2004 SUZUKI GRAND VITARA Lock

YH4
GRAND
VITARA
7B1-78 AUTOMATIC TRANSMISSION (4 A / T)
ON-VEHICLE
SERVICE MOUNTING
EXTERNAL
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
Fastening portion
Tightening torque
Fastening portion
N´mkg-mlb-ft
Automatic transmission fluid drain plug232.317.0
Transfer oil filler / level and drain plugs232.317.0
Transmission case plug171.712.5
Manual select lever nut131.39.5
Manual select cable nut70.75.5
Manual selector assembly bolts181.813.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts
Engine rear mounting member bolts
Transmission case right stiffener bolts
505.036.5
Universal joint flange bolts and nuts505.036.5
Torque converter mounting bolts656.547.0
Adapter case or extension case bolts
(G16 engine)353.525.5
Adapter case or extension case bolts
(J20 / H25 engines)424.230.0
Transmission range switch lock bolt5.50.554.0
Oil pipe union bolts353.522.5
Drive plate bolts787.856.5
Interlock cable clamp screw2.20.221.5
Interlock cable outer mounting nut131.39.5

YH4
GRAND
VITARA
1. Clutch pedal
2. Clevis lock nut
3. Push rod
1. Clutch master cylinder
2. Clutch pipe
3. Clutch hose
4. Clutch operating cylinder
1. Pipe
2. Hose
3. Spanner
4. Flare nut wrench2, (a)
7C1-4 CLUTCH
ON-VEHICLE SERVICE
CLUTCH PEDAL HEIGHT
Adjust clutch pedal height by loosening clevis lock nut and turning
push rod as shown.
Clutch pedal height is normal if clutch pedal is about
20 mm (0.79 in.) higher than brake pedal.
After adjusting, tighten lock nut to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
CLUTCH PEDAL FREE TRAVEL
Depress clutch pedal, stop the moment clutch resistance is felt and
measure distance (clutch pedal free travel). Free travel should be
within following specification.
Pedal free travel ªaº: 15 ± 25 mm (0.6 ± 1.1 in.)
CLUTCH FLUID PIPE AND HOSE
REMOVAL
NOTE:
Do not allow fluid to get on painted surface.
1) Remove dust and dirt from each joint of hose and pipe to be dis-
connected and clean around reservoir cap.
2) Take out fluid with syringe or such.
3) Disconnect fluid pipe from hose.
NOTE:
To disconnect pipe from hose, separate them by using flare
nut wrench and spanner so as not to kink them.

YH4
GRAND
VITARA
3
4
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Circlip
2. Push rod
3. Piston
4. Cylinder
1. Circlip
2. Push rod
3. Piston stopper
CLUTCH 7C1-7
DISASSEMBLY AND ASSEMBLY CLUTCH
MASTER CYLINDER
DISASSEMBLY
1) Remove boot and then circlip with piston pushed in.
2) Remove push rod and blow compressed air gradually into hole
for pipe connection to remove piston assembly, using care to
prevent it from jumping out.
INSPECTION
Inspect all disassembled parts for wear or damage and replace
parts if necessary.
NOTE:

Wash disassembled parts with brake fluid.

Do not reuse piston assembly and circlip.
Inspect cylinder bore for scoring or corrosion. It is best to replace
corroded cylinder. Corrosion can be identified as pits or excessive
roughness.
NOTE:
Polishing bore of cylinder with anything abrasive is prohib-
ited, as damage to cylinder bore may occur.
Rinse cylinder in clean brake fluid. Shake excess rinsing fluid from
cylinder. Do not use a cloth to dry cylinder, as lint from cloth cannot
be kept away from cylinder bore surfaces.
ASSEMBLY
NOTE:
Before installation, wash each part in specified brake fluid.
1) Apply brake fluid to inside of piston assembly and cylinder body.
2) Install piston assembly into cylinder.
3) With piston pushed down, install circlip as shown.
And install boot.

YH4
GRAND
VITARA
ªAº
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Clutch operating cylinder
2. Hose
3. E-ring
7C1-8 CLUTCH
4) Tighten lock nut to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
5) For installation of master cylinder to vehicle, refer to INSTALLA-
TION described previously.
CLUTCH OPERATING CYLINDER
REMOVAL
NOTE:
Do not allow fluid to get on painted surfaces.
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Disconnect fluid hose from operating cylinder.
3) Remove operating cylinder attaching bolts and operating cylin-
der.
INSTALLATION
1) For air bleeding of master cylinder alone, it must be removed
from vehicle.
For procedures of removal and installation of master cylinder as-
sembly and air bleeding, refer to CLUTCH MASTER CYLINDER
section.
2) Apply small amount of grease to rod tip.
ªAº: Grease 99000-25010
NOTE:
Don't allow any grease to be on boot.
3) Install clutch operating cylinder and torque attaching bolts to
specification.
4) Connect clutch fluid hose and torque union bolt to specification.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 16.5 lb-ft)

YH4
GRAND
VITARA
7C1-14 CLUTCH
09917-58010 (G16 engine)
09923-73210
(J20 and H25 engines)
Bearing remover09923-36330 (G16 engine)
09923-36320
(J20 and H25 engines)
Clutch center guide09924-17810
Flywheel holder09925-98210
Input shaft bearing installer
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Flare nut161.611.5
Master cylinder nut131.39.5
Lock nut101.07.5
Flywheel boltsG16 engine787.856.5Flywheel boltsJ20 and H25 engines707.050.5
Clutch cover bolts232.316.5
Operating cylinder bolt505.036.5
Clutch hose union bolt232.316.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium grease
SUZUKI SUPER GREASE A
(99000-25010)
Clutch master cylinder clevis pin.

Release fork.

Push rod tip of operating cylinder.
SUZUKI SUPER GREASE I
(99000-25210)Input shaft spline front end.
Clutch fluid
(Brake fluid)DOT3 or SAE J1703

Clutch reservoir.

Clutch master cylinder.

Clutch operating cylinder.
SealantSUZUKI BOND No.1215
(99000-31110)Flywheel bolts
SPECIAL TOOLS

YH4
GRAND
VITARA
1. Match mark
1. Transfer rear case
2. Oil seal
ªAº
ªBº
TRANSFER 7D-3
ON-VEHICLE SERVICE
GEAR OIL
Refer to ªON-VEHICLE SERVICEº of Section 7A or 7A1.
TRANSFER OIL SEALS
REAR CASE OIL SEAL
1) Lift up vehicle horizontally.
2) Give match marks on joint flange and propeller shaft as shown
in figure.
3) Remove 4 bolts from rear propeller shaft flange and remove pro-
peller shaft.
4) Using screwdriver, remove oil seal.
5) Using special tool(A) and plastic hammer, pressfit new oil seal
up to case surface. Be sure to apply grease to oil seal lip.
ªAº: Grease 99000-25010
Special Tool
(A): 09940-53111
6) Clean and inspect sliding portion of propeller shaft front end
(where oil seal contacts) before installation and if even small
dent or scratch exists, correct and clean it again.
Then apply grease inside splines of propeller shaft.
ªBº: Grease 99000-25010
7) Install propeller shaft and torque universal joint flange bolts to
specification.
CAUTION:
Be sure to use only specified bolts, nuts and lock wash-
ers for universal joint flange.
Tightening Torque:
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
CENTER CASE OIL SEAL (Front side)
In addition to the procedure for rear case oil seal, it is necessary to
drain and refill gear oil of transfer. Refer to Section 7A ªON-VE-
HICLE SERVICEº for oil specification.

YH4
GRAND
VITARA
1. Wood block
2. Dash panel
t: 45 mm / 1.8 in.
H: 200 mm / 8 in.
W: 100 ± 150 mm / 4 ± 6 in.
1. Transmission jack
2. Engine rear mounting member
3. Gear shift lever case
4. Bolt
TRANSFER 7D-5
TRANSFER ASSEMBLY
Dismounting and remounting of transfer and transmission together
as a unit is described in Section 7A for Manual Transmission or 7B1
for Automatic Transmission, but it is also possible to dismount and
remount transfer assembly by itself as described below.
DISMOUNTING
IN ENGINE ROOM
1) Disconnect negative (±) cable from battery.
2) Remove distributor assembly (if equipped).
3) Place wood block between engine and dash panel so that it
serves as stopper when engine, transmission and transfer unit
hangs down as rear mounting member is removed.
CAUTION:
Make sure to use wood block to prevent contact which
may occur between dash panel and CMP sensor case
(G16), CMP sensor (J20) or intake manifold (H25), and fan
and shroud.
IN CABIN
1) Remove console box.
2) Remove shift lever of transmission and transfer.
ON LIFT
1) Drain transfer oil.
2) Remove rear propeller shaft.
3) Remove front propeller shaft.
4) Disconnect exhaust center pipe.
5) Disconnect speed sensor coupler.
6) Place transmission jack and remove mounting member.
7) Lower transmission jack gradually and check to ensure that
wood block serves as stopper between engine and dash panel.
8) Remove bolts for gear shift lever case.
9) Pull off breather hose.

YH4
GRAND
VITARA
1. 4WD switch
2. Transfer
3. Blank
4. Blank
5. ECM or PCM
6. Glove box7. Air pump assembly
8. Actuator
9. Axle lock clutch
10. Free axle hub
11. 4WD indicator lamp
7E-2 DIFFERENTIAL (FRONT)
4WD CONTROL SYSTEM
When the 4WD switch is turned ON by shifting the transfer shift lever, ECM (PCM) (G16 and J20 engine models)
or 4WD controller (H25 engine model) actuates (energizes) the air pump assembly. Then positive pressure is sent
from the air pump assembly to the actuator installed to the differential case and causes the axle lock clutch and
the free axle hub in the differential case to be engaged, resulting in the 4WD mode. Only when running in the 4WD
mode, front axles are joined to differential case, and they become free when 2WD mode is used (or when transfer
shift lever is shifted to N position), thereby reducing the power loss.