terminal
Operation
If mirror heater is not equipped
If mirror heater is equipped
8D-30 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR MIRROR CONTROL SYSTEM
INSPECTION
MIRROR SWITCH
1) Remove mirror switch from instrument panel.
2) Check for continuity between terminals at each switch position
as shown below.
If check result is not as specified, replace mirror switch.
DOOR MIRROR ACTUATOR
1) Remove garnish from door.
2) Disconnect door mirror coupler.
3) Check that door mirror operates properly when battery voltage
is applied to connector terminals.
Connect battery positive and negative terminal to the door mirror
terminal shown below and check operation.
If it does not operate as specified in table below, replace door
mirror assembly.
VBlYVBlY
Up

Down

Left

Right

NOTE:
When installing door mirror to door, be careful not to pinch
harness between door and door mirror.

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-31
DOOR MIRROR HEATER (IF EQUIPPED)
INSPECTION
MIRROR HEATER SWITCH
1) Remove mirror heater switch from instrument panel.
2) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
MIRROR HEATER (IF EQUIPPED)
1) Remove garnish from door.
2) Disconnect door mirror coupler.
3) Check for continuity between terminals ªaº and ºbº.
If not continuity, replace outside mirror.

YH4
GRAND
VITARA
8D-32 WINDOWS, MIRRORS, SECURITY AND LOCKS
3. To open
4. To close
3. Left turn
4. Right turn
Terminal
Switch
Terminal
Switch
POWER SLIDING ROOF (IF EQUIPPED)
INSPECTION
SLIDING ROOF SWITCH
Check switch for continuity between terminals as shown below.
Slide Switch (1)
CDFCDF
OPEN
OFF
CLOSE
Tilt Switch (2)
EDBEDB
UP
OFF
DOWN
SLIDING ROOF MOTOR ASSEMBLY
1) Remove head lining. Refer to Section 9 for detail.
2) Remove sliding roof motor assembly (1).
3) Connect known-good sliding roof switch (2) to sliding roof motor
assembly.
4) Connect 12 V battery positive terminal to terminal ªAº of motor
assembly (1) and battery negative terminal to terminal ªBº of mo-
tor assembly (1).
5) Check that the sliding roof motor (1) runs according to the move-
ment of the sliding roof switch (2).
Sliding Roof Switch
Motor
Tilt upturns left
Tilt downturns right
Slide openturns right
Slide closeturns left
If motor does not operate as above, replace sliding roof motor
assembly (1).

YH4
GRAND
VITARA
Hard Top Model
Canvas Top Model
LOAD2 LOAD1
1. Heater wire
2. Thermostat
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-33
FRONT SEAT HEATER (IF EQUIPPED)
SEAT HEATER SWITCH (DRIVER AND PASSENGER SIDE)
INSPECTION
1) Confirm that ignition switch is OFF position.
2) Pull out seat heater switch from front center console box.
3) Disconnect seat heater switch coupler.
4) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace.
SEAT HEATER WIRE
INSPECTION
1) Confirm that seat heater switch is OFF position.
2) Disconnect two couplers of seat heater under the seat cushion.
(If seat under tray is equipped, pull out coupler between tray and
seat cushion.)
3) Check for continuity between terminals as shown below.
If not continuity, replace faulty seat heater.
Hard Top Model
Seat heater circuit in seat back
Between a and b
Between b and d
Between c and e
Seat heater circuit in seat cushion
Between f and g
Canvas Top Model
Seat heater circuit in seat back
Between A And B
Seat heater circuit in seat cushion
Between C and D
Between D and F
Between E and G

YH4
GRAND
VITARA
9
BODY SERVICE 9-1
GLASS, WINDOWS AND MIRRORS9- 2 . . . . .
Front Door Glass 9- 2. . . . . . . . . . . . . . . . . . . . .
Front Door Window Regulator 9- 5. . . . . . . . . .
Windshield 9- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass 9-12. . . . . . . . . . . . . . . . . . . . .
Rear Door Window Regulator 9-14. . . . . . . . . .
Quarter Window 9-15. . . . . . . . . . . . . . . . . . . . . .
Back Door Glass 9-16. . . . . . . . . . . . . . . . . . . . .
BODY STRUCTURE9-17 . . . . . . . . . . . . . . . . . . .
Front Door Assembly 9-17. . . . . . . . . . . . . . . . .
Rear Door Assembly 9-18. . . . . . . . . . . . . . . . . .
Back Door / Rear Gate Assembly 9-19. . . . . . . .
Hood 9-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Fender 9-22. . . . . . . . . . . . . . . . . . . . . . . . .
Front Bumper 9-23. . . . . . . . . . . . . . . . . . . . . . . .
Rear Bumper 9-24. . . . . . . . . . . . . . . . . . . . . . . .
Under Body Dimensions 9-25. . . . . . . . . . . . . . .
Body Dimensions 9-26. . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER
INFORMATION9-33 . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9-33. . . . . . . . . . . . . . . . . . . . .
SEAT9-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat 9-34. . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Seat 9-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAINT AND COATINGS9-36 . . . . . . . . . . . . . . . .
Anti-Corrosion Treatment 9-36. . . . . . . . . . . . . .
Metal Replacement Parts Finishing 9-37. . . . .
Plastic Parts Finishing 9-58. . . . . . . . . . . . . . . . .
SECURITY AND LOCKS9-59 . . . . . . . . . . . . . . . .
Front Door Lock Assembly 9-59. . . . . . . . . . . . .
Rear Door Lock Assembly 9-61. . . . . . . . . . . . .
Back Door / Rear Gate Lock Assembly 9-62. . .
Key Coding 9-63. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF / CONVERTIBLE TOP9-64 . . . . . . . . .
Sliding Roof (if equipped) 9-64. . . . . . . . . . . . . .
Canvas Top And Topbow Frames 9-71. . . . . . .
EXTERIOR AND INTERIOR TRIM9-72 . . . . . . .
Floor Carpet 9-72. . . . . . . . . . . . . . . . . . . . . . . . .
Head lining 9-73. . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Trim (2 Door Model) 9-75. . . . . . . . . . . . . .
Side Moldings (if equipped) 9-77. . . . . . . . . . . .
Splash Guard (if equipped) 9-78. . . . . . . . . . . .
Roof Rail (if equipped) 9-79. . . . . . . . . . . . . . . .
Roof Molding 9-79. . . . . . . . . . . . . . . . . . . . . . . .
Luggage Under Box 9-80. . . . . . . . . . . . . . . . . .
SECTION 9
BODY SERVICE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

When body servicing, if shock may be applied to air bag system component parts, remove those parts
beforehand. (Refer to Section 10B.)
NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital components and
systems, and / or could result in major repair expense. They must be replaced with one of the same part
number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.
CONTENTS

YH4
GRAND
VITARA
6. Door trim
7. Door hinge
8. Door open stop
9. Door sealing cover
10. Window regulator handle (if equipped) 1. Door glass
2. Weatherstrip
3. Opening weatherstrip
4. Window regulator
5. Glass run
9-2 BODY SERVICE
GLASS, WINDOWS AND MIRROR
FRONT DOOR GLASS

YH4
GRAND
VITARA
1. Screws 1. Door outside weatherstrip
2. Screw1. Door inside pull handle bracket
BODY SERVICE 9-3
REMOVAL
1) Remove inside handle bezel.
2) Remove door mirror bezel (if equipped).
3) Remove inside lock knob and door inside pull handle case fitting
screw.
3-1) Remove window regulator handle (if equipped).
To remove regulator handle, pull off snap ring by using a cloth
as shown below.
4) Remove door trim.
With inside handle bezel tilted as shown in figure, turn door trim
90
counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
5) Remove door inside pull handle bracket.
6) Remove door sealing cover.
7) Remove door outside weatherstrip.
Lower window all the way down. Then, use a tape-wrapped putty
knife (or screwdriver) to pry off weatherstrip.
CAUTION:
Use a tape-wrapped putty knife (or screwdriver) to pry off
weatherstrip. Use of an unwrapped tool will cause dam-
age to painting.
8) Remove glass attaching screws.
9) Take out door glass.

YH4
GRAND
VITARA
1. Screws
1. Bolts
1. Door sealing cover
2. Adhesive1, (a)
9-4 BODY SERVICE
INSTALLATION
Reverse removal procedure to install door glass noting following
points:

Tighten glass attaching screws to specified torque. Tighten front
screw first, then rear screw.
Tightening Torque
(a): 2.5 N
.m (0.25 kg-m, 1.8 lb-ft)

When window becomes hard to raise and lower, adjust screws to
correct tilted glass as shown in figure.

Adjust equalizer of window regulator so that measurement A and
B are equal.

Secure door sealing cover with adhesive.