2004 SUZUKI GRAND VITARA power steering fluid

YH4
GRAND
VITARA
3B1-24 POWER STEERING (P / S) SYSTEM
1. Pump cover
1. Pressure switch
1. Suction connector
2. O-ring
1. Suction connector
15) Gradually tighten new pump cover bolts to specified torque.
NOTE:
After installing pump cover, check to make sure that shaft
can be turned by hand.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
16) Apply power steering fluid to O-ring of terminal switch.
17) Install pressure switch to pump body.
Tightening Torque
(a): 28 N
.m (2.8 kg-m, 20.0 lb-ft)
18) Apply power steering fluid to relief valve (flow control valve).
19) Install relief valve (flow control valve) to pump body.
20) Install flow control spring.
21) Apply power steering fluid to O-rings of plug.
22) Install O-rings to plug.
23) Tighten plug to specified torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
24) Apply power steering fluid to O-ring of suction connector.
25) Install O-ring to suction connector.
26) Install suction connector to pump body as shown in figure.
Tighten new suction connector bolts to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-25
INSTALLATION
Reverse removal procedure, and then noting the following instruc-
tions.

For tightening torques, refer to structural diagram on previous
page.

Adjust power steering pump drive belt by referring to ªBELT TEN-
SION ADJUSTMENTº under ªPOWER STEERING PUMP
DRIVE BELTº in this section.

Fill specified power steering fluid after installation and bleed air
without failure. (Refer to ªAIR BLEEDING PROCEDUREº in this
section.)

YH4
GRAND
VITARA
3B1-26 POWER STEERING (P / S) SYSTEM
09915-77420
Oil pressure gauge
attachment and hose set09915-77410
Oil pressure gauge09943-55010
Boot clamp plier
TIGHTENING TORQUE SPECIFICATION
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Gear box mounting bolts555.540.0
Gear box cylinder pipe flare nuts292.921.0
Gear box low pressure pipe union bolt404.029.0
Gear box high pressure pipe union bolt353.525.5
Tie-rod end lock nut656.547.0
G16 Type engine555.540.0
Pump bracket boltJ20 Type engine252.518.5
H25 Type engine454.532.5
Pump union bolt606.043.5
Oil pump mount bolts252.518.5
Pipe clamp bolt / Reservoir bracket bolt111.18.0
Steering shaft joint bolt252.518.0
High pressure flare nuts404.029.0
Pump cover bolts232.317.0
Plug606.043.5
Pressure switch (Terminal)282.820
Suction connector bolt101.07.5
Tie-rod end nut484.835.0
Tie-rod (for canvas top LH model only)858.561.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Lithium greaseSUPER GREASE (A)
(99000-25010)
Oil seal lip of P / S pump pulley shaft
Power steering fluidAn equivalent of DEXRON
-III or
DEXRON
-II

To fill P / S fluid reservoir

Parts lubrication when installing
SPECIAL TOOL