2004 SUZUKI GRAND VITARA ECO mode

[x] Cancel search: ECO mode

coolant mirror controls reset sun roof fuel tank removal diagnostic menu wipers

Load previous 8 pages

Page 536 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-5
CLEARANCE, TAIL AND LICENCE PLATE LIGHTS
TroublePossible causeCorrection
All lights do not lightªTAILº fuse blown
Lighting switch faulty
Wiring or grounding

Page 546 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
8C-4 INSTRUMENTATION / DRIVER INFORMATION
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).

Page 547 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
INSTRUMENTATION / DRIVER INFORMATION 8C-5
BRAKE AND PARKING BRAKE WARNING LIGHT
TroublePossible CauseCorrection
Brake warning light does
not light upBulb in combination meter blown

Page 560 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-5
DIAGNOSIS
NOTE:
Fuse name (ª º) in the table below is shown on the fuse box cover (Hard Top Model) or the junction box
(Canvas Top Model).

Page 561 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
8D-6 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED)
TroublePossible causeCorrection
All power doors are not
locked / unlocked by both
d

Page 563 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
8D-8 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR MIRROR CONTROL SYSTEM
TroublePossible causeCorrection
All power mirrors do not
operateªCIGARº fuse blown (Hard Top Model)
ªCIG

YH4
GRAND
VITARA
8D-8 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR MIRROR CONTROL SYSTEM
TroublePossible causeCorrection
All power mirrors do not
operateªCIGARº fuse blown (Hard Top Model)
ªCIGº fuse blown (Canvas Top Model)
Power door mirror switch faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
One power mirror does
not operatePower door mirror switch faulty
Actuator (power door mirror motor) faulty
Wiring or grounding faultyReplace switch
Replace actuator
Repair
DOOR MIRROR HEATER (IF EQUIPPED)
TroublePossible causeCorrection
The surface of mirror is
not defrosted although
door mirror heater
switch is ONªREAR DEFGº fuse blown (Hard Top Model)
ªDEFº fuse blown (Canvas Top Model)
Door mirror heater switch faulty
Door mirror heater faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace outside mirror
Repair
POWER SLIDING ROOF (IF EQUIPPED)
TroublePossible causeCorrection
Sliding roof does not
operate (sliding roof
motor runs OK)Foreign object stuck in sliding roof rail
Misinstallation of sliding roof rail
Conflicts of sliding roof parts
Misinstallation of sliding roof drive cableRemove or clean stuck object
Install correctly
Fix conflicts
Install correctly
Sliding roof does not
operate (sliding roof
motor does not run)ªSUN ROOFº fuse blown
Sliding roof switch faulty
Sliding roof motor ass'y faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace motor
Repair
FRONT SEAT HEATER (IF EQUIPPED)
TroublePossible causeCorrection
Both seat back and
cushion do not become
hot although seat heater
switch is LO / HI positionªSEAT HTRº fuse blown (Hard Top Model)
ªS / Hº fuse blown (Canvas Top Model)
Seat heater switch faulty
Seat heater circuit in seat back and / or seat
cushion faulty
Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace heater front back and /
or heater front cushion
Repair
Only seat back does not
become hot although seat
heater switch is HI
positionSeat heater circuit in seat back faulty
(Hard Top Model)
Seat heater circuit in seat back and / or seat
cushion faulty (Canvas Top Model)
Seat heater switch faulty
Wiring faultyReplace heater front back
Replace heater front back
and / or heater front cushion
Replace switch
Repair
Only seat cushion does
not become hot although
seat heater switch is HI
positionSeat heater circuit in seat back and / or seat
cushion faulty (Hard Top Model)
Seat heater circuit in seat cushion
(Canvas Top Model)
Seat heater switch faulty
Wiring faultyReplace heater front back
and / or heater front cushion
Replace heater front cushion
Replace switch
Repair

Page 616 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
8G-28 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
1
1. Ignition key with built-in transponder 1. Data link connector (DLC)
HOW TO REGISTER IGNITION KEY
Register the ignition key with a b

YH4
GRAND
VITARA
8G-28 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
1
1. Ignition key with built-in transponder 1. Data link connector (DLC)
HOW TO REGISTER IGNITION KEY
Register the ignition key with a built-in transponder in Immobilizer
Control Module by using the following procedure.
1) Prepare Suzuki scan tool (TECH 1A kit and cartridge for immobi-
lizer control system).
2) With ignition switch OFF, connect Suzuki scan tool to data link
connector (DLC) located on underside of instrument panel at
driver's seat side.
Special Tool
(A): 09931-76011 (Tech 1A)
(B): Immobilizer cartridge
(C): 09931-76030 (16 / 14-pin DLC cable)
NOTE:
For operation procedure of Suzuki scan tool, refer to Suzuki
scan tool operator's manual.
3) Prepare ignition key with a built-in transponder. And then turn
ignition switch ON by using it.
4) Number of Transponder codes for ignition key with a built-in
transponder that can be registered in Immobilizer Control Mod-
ule is limited to 4. If needed, clear all Transponder codes for igni-
tion key with a built-in transponder that have been registered in
Immobilizer Control Module by executing the ªCLR. TRANS
COD (CLEAR TP CODE)º command in the SELECT MODE
menu by using Suzuki scan tool.
NOTE:
When ªCLR. TRANS COD (CLEAR TP CODE)º command is
executed with the malfunction indicator lamp (the lamp for
vehicles equipped with the monitor coupler) ON or the im-
mobilizer indicator lamp (the lamp for vehicle not equipped
with the monitor coupler) ON, it remains ON even after
execution of that command is over. It will start flashing
when the ignition switch is turned OFF once and then
turned ON after some seconds.
5) Using Suzuki scan tool, register Transponder code in Immobiliz-
er Control Module by executing ªENT. TRANS COD (ENT. TP
CODE)º command in SELECT MODE menu.
6) [Vehicle equipped with monitor coupler]
Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
[Vehicle not equipped with monitor coupler]
Make sure that immobilizer indicator lamp lights when ignition
switch is turned OFF once and then ON.

Page 617 of 801

SUZUKI GRAND VITARA 2004 2.G Service Workshop Manual YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-29
7) If any other Transponder code for ignition key with a built-in
transponder needs to be registered, repeat above Steps 3), 5)
and 6).

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-29
7) If any other Transponder code for ignition key with a built-in
transponder needs to be registered, repeat above Steps 3), 5)
and 6).
NOTE:
Up to 4 Transponder codes for ignition key with a built-in
transponder can be registered.
It is not possible to register the same Transponder code
for ignition key with a built-in transponder as the one al-
ready registered in Immobilizer Control Module.
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT
When Immobilizer Control Module was replaced, including when
replaced because rechecking by using a known-good Immobilizer
Control Module was necessary during trouble diagnosis, register
Transponder code and ECM / Immobilizer Control Module code in
Immobilizer Control Module and ECM / Immobilizer Control Module
code in ECM/PCM by performing following procedure.
1) Perform Steps 1) and 2) described in ªHow to register ignition
keyº section.
2) Prepare ignition key with a built-in transponder. And then turn
ignition switch ON by using it.
3) Using Suzuki scan tool, clear all transponder codes registered
in Immobilizer Control Module by executing ªCLR. TRANS COD
(CLEAR TP CODE)º command in SELECT MODE menu.
NOTE:
When ªCLR. TRANS COD (CLEAR TP CODE)º command is
executed with the malfunction indicator lamp (the lamp for
vehicles equipped with the monitor coupler) ON or the im-
mobilizer indicator lamp (the lamp for vehicles not
equipped with the monitor coupler) ON, it remains ON even
after execution of that command is over. It will start flashing
when the ignition switch is turned OFF once and then
turned ON after some seconds.
4) Using Suzuki scan tool, register Transponder code in Immobiliz-
er Control Module by executing ªENT. TRANS COD (ENT. TP
CODE)º command in SELECT MODE menu.
5) Using Suzuki scan tool, register ECM / Immobilizer Control Mod-
ule code in both Immobilizer Control Module and ECM / PCM by
executing ªRECORD ECU (RECORD ECM / PCM / ICM)º com-
mand in SELECT MODE menu.
6) [Vehicle equipped with monitor coupler]
Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
[Vehicle not equipped with monitor coupler]
Make sure that immobilizer indicator lamp lights when ignition
switch is turned OFF once and then ON.
7) If any other Transponder code for ignition key with a built-in trans-
ponder needs to be registered, repeat above Steps 2), 4) and 6).
NOTE:
Up to 4 Transponder codes for ignition key with a built-in
transponder can be registered.
It is not possible to register the same Transponder code
for ignition key with a built-in transponder as the one al-
ready registered in Immobilizer Control Module.

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 next >

ignition child seat lights navigation update USB wheel bolts